Patlite LR4 Complete Operation Manual

Signal tower

Hide thumbs Also See for LR4:

Complete operation manual (93 pages)

page of 64

/ 64
Bookmarks

Quick Links

Download this manual

PATLITEO

Thank you very much for purchasing our PATLITE product.

Notice

to Customer

•Request

the installation

and wiring be performed

professional contractor if construction work is involved

•Prior

to installation,

read this manual thoroughly

using this product to ensure correct use.

•After

reviewing

this manual, if there are any questions

regarding this product, please contact the nearest

PATLITE

office

listed

on the back

Notice

to Contractor

•Read

this manual carefully

•Be

sure

to return

this manual

by a

before

cover

of this manual

prior to installation.

to the customer

Signal Tower

LR4

TYPE

LR6

CompleteOperationManual

Safety Precautions

Model

Configuration

Part

Names

Outer Appearance

How

Wiring

Buzzer Pattern Set-up 20

How

the Folding

Unit

Method

Troubleshooting

Specifications

Replacement

Optional

895100502

1 LR5

1 LR7

Number

and

Install

use

Bracket

Detachment

Parts

Page

Need help?

Do you have a question about the LR4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Patlite LR4

Page 1 Install Wiring Buzzer Pattern Set-up 20 the Folding Bracket Unit Detachment Method Thank you very much for purchasing our PATLITE product. Notice to Customer Troubleshooting •Request the installation and wiring be performed by a professional contractor if construction work is involved •Prior...
Page 2 Safety Precautions NOTES TO BE OBSERVED SAFE OPERATION In order to prevent any damage to the user and other personnel or to assets, note the following: The indications for warning are divided into the following classes according to the degree of danger or damage incurred when the warning is not taken into consideration and the product is not correctly used ndicates a potentially dangerous condition:...
Page 3 Assembly Model L R 4 440 6 460 5 450 7 470 Tiers With Flashing/Buzzer No Flashing/Buzzer 12VDC CR51 - IWI W Off-white LR4•6 - WJ•PJ 100-240v AC - 01 •02 K Black*9 Direct Mount / Cable Pole Mount with...
Page 4 Part Names and Outer Appearance Outer Appearance List The full product appearance is indicated according to its model number. Refer to the model numbers as a reference to its appearance (Body Color: Off-White) Assembly Model Model 1 Tier 5 Tiers(Drawing is 5 Tiers.) LED Tiers Rated Voltage...
Page 5 Model Tier- 5 Tiers(Drawing is 5 Tiers Tiers.) Rated Voltage Mounting/Wiring Flashing/Buzzer Model 1 Tier- 5 Tiers(Drawing is 5 Tiers Tiers Rated Voltage Mounting/Wiring Flashing/Buzzer...
Page 6 Unit Model (Body unit) Model Rated Voltage Mounting/Wiring Flashing/Buzzer Model Rated Vo tage Mounting/Wiring Flashing/Buzzer Model Rated Voltage Mounting/Wiring Flashing/Buzzer...
Page 7 (Unit: mm) - DODWJBO - CIDCIW LR4 : Ø40 , LR5 : Ø50 LR6 : Ø60 , LR7 : Ø70 LR4 : Ø40 , LR5 • Ø50 LR6 : Ø60 , LR7 • Ø70 53 5 : 173.5...
Page 8 • L-bracket and Pole Mount with Cable Type ( (Unit: mm) - DOCUBC] - CJC]CUNO LR4 : Ø40 , LR5 : Ø50 , LR6 : Ø60 LR4 : Ø40 , LR5 : Ø50 , LR6 : Ø60 53 5 Material...
Page 9 • Circular Bracket and Pole Mount with CableType - C]ODPJNC) LR4. • Ø40 , LR5: Ø50 , LR6 • Ø60 LR4 • Ø40 , LR5 : Ø50 , LR6 : Ø60 53.5 Name Material Buzzer unit Head Cover : 173.5...
Page 10 (Unit: mm) Circular Bracket and Pole Mount with CableType • C]M2PJBW • ÜM2PJNW LR4 : Ø40 LR6 : Ø60 : Ø40 LR6 : Ø60 53 5 Name Material Buzzer unit Head Cover LED unit GIObe: LRO-1M2 : 243.5 Body LRCI LRÜ-2M2...
Page 11 (Unit: mm) • Folding Bracket and Pole Mount with Cable Type - D02QJBW - D02QJNW : Ø40 R6 : Ø60 LR4 • Ø40 : Ø60 53.5 Name Buzzer unit Head Cover - 102 : 173.5 Globe: unit - 202 : 213.5...
Page 12 • Direct Mount with Terminal Block Type (Body Unit) (Unit: mm) LR5 : Ø50 Name Material : Ø70 Head Cover Body Direct Mount Bracket Waterproof Packing Silicone Rubber Accessory HexagonNut with Flange (M3) HexagonNut with Flange (M4) Maximum Board Thickness: 3 pcs 3 pcs —...
Page 13 • If the pole type requires an IP65 rating, apply sealant to the screws, nuts and wire distribution hole when instal ing the compatible bracket onto the installation • • Although the LR4- mounting bolt moves prior to assembly, it is not a quality issue Be sure to mount the product in manner indicated below.
Page 14 Mounting Hole Screw/ Mounting Dimensional Drawing (3 places) (Unit: mm) 5-WJ LR5-WT 1200 LR6• 7-WJ LR7-WT 1200 5-WJ LR5-WT LR4•5• 6-PJ LR6• 7-WJ LR7-WT Recommended Torque Nameplate Wire Distribution 0.6 N.m Position Hole (0 12 ) • Mounting Wire Distribution...
Page 15 Wiring Warning • Be sure the power is disconnected before wiring and changing fuses. Possible cause of short-circuiting may occur. • Ensure the proper working voltage is used and that direct current or alternating current is properly applied Possible cause of damage may occur. Caution •...
Page 16 Wiring Example The following is a basic wiring example. If there are any special applications • Wire Type & Wire Gauge that require asking questions concerning this product, feel free to contact Power Supply Wire( Z, • •UL2464 / AWG18 your PAT LITE Sales Representative.
Page 17 Power SupplyWre Power Sup Wire Yellow Fuse 12 V DC LR5 only)(Class2)(No polarity) 24 V DC (Class2) (No polarity) External Contact Classification PLC(NPNTransistor) LR4— Flashing drown LEO Red LED Amber LED Green Green Lighting LED Blue Blue LED White White...
Page 18 Fuse Used when buzzer unit is attached Only apply voltage to Power SupplyWires. External Contact Classification PLC (NPN Transistor) Flashing/ Buzzer Output unit LR4 , LR6 Flashing Common Line Brown LED Red LED Amber LED Green Lighting LED Blue Buzzer...
Page 19 WX]TerminaI BlockArray liiiiiiiiiiiiiiü 123456789 Wj]Terminal BlockWiring Method Body Unit Remove the connector from the body unit before wiring Terminal Block Connector Recommended Lead-wire Specifications A minus driver etc. is used to pry the Wire Type Wire Gauge(SolidWire) Wre Gauge(FrayedWire lever slot of the Terminal Block open, UL1007 / UL1430 5mm2...
Page 20 • External Contact Capacity Is : Current Capacity Vs : Withstand Voltage IL : Leakage Current Ta : Ambient Tenperature 0112VDC 0224 V DC M2]100 - 240VAC Rated Load Volta e Si nal Wire Current 90 mA 40 mA 40 mA LED Unit (1 Tier) Contact Ca aci...
Page 21 How to use the Folding Bracket Folding bracket is a retractable type, which can be pushed down while a product is still attached when transporting equipment. (Fixed Position: 90 degrees to the right and 45 degrees to the right and left from an upright direction) When moving 90 degrees to the right When moving 45 degrees to the right from an upright position.
Page 22 Unit Detachment Method Refer to the fol owing diagrams when detaching the buzzer unit, recombining the LED Unit, etc. Also, scan the QR Code to see the "How To" video. Video Site Warning • Be sure the power is disconnected before working on this product Caution •...
Page 23 < LED Unit to Body > • Removal LED Unit While holding the body, turn the LED unit counterc ockwise, until it unlocks, then pull it upwards to remove. • Positioning Mark Body • Attachment Align the Positioning Mark after insertion, then turn the unit clockwise to lock Align the Positioning...
Page 24 < LED Unit to LED Unit > • Removal LED Unit While holding LED unit, turn the LED unit counterclockwise, Unit until it unlocks, then pull it upwards to remove to remove • Positioning Mark <Locked> <UnIocked> Body Attachment Align the Positioning Mark after insertion, then turn the unit c ockwise to lock Align the Positioning Mark...
Page 25 < Buzzer Unit to LED Unit > Removal Buzzer Unit Unit While holding LED unit, turn the buzzer unit counterclockwise, until it unlocks, then pull it upwards to remove it • Positioning Mark Unit Body • Attachment Align the Positioning Mark after insertion, then turn the unit clockwise to lock Align the Positioning Mark...
Page 26 < The case that Buzzer Unit can't be attached well > When Buzzer unit is detached, its state usually is such as below the figure. Buzzer Unit Groove Buzzer Unit UndersideView Body Removal Buzzer Unit When Buzzer unit is detached, the tab is located in the groove. Caution If Buzzer Unit can't be attached well, check whether the tab is located in the groove.
Page 27 If Buzzer U nitcan'tbeattached well,try this procedure. Turn the internal part of the Buzzer Unit counterclockwise until the tab fits in the groove. Attach the Buzzer Unit to the product. Turn this part counterclockwise. Turn this part counterclockwise. Groove Buzzer Unit UndersideView 27 —...
Page 28 < Head Cover Unit > Removal Head Cover While holding the LED unit, turn the head cover counterclockwise until it unlocks, then pull it upwards to remove Positioning Mark Unit <Locked> LED Unit Body • Attachment Align the Positioning Mark after insertion, then turn the unit clockwise to lock Align the Positioning Mark...
Page 29 <Unit Replacement Procedure> • Decreasing the LED Units Remove unit located above unit While holding the LED unit, turn the LED unit which is intended to be removed counterclockwise,until it unlocks, then pull it upwards to remove. Align the Positioning Mark after insertion, then turn the unit which is removed ([I) clockwise to lock...
Page 30 • Increasing the LED Units Remove unit located above Align the Positioning Mark after insertion, unit which is intended to be attached then turn the unit clockwise to lock it Align the Positioning Mark after insertion, then turn the unit which is removed ([l) clockwise to lock it.
Page 31 • Recombining the LED Units Remove unit located above While holding the LED unit, turn the LED unit which is intended to be relocated unit counterclockwise until it unlocks, then pull it upwards to remove Align the Positioning Mark after insertion, Remove the LED unit...
Page 32 Align the Positioning Mark after insertion, Align the Positioning Mark after insertion, then turn the unit which is removed (D then turn the unit which is removed clockwise to lock clockwise to lock...
Page 33 < The case that Unit can't be attached well> The structure of LED Unit is shown in the below figure Situation Structure Lens Unit Tab,Groove Positioning Mark Tab,Groove Body LED Unit Topside View Removal Unit When LED Unit is detached, the tab of lens is usually located in the groove Lens Groove...
Page 34 Caution f LED Unit can't be attached well, check wheter the tab of lens is located in the groove. f found in the tab is located out of the groove as below figure, refer to next page When LED Unit is detached, there is possibility that teh tab is located out of the groove as below figure f LED Unit such as shown in the figure is attached to the product again, the unit may damaged Lens Groove...
Page 35 If LED Unit can't be attached well, try this procedure Turn internal lens of the Unit counterlockwise until the tab fits in the groove. Attach the LED Unit to the product Lens Unit Underside View Lens Tab, Groove Tab, Groove LED Unit Topside View (Attachable)
Page 36 , LR7-02WTND <Body Unit> (LR5-02WTN • Removal While holding the direct mount bracket, turn the body counterclockwise until it unlocks, then pull it upwards to remove • Positioning Mark Body <Locked> Direct Mount Bracket • Attachment Align the Positioning Mark after insertion, then turn the unit clockwise to lock it •...
Page 37 Troubleshooting Prior to contacting your nearest PATLITE Sales Representative, refer to the following tips, and try to solve them in the following table. Problem Where to Check What to do Refer " Wiring" (pg_15-19) Is the electric wiring connected correctly? for proper wiring The LED does not light up.
Page 38 10 Specifications General Specifications ( @ ) Model Rated Voltage 24V DC Rated Voltage Operating Voltage Range Unit : 40mA Signal Wire Current Buzzer Unit : 40mA (Per Unit) Unit : 45mA Buzzer Unit : 300mA Power Supply Wire 0 7Al Less than 0.5ms Inrush Current...
Page 39 General Specifications LR5-Z01DÜDW Model 12V DC Rated Volta Rated Voltage ±10% Operating Voltage Range LED unit : gornA Signal Wire Current Buzzer Unit : 90mA (per Unit) LED unit Max. Buzzer Unit : 300mA Power Supply Wire 0.7A / Less than 15ms Inrush Current...
Page 40 General Specifications LRD-CJM2DDDW Model Rated Volta 100-240V 50/60Hz Operating Voltage Range 90-250V AC (50/60Hz) LED Unit Signal Wire Current Buzzer Unit : 40mA (Per unit) LED Unit : 45mA Buzzer unit : 300rnA (*1) at 25 C : 25AJ Less than 2ms Cold-start Power Supply Wire Inrush...
Page 41 Replacement Parts The following replacement parts for this product are available for the customer to change or replace Replacement Parts for LR4 O-ring 40 Head Cover 40 [W/U] Pole Bracket 40 [W/U] Filter Sheet Replacement Parts for LR5 O-ring 50...
Page 42 Replacement Parts for LR7 O-ring 70 Head Cover 70 [W/U/K] Filter Sheet Replacement Parts for WT Replacement PartsforLR4/LR51LR6 Terminal Block Pole Waterproof Ring 00000...
Page 43 Conformity Standards EMC Directive (EN 61000-6-4, EN 61000-6-2) ROHSDirective (EN 50581) Due to the characteristics Ofthe LED elements, a variation in difference Remarks of the color tone and brightness of every product may occur. LR4:Ø40 , LR5:Ø50 LR&.Ø60 , LR7IØ70...
Page 44 6 "Buzzer Pattern Set-up" Typ 90dB Environmental Buzzer sound No 4 was measured from the tota LR4:Ø40 , LR5:Ø50 Condition circumference of the buzzer Unit at 1m LR6:Ø60 , LR7:Ø70 UL508, CSA-C22.2 EMC Directive (EN 61000-6-4, EN 61000-6-2) Conformity Standards...
Page 45 Compatible Models Circular Bracket LR4- QJ ,LR5- PJ ,LR6. SZP-OOIW Compatible Pole POLE22-0100AN,POLE22-0300AN Specifications SZP-OOIW Model Mounting Location Indoor Only Protection Rating IP65 (with product attached) Accessories: Material Waterproof Packing Mass (Tolerance ± 100/0) 0.04kg No Accessories Pole Waterproof Ring...
Page 46 Pole Installation 1 Install the Pole Waterproof Ring in the Circular Bracket. Check that the 2 ribs are on the outside Insert Pole into the Circular Bracket. See the figure on the left for details on the direction of insertion Tighten the Binding Head Tapping Screws (2 pcs.) from underneath Circular...
Page 47 Compatible Models Circular Bracket LR4- QJ ,LR5- PJ ,LR6. SZP-002U Compatible Pole POLE22-0100AN POLE22-0300AN,POLE22-0800AN Specifications SZP-0021J Model Mounting Location Indoor Protection Ratin IP20 with roduct attached Material ADC12 Accessories: Mass (Tolerance ±10%) 0.11kg Pole Waterproof Ring No Accessories Binding Head Tapping S crew (2 pcs.)
Page 48 Pole Installation 1. Install the Pole Waterproof Ring in the Circular Bracket. Check that 2 ribs on the outside. pole 2. Insert Pole into the Circular Bracket. See the figure on the left for details on the direction of insertion. 3.
Page 49 Compatible Models Circular Bracket LR4-19Jl QJ ,LR5- PJ ,LR6- PJ SZP-003W Compatible Pole POLE22-0100AN,POLE22-0300AN Specifications SZP-003W Model Mounting Location Indoor Only IP65 (with product attached) Protection Rating Accessories: Material Waterproof Packing Mass (Tolerance ±IO%) 0 03kg Pole Waterproof Ring No Accessories...
Page 50 Pole Installation 1 Install the Pole Waterproof Ring in the Circular Bracket Check that 2 ribs on the outside. 2. Insert Pole into the Circular Bracket. See the figure on the left for pole details on the direction of insertion. 3.
Page 51 Compatible Models L-bracket LR4- LJ ,LR5- LJ ,LR6. SZL-OOI Compatible Pole POLE22-0300AT POLE22-0500AT,POLE22-1000AT Specifications Model SZL-OOI Mounting Location Indoor Only Material s pHC_p Mass (Tolerance ±10%) 0.09kg There are no contents of controlled Remarks substances exceeding the threshold for the RoHS...
Page 52 Compatible Models Folding Bracket LR4- SZQ-OOIW Compatible Pole POLE22-0100AN,POLE22-0300AN Specifications Model SZQ-OOIW Mounting Location ndoor Only P65 (with product attached) Protection Rating Material Accessories: Mass (Tolerance ±10%) O.09kg Pole Waterproof Ring NO Accessories Binding Head Tapping S crew (2 pcs.)
Page 53 Pole Installation 1. Install the Pole Waterproof Ring in the Folding Bracket. Check that the 2 ribs are on the outside. 2. Insert Pole into the Folding Bracket. See the figure on the left for details on the direction of insertion 3.
Page 54 LR4- QJ ,LR5 Wallmount Bracket LR6- SZK-OOI Compatible Pole POLE22-0100AN POLE22-0300AN POLE22-0800AN Specifications SZK-OOIU Model Mounting Location Indoor Only Protection Rating IP20 with roduct attached Material ADC12 Mass (Tolerance ±10%) Accessories: 0 19kg No Accessories Hexagon SocketSetScrew (2 pcs )
Page 55 Pole Installation 1. Insert Pole into the Wallmount Bracket. See the figure on the left details on the direction of insertion. 2. Secure with the Hexagon Socket Set Screws (2 pcs.) on the Pole Bracket. Installation using materials other than the specified ! Notice accessories is not covered under warranty...
Page 56 LR4. WJ ,LR5- WJ WT Wallmount Bracket SZK-002 [W/U] Specifications Model SZK-002 Mounting Location Indoor Only P65 (with product attached) Protection Rating Material Mass (Tolerance ±10%) O.06kg There no contents of controlled Remarks substances exceeding the threshold for the RoHS Directive.
Page 57 LR6- WJ ,LR7- WJ WT Wallmount Bracket SZK-003 [W/U] Specifications SZK-003 [W/U] Model Mounting Location Indoor Only IP65 (with product attached) Protection Ratin Material Mass (Tolerance ±10%) 0 07k There are no contents of controlled Remarks substances exceeding the threshold for the RoHS Directive.
Page 58 Product Attachment 1. Insert the mounting screws of the product into the Wallmount Bracket. See the figure on the left for details on the direction of insertion. 2. Secure the product with the flanged nuts (3 pcs.) from underneath Bracket. Recommended Torque 0.6 Nm...
Page 59 Dimensional Drawing Product Mounting (LR6) • Dimensional Drawing Hole (3 places) (Unit mm) Mounting Hole ( 06 places) Wire Distribution Hole (012) Wire Distribution Hole (Ö22) Product Mounting (LR4, LR5) Screw/Nut Hole laces Recommended Torque Ø57 1.4 N m Ø90...
Page 60 Product Attachment 1 Insert the mounting screws of the product into the Circular Bracket See the figure on the left for details on the direction of insertion. 2 Secure the product with the flanged nuts (3 pcs ) from underneath Bracket.
Page 61 Compatible Models Pole LR4- POLE22-[0100/0300/0800] A N LR5- ,LR6. Compatible Optional Parts SZP-OOIW SZP-002U SZP-003W SZQ-OOIW SZK-OOIU POLE22-0100AN POLE22-0300AN POLE22-0800AN Specifications POLE22-0100AN POLE22-0300AN Model POLE22-0800AN Mountin Location ndoor Only Accessory :Binding Head T apping Screw (2pcs.) Pole length L (mm)
Page 62 LR4. Pole POLE22-[0300/0500/1000] A T ,LR6. Compatible Optional Parts SZL-OOI Specifications POLE22-0300AT Model POLE22-0500AT POLE22-1000AT Mountin Location Indoor Only Pole th L mm 1000 Accessory :Hexagon Nut (2pcs.) Material Mass (Tolerance ±10%) Plain Washer (2pcs.) 0 15kg 0 26kg 0 52kg No Accessories BindingHeadTappingScrew(2pcs .)
Page 63 Pole Bracket Installation Binding Head Tapping Screw 3x12 2pcs 1. Install the Pole Waterproof Ring in the Pole Bracket. Check that 2 ribs on the outside Recommended Torque 2. Insert Pole into the Pole Bracket. See the figure on the left for Pole Bracket details...
Page 64 PATLITE (THAILAND) CO., LTD. 'h ttp://www.pat/ite.co.th/ (Note) • Dimensions and specifications may change without notice due to continual product improvement. • PATLITEand the PATLITE logo is a trademark, or registered trademark of the PATLITECorporation of Japanand each country. B95100502 '16.12...

This manual is also suitable for:

Lr5 Lr6 Lr7