2gig Technologies EDGE Installer Quick Start Manual

2GIG ® Security & Smart Home System
®
2GIG Security & Smart Home System
2GIG EDGE Installer Quick Start Gu
E Panel
2GIG EDGE Installer Quick Start Guide
10029907 Rev-C | 2GIG-EDG-NA | EDGE Panel
er the lower lip on the back of the chassis, and flip the EDGE
10029907 Rev-C | 2GIG-EDG-NA | EDGE Panel
ush until it clicks into place.
I
I ntroductIon
ntroductIon
This quick start guide introduces 2GIG alarm dealers and professional installers to
This quick start guide introduces 2GIG alarm dealers and professional installers to
2GIG EDGE panel hardware installation and the Installer Toolbox. It describes the
2GIG EDGE panel hardware installation and the Installer Toolbox. It describes the
process of programming zones, keyfobs, and keypads for the EDGE Panel and how to
process of programming zones, keyfobs, and keypads for the EDGE Panel and how to
add and remove Z-Wave
add and remove Z-Wave
Installer Toolbox menu.
Installer Toolbox menu.
EdGE P
EdGE P
Choose the Location for the 2GIG EDGE Panel's Backplate
Choose the Location for the 2GIG EDGE Panel's Backplate
Before mounting the backplate, choose a location. Work with the end user to
determine the best location. Always choose an indoor location protected from
Before mounting the backplate, choose a location. Work with the end user to
temperature extremes.
determine the best location. Always choose an indoor location protected from
Recommended Tools and Equipment
temperature extremes.
To install the system, these tools and equipment are recommended:
Recommended Tools and Equipment
➣ 2-Conductor Power Wire (if connecting power supply to the panel's terminal
block)
To install the system, these tools and equipment are recommended:
➣ Drywall Saw (or equivalent)
➣ 2-Conductor Power Wire (if connecting power supply to the panel's terminal
➣ Ladder
➣ Screwdrivers block)
➣ Staple Gun
➣ Drywall Saw (or equivalent)
➣ Wire Stripper
➣ Ladder
Choose the Wall Location
➣ Screwdrivers
To choose a wall location:
➣ Staple Gun
➣ Always choose a location that is above ground and centrally located. Do
➣ Wire Stripper
NOT install the Panel below ground level, because wireless range may be
Choose the Wall Location
impaired.
➣ Do NOT connect the Panel to a light switch-controlled outlet.
To choose a wall location:
➣ Avoid choosing a location that can be easily viewed from doors or windows.
➣ Always choose a location that is above ground and centrally located. Do
➣ Avoid choosing a location that is within reach of small children.
NOT install the Panel below ground level, because wireless range may be
➣ Avoid choosing a location in direct sunlight.
impaired.
NOTE: If necessary, the Panel can be mounted on a stand that can be placed on
➣ Do NOT connect the Panel to a light switch-controlled outlet.
a flat surface, such as desk or counter using the 2GIG Desktop Kit. However, this
option may affect compliance with state or regional codes. For 2GIG Desktop Kit
➣ Avoid choosing a location that can be easily viewed from doors or windows.
installation instructions, refer to the 2GIG EDGE Installation Manual.
➣ Avoid choosing a location that is within reach of small children.
External Attic Mount Antenna Installation (Optional)
➣ Avoid choosing a location in direct sunlight.
ng Wall Bracket & Connect the AC Power Supply
If you will be installing the optional External Attic Mount Antenna, refer to the 2GIG
NOTE: If necessary, the Panel can be mounted on a stand that can be placed on
EDGE Installation Guide.
a flat surface, such as desk or counter using the 2GIG Desktop Kit. However, this
NSI/NFPA 70: National Electric Code in the United States, you
1. Align Backplate to Mark Hole Locations
option may affect compliance with state or regional codes. For 2GIG Desktop Kit
supply retaining bracket (not required in Canada).
Create mounting holes, and cut
installation instructions, refer to the 2GIG EDGE Installation Manual.
a slot in the dry wall for the AC
External Attic Mount Antenna Installation (Optional)
power cord and other electrical
Fastener
wiring (if needed).
If you will be installing the optional External Attic Mount Antenna, refer to the 2GIG
EDGE Installation Guide.
1. Align Backplate to Mark Hole Locations
Create mounting holes, and cut
a slot in the dry wall for the AC
power cord and other electrical
wiring (if needed).
Indicates Mounting Hole
Nortek Security & Control LLC
Indicates Mounting Hole
Nortek Security & Control LLC
® devices from the network. To get started, navigate to the
®
devices from the network. To get started, navigate to the
I
anEl nstallatIon
I
anEl nstallatIon
Decora Style – Center Fastener
Secure with Fastener
Back Plate
Attached to Wall
LEVEL
LEVEL
NOT LEVEL
NOT LEVEL
2. Mount th
Use the four (4
NOTE: The Wa
Illustra
Install th
Wall Tampe
POWER IN
Barrel Con
POWER IN
3. Hang the
Attach the pan
for easy acces