Related Manuals for AUSTRALIAN MONITOR IS SERIES
Summary of Contents for AUSTRALIAN MONITOR IS SERIES
- Page 1 IS SERIES 600W/1200W/1600W STEREO PRO AUDIO AMPLIFIERS INSTALLATION AND OPERATION MANUAL...
-
Page 2: Important Safety Information
7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the Australian Monitor Inc is not responsible for damage to means of grounding of a piece of equipment is not defeated. -
Page 3: Table Of Contents
4 ohms and the IS1600 delivers 800 watts per channel @ 4 ohms. REAR PANEL Designed for permanent installations where high quality audioreproduction is required on a small budget, the IS series INSTALLATION deliver the sound quality & features contractors require. -
Page 4: Front Panel
Peak Programme Meter (P.P.M.) NOTE: The amplifier is not damaged by running into clipping, but speakers may be. To maximise the life of your speakers, try to keep clipping infrequent. PAGE 4 IS SERIES INSTALLATION & OPERATION MANUAL... -
Page 5: Rear Panel
(i.e. Operating in stereo mode) or whether the input signal from channel A is being fed through to channel B. NOTE: This is not Bridge mode. IS SERIES INSTALLATION & OPERATION MANUAL IS SERIES INSTALLATION & OPERATION MANUAL PAGE 5... -
Page 6: Installation
COOLING lug that connects directly to the chassis of the Each channel of your IS Series amplifier is cooled by an axial fan which connector. Do not link this lug to pin 1 at the amplifier s draws cool air from the front of the amplifier and expels heated air out input as it will defeat the amplifier s input grounding the rear of the amplifier. - Page 7 Connecting through a single connector has the advantage of minimising connections, preserving phasing and simplifying channel allocation, which is particularly important when bi-amping. PAGE 7 IS SERIES INSTALLATION & OPERATION MANUAL...
-
Page 8: Operation
We recommend turning the attenuators on your amplifier down when turning the unit on. When you power up your IS Series, your amplifier goes through an initialising period before it will accept signal. The Inrush Current Suppression (ICS) circuit is in operation for the first 0.5... - Page 9 This may be due to any of the previously in an electrically noisy environment, problems may occur. The three mentioned gremlins. Your IS Series amplifier has a "Signal Ground Lift" "E"s of hum and hum related noise which can plague your audio switch which disconnects the input ground wiring from the amplifier.
-
Page 10: Maintenance
FANS service or maintenance of your amplifier. Your IS Due to the openness of the air path through your IS Series amplifier, Series amplifier will need minimal maintenance. very little dust should settle within the amplifier. The unit has been... -
Page 11: Specifications
DAMPING FACTOR (into 4 ohms) >200 >200 >200 DAMPING FACTOR (into 8 ohms) >100 >100 >100 INPUT IMPEDANCE 20Kohm 20Kohm 20Kohm SIGNAL/NOISE RATIO (20-20kHz) >90dB >90dB >90dB WEIGHT 16.5kg 20.5kg 22.0kg DIMENSIONS (WXDXH) 483x452x89mm 483x452x89mm 483x452x89mm PAGE 11 IS SERIES INSTALLATION & OPERATION MANUAL... - Page 12 AUSTRALIA AND NEW ZEALAND www.australianmonitor.com.au SYDNEY MELBOURNE BRISBANE ADELAIDE PERTH AUCKLAND (NSW & ACT SALES) (VIC & TAS SALES) (QLD SALES) (SA & NT SALES) (WA SALES) (NZ SALES) 149 Beaconsfield 22/277 42 Commercial Road 31 Walsh Street 299 Fitzgerald Street Unit B, 11 Piermark Street Silverwater Middleborough Road...
Need help?
Do you have a question about the IS SERIES and is the answer not in the manual?
Questions and answers