Autronica AutroGuard Multicriteria Protector V-120 Series Technical Handbook

Hide thumbs

Table Of Contents

100

Table of Contents

Table of Contents
Introduction
Scope
The Manual
Target Audience
Reference Documentation
Downloading Technical Documents
Technical Terms and Abbreviations
Document Revision Log
Safety
Important Safety Information
Intended Use
Safety Notice
Safety Regulations
National Standards and Regulations
Mounting, Installation, Commissioning and Maintenance
Modifications to the Products
Compliance with Standards and Directives
Recommendations for Latest Available Firmware and Operating System
Environment Compatibility
Recycling
Disposal
Protector Overview
Product Decription
Details for Ordering
Ordering Information Accessories
Ordering Information Autroguard Retro Variants
Labeling
Marking on Protector (Bottom)
Marking on Protector Base (Inside)
Marking on Protector Top, EX Only
QR Code and Data Matrix Code
QR and Data Matrix Code Information
QR Code Placement on Protector
Data Matrix Code Placement on Protector Base's Tagholder
Tag Holder for Labels
Dimensions and Outlines
Protector Base
Protector with Visual Alarm Device (VAD)
Protector Without Visual Alarm Device (VAD)
Protector for Retrofit Mounting Onto BWA-100/BWA-101 (Height)
Technical Specifications
Protector and Base
Integrated Sounder
Tones
Sound Pressure Levels for Tones
Integrated VAD - Current Consumption
Integrated VAD and Sounder - Current Consumption
Functional Description
General
Chamber Design
Dyfi 3D
DYFI 3D - Particle/Smoke Signature Analysis
DYFI 3D - Dynamic Filtering
Sensitivity Classes for Environmental Adaptivity
Operation Classes
Heat Response Categories
Selfverify® 2.0 Function
Cover Detection
Protector "Alive Signal
LED Behavior
Visual Alarm Device (VAD)
Compliance with EN54-23
Coverage Volume
Category C - Ceiling Mounted Devices
Category O
Visual Alarm Device (VAD) Intensity
Consideration Factors for VAD Sensitivity Settings
VAD Intensity Settings
VAD Intensity - White VAD and Red VAD
Flash Rate
Audible Alarm Devices
General
Sound Pressure Level
Sound and Pulse Patterns
Planning
Reference to National/Local Regulations
Enviromental Requirements
Location / Required Space
Area Coverage and Monitoring Distance
Smoke Detection
Heat Detection
Current Consumption on Detection Loop
Mounting Instructions
Cable Entries/Exits on the Protector Base
Cable Entry for Concealed Conduit Wiring
Cable Entries/Knockout Stampings for Surface-Mounted Wiring
Mounting the Protector Base
Considerations before Mounting
Template for Marking and Drilling Holes
Mounting for Concealed Conduit Wiring
Mounting Onto a Ceiling Box / Wall Box
Mounting Onto a Conduit Box
Mounting for Surface-Mounted Wiring
Connecting Loop Cables
Cable Requirements
Wire Routing Arrangement Inside Protector Base
Wire Insulation Stripping
Spring Cage Connection
Connections - Overview
Loop Connections
LED Connection
Branch-Offs
Alignment Marks on the Protector
Mounting the Protector Onto the Base
Locking/Unlocking the Protector to the Base
Removing the Protector from the Base
Retrofit Mounting Onto Existing Autrosafe Base
Bwa-100/Bwa-101
Labeling the Protector Base / Tag Holder
Protector Cover
Preparing for Configuration
Introduction
Tools Requirements
Alternative Ways of Identifying Serial Numbers
Alternative a - Using QR Code Reader (Recommended)
Alternative B - Using the Rip off Label Inside the Autroguard Base
Labeling Bases with Tag Name Labels
Alternative a - Using a QR Code Reader
Alternative B - Using the Rip off Label
Scanning each Loop with AS2000
Generating an Excel File
Merging Tag Names, Serial Numbers and LSI
Autrosafe Configuration Tool
Troubleshooting
Configuration Recommendations
Introduction
Hotel Rooms
Apartments
Freezers and Cold Stores
Clean Rooms and Computer Rooms
Configuration for Autrosafe
Introduction
Autrosafe Configuration Tool Requirements
Site Configuration System Settings
Detector Defaults - LED on Alarm/Led Alive Blink
Sound and Pulse Patterns
Adding System Units
Autroguard Default Settings
Set Autroguard Defaults Menu
Multi
Ex/S
Sounder
Visual Alarm Device (VAD)
Postfix
Autroguard Settings for Multiple Protectors
Autroguard Individual Settings
Fire Alarm Devices
Automatic Test Mode
Cover Detection Sensitivity
Heat Response Categories
Operation Classes
Sensitivity Settings for Environmental Adaptivity
Visual Alarm Device (VAD)
Sound Pressure Level - Sounders
Matching Protectors/Bases with Autrosafe Configurations
Configuration for Autroprime
Introduction
Autroprime Software Requirements
Global Settings
Sound Patterns
Visual Alarm Device (VAD)
Individual Settings
Operation Class Day Mode
Heat Response Category Day Mode
Sensitivity Class Day Mode
Operation Class Night Mode
Heat Response Category Night Mode
Sensitivity Class Night Mode
Enable Automatic Test Mode
Use LED Alive Blink
Use Blink on Alarm
External Output Follow Alarm
Cover Detection Sensitivity
Testing and Maintenance
Selfverify® 2.0 Function
Visual Inspection
Manual Testing
Introduction
Test Equipment
Automatic Test Mode
Cleaning Procedure
Replacing a Protector (Hot Swap)
Calibrating the Cover Detection Sensor
Method A: Re-Calibrating Using a Protector Cover
Method B: Re-Calibrating Using AS2000 Loop Diagnostic Tool
Accessories
Locking Tool for Locking the Protector to the Base
QR Code Reader
WAS-2000 and AS2000 Loop Diagnostic Tool
Cover
Air Duct Sampling Unit
Air Duct Sampling Unit - Stainless Steel
Conduit Box
Telescope Removal Tool
Ground Device
Test Gas
Testfire / solo 365 Test Tool
Appendix
UL Regulatory Information
Index

Quick Links

1 Introduction
Download this manual

utronica Fire And Security AS

Table of Contents

Need help?

Do you have a question about the AutroGuard Multicriteria Protector V-120 Series and is the answer not in the manual?

Autronica AutroGuard Multicriteria Protector V-120 Series Technical Handbook

Quick Links

Need help?

Questions and answers

Related Manuals for Autronica AutroGuard Multicriteria Protector V-120 Series

Table of Contents