Autronica AutroGuard Multicriteria Protector V-430 Series Technical Handbook
Autronica AutroGuard Multicriteria Protector V-430 Series Technical Handbook

Autronica AutroGuard Multicriteria Protector V-430 Series Technical Handbook

Table of Contents

Advertisement

Quick Links

utronica Fire And Security AS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AutroGuard Multicriteria Protector V-430 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Autronica AutroGuard Multicriteria Protector V-430 Series

  • Page 1 utronica Fire And Security AS...
  • Page 2 This publication, or parts thereof, may not be reproduced in any form, by any method, for any purpose. Autronica Fire and Security AS and its subsidiaries assume no responsibility for any errors that may appear in the publication, or for damages arising from the information in it.
  • Page 3: Table Of Contents

    3.6.2 Protector with Visual Alarm Device (VAD) ......19 3.6.3 Protector without Visual Alarm Device (VAD) ......20 3.6.4 Protector for Retrofit Mounting onto BWA-100/BWA-101 (Height) ................... 20 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS...
  • Page 4 9. Mounting Instructions ............. 47 Cable Entries/Exits on the Protector Base ........47 9.1.1 Cable Entry for Concealed Conduit Wiring ......47 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS...
  • Page 5 11.5 Clean Rooms and Computer Rooms ..........75 11.6 Table Overview – Applications/Settings ..........75 12. Configuration for AutroSafe ..........79 12.1 Introduction ..................79 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS...
  • Page 6 14.5 Replacing a Protector (Hot Swap) ............. 104 14.6 Calibrating the Cover Detection Sensor ..........105 14.6.1 Method A: Re-calibrating Using a Protector Cover ....105 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS...
  • Page 7 15.11 Testfire / Solo 365 Test Tool ............. 114 16. Appendix ..............115 16.1 UL Regulatory Information ..............115 17. Index ................116 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS...
  • Page 8: Introduction

    Doc-1004339 AutroGuard-sound-pressure-levels, English Doc-1004281 1.5 Downloading Technical Documents All relevant technical documents can be downloaded from the Autronica product web at www.product.autronicafire.com/products AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS...
  • Page 9: Technical Terms And Abbreviations

    Bajonet ring Rotatable bajonet ring on the protector head used to easily connect the protector to the base. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 3...
  • Page 10: Document Revision Log

    Revision Date Description/Corrections Revision 1 2020-06-29 Officially approved by Autronica Fire and Security AS Revision 2 2021-05-17 • Added part numbers for Air Duct Samling Units and Removal tool • Added new ch. 10 “Preparing for Configuration” • Some changes/added information in technical specifications ch. 4 (system compatibility) •...
  • Page 11: Safety

    DISCLAIMERS, LIMITATIONS OF LIABILITY PRODUCT WARNINGS THESE PRODUCTS ARE INTENDED FOR SALE TO, AND INSTALLATION BY, AN EXPERIENCED PROFESSIONAL. AUTRONICA FIRE AND SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL FIRE RELATED PRODUCTS.
  • Page 12: Intended Use

    ADEQUATE WARNING OR PROTECTION FROM, FIRE , SMOKE; OR (III) WILL WORK PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS. 2.2 Intended Use The protector is intended for use in Autronica fire detection systems and with the environmental conditions described in this handbook. 2.3 Safety Notice...
  • Page 13: Mounting, Installation, Commissioning And Maintenance

    Contact your local Autronica contact or dealer for further information. Autronica Fire and Security AS disclaims all liability or responsibility for any injuries or death, damage, faults, malfunctioning and safety risks that may occur due to the use of a product that has been modified.
  • Page 14: Environment Compatibility

    This product should not be mixed with other commercial wastes for disposal. Make sure to comply with all local and currently applicable laws and regulations. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 8...
  • Page 15: Protector Overview

    Autronica provides also several different variants of protectors specifically intended for retrofit purposes. These protectors can easily be mounted onto an existing AutroSafe base (BWA-100/BWA-101).
  • Page 16: Details For Ordering

    Protector Overview 3.2 Details for Ordering For information about part numbers for AutroGuard® variants, please visit the Autronica product portal at http://product.autronicafire.com. Use the type configuration matrixes in the following chapters when ordering a variant of the V-430 or V-530 series.
  • Page 17 V-120 Ex ia/Ex ic SIL2 base, without external LED output. Black. 116-V-120-CC V-120 Ex ia/Ex ic SIL2 base, without external LED output. Customized color to be specified. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 11...
  • Page 18: Ordering Information Accessories

    AutroGuard Retro variant - replaces BHH-320 116-BHH-520/SPARE AutroGuard Retro variant - replaces BHH-520 116-BHH-520/EX/SPARE AutroGuard Retro variant - replaces BHH-520/EX AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 12...
  • Page 19: Labeling

    Drawing Reference Marking on protector bottom DOC-1003908 Marking on protector top DOC-1003788 Marking on protector base DOC-1003909 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 13...
  • Page 20: Marking On Protector (Bottom)

    The illustration below shows all available markings. The actual marking on the protector depends on the variant. ETL listing or logo UL-268 marking alarm temperature Drawing no. DOC-1003908 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 14...
  • Page 21: Marking On Protector Base (Inside)

    The illustration below shows all available markings. The actual marking on the protector depends on the variant. ETL listing or logo Drawing no. DOC-1003909 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 15...
  • Page 22: Marking On Protector Top, Ex Only

    Protector Overview 3.3.3 Marking on Protector Top, EX only Marking – do not paint Drawing no. DOC-1003788 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 16...
  • Page 23: Qr Code And Data Matrix Code

    (the QR code shown in the illustration is an example used only for the purpose of indicating the placement of the QR code). ETL listing or logo AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 17...
  • Page 24: Data Matrix Code Placement On Protector Base's Tagholder

    (customer specified) is to be placed on the tag holder (covering the data matrix code). The maximum size of the label is 29 x 10 mm (as shown below). AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 18...
  • Page 25: Dimensions And Outlines

    Protector Overview 3.6 Dimensions and Outlines 3.6.1 Protector Base 3.6.2 Protector with Visual Alarm Device (VAD) AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 19...
  • Page 26: Protector Without Visual Alarm Device (Vad)

    Protector Overview 3.6.3 Protector without Visual Alarm Device (VAD) 3.6.4 Protector for Retrofit Mounting onto BWA-100/BWA-101 (Height) With VAD Without VAD AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 20...
  • Page 27: Technical Specifications

    • Loop Driver Module BSD-310/BSD-311 revision 7 or newer Operating temperature for EN54 variants -30 to +70 °C (+80°C when configured as heat detection only) AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 21...
  • Page 28: Integrated Sounder

    Smoke and Multi: UL 268, ULCS529 (/UL variants are not EN54 approved) Heat (only Heat Response Category A1 is certified): UL 521, ULC S530 For details on certifications, see Autronica’s product web. 4.2 Integrated Sounder Technical specifications INTEGRATED SOUNDER Sound pressure (dB @ 1m)
  • Page 29: Tones

    3650 Hz Continuous 3650 Whoop BS Fire 800 - 970 Hz 800-970 tone DIN tone DIN33404- 1200 - 500 Hz 1200-500 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 23...
  • Page 30: Sound Pressure Levels For Tones

    3600 - 1800 Hz 1 Hz DIN tone 3600-1800 Hz (DIN33404-3) 4.4 Sound Pressure Levels for Tones Measurement angles Vertical plane Horizontal plane AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 24...
  • Page 31 66.14 66.24 82.74 83.44 83.54 83.54 78.44 79.44 80.44 80.44 77.34 78.14 72.74 72.74 81.44 82.24 74.74 74.84 81.64 82.54 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 25...
  • Page 32 74.94 -0.2 82.44 82.44 68.94 68.94 78.94 79.04 71.24 71.04 -0.2 72.34 72.24 -0.1 73.94 73.94 73.14 73.14 74.44 74.44 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 26...
  • Page 33 71.64 71.64 73.74 74.74 81.54 81.74 69.94 70.84 77.44 77.54 73.14 73.74 69.54 69.84 72.84 73.54 72.94 73.04 74.64 75.64 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 27...
  • Page 34 71.24 71.24 74.34 74.44 81.64 81.84 70.74 70.74 77.74 77.74 73.64 73.74 69.84 70.04 73.14 73.34 72.74 72.74 75.14 75.34 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 28...
  • Page 35: Integrated Vad - Current Consumption

    12 m at 3 m height. For a (specified at 2,5m height) white VAD, high intensity is to be configured. *Available for V-430 only. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 29...
  • Page 36: Integrated Vad And Sounder - Current Consumption

    12 m at 3 m height. For a white VAD, high intensity is to be configured. *Available for V-430 only. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 30...
  • Page 37: Functional Description

    Smoke detection transmitter Two forward-scattering LEDs Smoke detection One IR, one orange. receiver Smoke detection transmitter One IR backward-scattering AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 31...
  • Page 38: Dyfi 3D

    Black smoke flaming fires Smouldering fires AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 32...
  • Page 39: Dyfi 3D - Dynamic Filtering

    The pollution filter maintains the chosen sensitivity throughout the protector’s entire lifetime, even with a polluted protector. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 33...
  • Page 40: Sensitivity Classes For Environmental Adaptivity

    Heat detection only Smoke only Optical detection only For information on the configuration of Operation Classes, refer to chapter 12.7.5. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 34...
  • Page 41: Heat Response Categories

    *** Applies to Operation Class Heat only. For information on the configuration of Heat Response Categories, refer to chapter 12.7.4. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 35...
  • Page 42: Selfverify® 2.0 Function

    Functional Description 5.7 SelfVerify® 2.0 Function As an add-on feature, Autronica provides the SelfVerify® 2.0 system function. The function is performed automatically every 24 hours, and is a calibrated self-test of the sensor elements verifying that the sensitivity of the protector is within the approved range. In addition to the daily system test, SelfVerify®...
  • Page 43: Protector "Alive Signal

    3 times every five seconds for a smoke/heat detector 4 times every five seconds for • smoke/heat/CO detector (Yellow LED is not yet supported). AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 37...
  • Page 44: Visual Alarm Device (Vad)

    With reference to EN54-23, the following categories apply to the coverage volume for the AutroGuard® protector’s VAD: C, ceiling mounted devices • O, open class devices • AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 38...
  • Page 45: Category C - Ceiling Mounted Devices

    To convert the coverage diameter y to the width of a square room: Width of square room = / 1.414 m AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 39...
  • Page 46: Category O

    Visual Alarm Device (VAD) 6.4 Category O Category O (Open Category) is Autronica’s specified coverage volume for 2,5m mounting heights. Category O has lower power consumption than category C (refer to table in Technical Specifications, chapter 0). The maximum number of VADs depends on the total load on the loop.
  • Page 47: Vad Intensity - White Vad And Red Vad

    Red Visual Alarm Device Flash Rate 0.5 Hz 1 Hz High C-3-8 Low C-3-5 O-2.5-4 Refer to Configuration, chapter 12.7.7. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 41...
  • Page 48: Audible Alarm Devices

    (for example, maritime general emergency signal, 7 short, 1 long). Refer to Configuration, chapter 12.3.2. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 42...
  • Page 49: Planning

    Security products must follow the instructions in this handbook and other applicable handbooks or standards in order to ensure safe operation of the products and services. Autronica Fire and Security is not responsible for ensuring that the products are installed according to national/local regulations. 8.2 Enviromental Requirements 8.2.1 Location / Required Space...
  • Page 50: Area Coverage And Monitoring Distance

    Ceiling height Area of coverage Under 6 80 m 7,5 meters +6 – 12 100 m 9 meters Over 12 See NS-3960:2013 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 44...
  • Page 51: Heat Detection

    Note that if Operation Class Heat only is used, the guidance for heat detection applies. Ceiling height Area of Monitoring Under 6 20 m 3,5 meters Over 6 Not permitted AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 45...
  • Page 52: Current Consumption On Detection Loop

    Base + protector head Alarm (Red LED indicator ON) 1,8mA Base + protector head Fault (Yellow LED indicator ON) 2,3mA AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 46...
  • Page 53: Mounting Instructions

    (See Template for Marking and Drilling Holes, chapter 9.2.2). Location of Visual Alarm Device AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 47...
  • Page 54: Cable Entries/Knockout Stampings For Surface-Mounted Wiring

    (knockouts) on the side of the protector base (see drawing) which allow easy entry of the cables to the interior (two 9x12mm and two 9x20mm entries). 9 mm 9 mm AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 48...
  • Page 55: Mounting The Protector Base

    (See Template for Marking and Drilling Holes, chapter 9.2.2). Location of Visual Alarm Device AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 49...
  • Page 56: Template For Marking And Drilling Holes

    For installation purposes, only use the 1:1 template printed on the protector base’s packaging box. Location of cable entry in base Alternative mounting AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 50...
  • Page 57: Mounting For Concealed Conduit Wiring

    • Feed the cables through the Ø25 mm cable entry as shown • Mount the protector base to the ceiling by fastening the screws AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 51...
  • Page 58: Mounting Onto A Ceiling Box / Wall Box

    • Feed the cables through the Ø25 mm cable entry as shown • Mount the protector base onto the box by fastening the screws AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 52...
  • Page 59: Mounting Onto A Conduit Box

    • Feed the cables through the chosen cable entries • Mount the protector base onto the conduit box by fastening the screws AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 53...
  • Page 60 Mounting Instructions AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 54...
  • Page 61: Mounting For Surface-Mounted Wiring

    • Mount the protector base to the ceiling by fastening the screws • Feed the cables through the cable entries as shown (the illustrations show two different cable layout alternatives) AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 55...
  • Page 62: Connecting Loop Cables

    (red/black) is used as a reference only. The colors may be different and will vary depending on the installation, applicable standards or local regulations. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 56...
  • Page 63: Wire Routing Arrangement Inside Protector Base

    The wires must be supported by the cable holders. Make sure that the wire routing arrangement shown below is used (the arrows point to the cable holders). Cable holder Cable holder AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 57...
  • Page 64: Wire Insulation Stripping

    Measure the length from the edge of the connector to the strip mark indicated on the drawing • Use a wire stripping tool to strip the cable AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 58...
  • Page 65: Spring Cage Connection

    To ensure proper connection of loop cables that are 0,5mm² or less, make sure to push the connector lever fully down with a small screwdriver before inserting the cable. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 59...
  • Page 66: Connections - Overview

    Make sure that the + and – wires are connected correctly according to the table in chapter 9.3.5 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 60...
  • Page 67: Led Connection

    With reference to EN54, the absolute maximum number of protectors on a branch-off (or an open loop) is 32. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 61...
  • Page 68 Make sure that the + and – wires are connected correctly. Branch-off AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 62...
  • Page 69: Alignment Marks On The Protector

    9.4 Alignment Marks on the Protector Before mounting the protector onto the base, observe the alignment marks on the protector shown in the illustration below (Autronica can provide a video showing the mounting of the protector on the protector base).
  • Page 70: Mounting The Protector Onto The Base

    6. Turn the protector clockwise until it is properly fastened (a click will be heard), and make sure that the alignment marks are aligned as shown AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 64...
  • Page 71: Locking/Unlocking The Protector To The Base

    In this case, the locking tool is inserted into the small slot, and the bayonet ring is turned counter-clockwise until it is unlocked. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 65...
  • Page 72: Removing The Protector From The Base

    9.8 Retrofit mounting onto Existing AutroSafe Base BWA-100/BWA-101 Autronica provides several different variants of protectors specifically intended for retrofit purposes (AutroGuard® Retro). These protectors can easily be mounted onto an existing AutroSafe base (BWA-100/BWA-101) similar to chapter 9.5. For dimensions, see chapter 3.6.4.
  • Page 73 Mounting Instructions AutroSafe detector base BWA-100/BWA-101 Protector for retrofit on AutroSafe bases BWA-100/BWA-101 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 67...
  • Page 74: Labeling The Protector Base / Tag Holder

    The protector cover must be removed before use; as soon as • construction work is completed, or before the fire detection loop is in operation. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 68...
  • Page 75: Preparing For Configuration

    AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 69...
  • Page 76: Alternative B - Using The Rip Off Label Inside The Autroguard Base

    10.3.2). If you don’t have a PC and must do this manually, use alternative B described in 10.3.2 Tag name label is to be placed on the tagholder AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 70...
  • Page 77: Alternative A - Using A Qr Code Reader

    If any breaks on the loop’s minus wire or short-circuits are detected, see Troubleshooting, chapter 10.9 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 71...
  • Page 78: Generating An Excel File

    10.3 with Loop Sequence Indexes (LSI) and Serial Numbers (SN) from AS2000. • Save the Excel file as a csv file. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 72...
  • Page 79: Autrosafe Configuration Tool

    (see below) • When the loop is complete and without any errors (breaks/short circuits), click Cancel Click Read Parameters • AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 73...
  • Page 80: Configuration Recommendations

    Below you will find the recommended settings suitable for different applications and rooms with the presence of various nuisance sources. Note that the environment in rooms and applications may vary. The below tables describe Autronica’s recommendations based on general information only. Local considerations need to be made. Nuisance source...
  • Page 81: Hotel Rooms

    MEDIUM Heat response Category DISABLED Configuration of AutroGuard in apartment bedrooms: Operation Class MULTI Sensitivity Class HIGH Heat response Category AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 75...
  • Page 82: Freezers And Cold Stores

    Rooms with early detection of small amounts of smoke: Operation Class MULTI Sensitivity Class HIGH Heat response Category 11.6 Table Overview – Applications/Settings See next pages. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 76...
  • Page 83 The sensitivity is normal, but heat increase will not trigger alarm AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 77...
  • Page 84 Exhaust, Point smoke detectors Multi condensation, dust might not always be the best option for parking garage, due to the AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 78...
  • Page 85 If there is a risk of significant amount of theater smoke reaching the protector, a variant with integrated CO sensor should be used. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 79...
  • Page 86: Configuration For Autrosafe

    (sounder, visual alarm devices, etc.). 12.2 AutroSafe Configuration Tool Requirements The configuration requires the use of AutroSafe Configuration Tool, version 4.11 or higher. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 80...
  • Page 87: Site Configuration System Settings

    - Blink AutroGuard V Series Detector on alarm - Enable AutroGuard V Series Detector LED alive blink Click OK when completed • AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 81...
  • Page 88: Sound And Pulse Patterns

    Sound and Pulse Patterns button Select the tone from the list, then click OK • Refer to chapter 7.3 Sound and Pulse Patterns. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 82...
  • Page 89: Adding System Units

    Select the number of units to be added (for example, 10 units) • Check Auto numbering to automatically number each unit • AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 83...
  • Page 90 Click Add Continue adding units as described above • The example below shows a configuration with several variants of AutroGuard Protectors. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 84...
  • Page 91: Autroguard Default Settings

    Refer to chapter 5.4 Operation Class, 5.5 Sensitivity, 5.6 Heat Response Categories, 5.8 Cover Detection and 14.3.3 Automatic Test Mode. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 85...
  • Page 92: Multi

    From the dropdown lists, select the default properties, then click • 12.5.3 Ex • From the dropdown lists, select the default properties, then click AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 86...
  • Page 93: Ex/S

    12.5.5 Sounder From the dropdown list, select the default sound pressure level • and if the tones are to be mutable AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 87...
  • Page 94: Visual Alarm Device (Vad)

    Type freely selected default postfixes for each sub-unit (these will be added as a postfix to each sub-unit), then click OK AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 88...
  • Page 95: Autroguard Settings For Multiple Protectors

    The “Set AutroGuard Properties” window will appear. Change the properties as specified, the click OK. • The changes will affect all selected protectors. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 89...
  • Page 96: Autroguard Individual Settings

    To enable automatic test mode for a protector, check the checkbox Automatic Test Mode Refer to chapter 14.3.3 Automatic Test Mode. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 90...
  • Page 97: Cover Detection Sensitivity

    Click the dropdown button and select the Heat Reponse Category Refer to chapter 5.6 Heat Response Categories, 5.8 Cover Detection. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 91...
  • Page 98: Operation Classes

    From the system view, select the AutroGuard® Protector • Click the dropdown button for Sensitivity and select the relevant • Sensitivity Refer to chapter 5.5 Sensitivity. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 92...
  • Page 99: Visual Alarm Device (Vad)

    Click the dropdown button for VAD Flash Rate to select the relevant flash rate (1/2 Hz or 1Hz). Refer to chapter 6.6 Flash Rate. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 93...
  • Page 100 Click the dropdown button for VAD Intensity to select one of the • following intensities: Refer to chapter 6.5 VAD Intensity. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 94...
  • Page 101: Sound Pressure Level - Sounders

    Click the dropdown button for Sound Pressure Level and select High or Low Refer to chapter 4.4 Sound Pressure Levels. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 95...
  • Page 102: Matching Protectors/Bases With Autrosafe Configurations

    The basic and critical safety functions will always be maintained. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 96...
  • Page 103: Configuration For Autroprime

    (sounder, visual alarm devices, etc.). 13.2 Autroprime Software Requirements The use of AutroGuard protectors requires Autroprime version 2.2.0 or later (not yet implemented). AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 97...
  • Page 104: Global Settings

    Always take into consideration that a high intensity will draw more current than a low intensity, and high intensity will lead to fewer units per detection loop. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 98...
  • Page 105: Individual Settings

    The Operation Classes that can be chosen depends on the type of point, i.e. MultiSensor with heat, MultiSensor only, Heat only. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 99...
  • Page 106: Heat Response Category Day Mode

    The Operation Classes that can be chosen depends on the type of point, i.e. MultiSensor with heat, MultiSensor only, Heat only. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 100...
  • Page 107: Heat Response Category Night Mode

    (see chapter 14.3.2). • Automatic Test Mode can be enabled (ON) or disabled (OFF) per protector. The default setting is OFF. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 101...
  • Page 108: Use Led Alive Blink

    AutroGuard® protectors with Cover Detection provide the following sensitivity classes: • • Normal High • • Select the relevant Cover Detection Sensitivity for each protector. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 102...
  • Page 109: Testing And Maintenance

    For information on the SelfVerify® 2.0 function, refer to chapter 5.7. Due to the fact that the SelfVerify® 2.0 test is using a calibrated test signal, Autronica Fire and Security considers this to be equal or better than a non-calibrated manual physical test with smoke or test gas.
  • Page 110: Manual Testing

    Testing and Maintenance 14.3 Manual Testing 14.3.1 Introduction Autronica Fire and Security recommends that functional tests of the protector are done automatically by the system itself using the SelfVerify® 2.0 function (refer to chapter 14.1). However, if local regulations require manual testing, a manual test procedure must be carried out.
  • Page 111 Testing and Maintenance AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 105...
  • Page 112: Cleaning Procedure

    “add-on not responding”) if a protector is not replaced within a certain time (the time depends on the size of the detection loop and AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 106...
  • Page 113: Calibrating The Cover Detection Sensor

    If the fault reappears, repeat all steps in the procedure. You can also try to disconnect and reconnect the loop if possible. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 107...
  • Page 114: Method B: Re-Calibrating Using As2000 Loop Diagnostic Tool

    2. Raise the loop by pressing “START” 3. Right-click on the AutroGuard symbol for the affected unit, then click “AutroGuard commands” and the “Calibrate sensors”: AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 108...
  • Page 115 If the fault still appear after trying any of these methods several times, the AutroGuard Protector must be replaced. Register the serial number(s) of the protector(s) and copy the AS2000 logs. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 109...
  • Page 116: Accessories

    The illustrations below show the QR codes on the protector base and the protector, respectively. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 110...
  • Page 117: Was-2000 And As2000 Loop Diagnostic Tool

    WAS-2000. For further information on connections and operation, refer to the User Guide for the Loop Diagnostic Tool on the Autronica product web at www.product.autronicafire.com/products. Part number 116-WAS-2000.
  • Page 118: Air Duct Sampling Unit

    All AutroGuard® protectors can be mounted in an air duct sampling unit to detect smoke in ventilation ducts. Part number Description 116-BWP-143A/AG Air duct sampling unit for AutroGuard® protectors Autronica delivers the following pipe kits in different lengths: Part number Description 116-BJ-358/100 Pipekit L=100 116-BJ-358/150 Pipekit L=150...
  • Page 119: Air Duct Sampling Unit - Stainless Steel

    Part number Description 116-BWP-143A-SS/AG Air duct sampling unit (stainless steel) for AutroGuard® protectors Autronica delivers the following pipe kits in different lengths: Part number Description 116-BJ-358/100 Pipekit L =100mm 116-BJ-358/150 Pipekit L =150mm...
  • Page 120: Conduit Box

    Conduit box AutroGuard 20mm 116-BWP-100/25/AG Conduit box AutroGuard 25mm Spare Parts Description 116-100001400 GLAND - SKINTOP CLICK 25, Light grey AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 114...
  • Page 121: Telescope Removal Tool

    The screen must be connected to earth in one end only. This will normally be at the panel. AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 115...
  • Page 122: Test Gas

    15.10 Test Gas If the use of test gas is required according to local regulations, Autronica Fire and Security recommends the use of smoke test aerosol Solo A10, 150 ml, part number 116-WBJ-5/07. 15.11 Testfire / Solo 365 Test Tool For information on test equipment and instructions, refer to Testifier®’s webpage...
  • Page 123: Appendix

    Appendix 16. Appendix 16.1 UL Regulatory Information Autronica’s variants of the AutroGuard Multicriteria Smoke Detector (named AutroGuard Multicriteria Protector, Series V-430/UL and V-530/UL) certified according to UL standards can only be used together with the AutroSafe Fire Detection System. The UL certification (ETL listing) comprises the following: Smoke and Multi: UL 268, ULCS529 •...
  • Page 124: Index

    Current Consumption · 46 LED on Alarm/LED Alive Blink · 80 Locking the Detector to the Base · 65 Locking Tool · 108 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 118...
  • Page 125 Diagnostic Tool · 109 Wire Insulation Stripping · 58 Wire Routing Arrangement Inside Safety · 5 Detector Base · 57 AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120, 2022-12-09 AutroGuard-Technical-Handbook, Doc-1004339-4, Autronica Fire and Security AS Page 119...

Table of Contents