Download Print this page

Buyers DumperDogg 5531000 Installation Instructions Manual

8 foot poly dump body insert, corrosion resistant powdercoat frame w/polymer insert

Advertisement

Quick Links

Installation/Operation/Instructions
Dump Inserts
5531000 - 8ft. steel dump insert
5531006 - 6ft. steel dump insert
5532000 - 8ft. polymer dump insert
5534000 - 8ft. stainless steel dump insert
5534006 - 6ft. stainless steel dump insert
5532000
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • dumperdogg.com
5531000
5531006
1
9049 Tyler Blvd. • Mentor, Ohio 44060
5534000
5534006

Advertisement

loading
Need help?

Need help?

Do you have a question about the DumperDogg 5531000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Buyers DumperDogg 5531000

  • Page 1 9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • dumperdogg.com Installation/Operation/Instructions Dump Inserts 5531000 - 8ft. steel dump insert 5531006 - 6ft. steel dump insert 5532000 - 8ft. polymer dump insert 5534000 - 8ft.
  • Page 2: Installation

    8. Locate the two holes located in the bottom of the WARNING DumperDogg™ frame at the tailgate area. Ensure there is clearance through the bed of the truck where these holes are • Do not load over 6,000 lbs. located. If there are no wires and or obstructions, use holes as •...
  • Page 3 78" - 80" Fig. 1 20" TRUCK BED ONCE LOCATION OF DUMP BODY DRILL 5/8" HOLE THROUGH IS ESTABLISHED DRILL TWO 5/8" HOLES CROSSMEMBER IN CENTER TO SECURE REAR FRAME TO TRUCK BED OF TRUCK AS SHOWN USE TO POSITION DUMP BODY OR MOUNTING BRACKET DEPENDING ON LOCATION OF DUMP BODY...
  • Page 4 Wiring and Parts List Fig. 3 CONNECT GROUND WIRE FROM HARNESS TO HOLE MARKED "GND" CONNECT BLACK WIRE FROM CONTROLLER HERE CONNECT RED WIRE FROM CONTROLLER HERE CONNECT GREEN WIRE CONNECT POWER WIRE (RED) FROM CONTROLLER HERE CONNECT WHITE WIRE FROM HARNESS TO THIS POST FROM CONTROLLER HERE Bill of Materials...
  • Page 5: Bill Of Materials

    Frame Unit Common for Polymer and Steel Units SEE DETAIL A Connect Negative (-) cable to one of these bolts to ground unit Bill of Materials item part no. qty. description — Cover, Pump DETAIL A PU642TP Pump 3003286 Bumper 3013967 3014379 Pin Short 3014380 Pin Long...
  • Page 6 Parts List 8ft . & 6ft. Steel & Stainless Steel Bed Insert Bill of Materials item part no. qty. description 3015534 (8ft.) Hopper, Steel 3017044 (6ft.) Hopper, Steel 3016602 (8ft.) Hopper, Stainless Steel 3017093 (6ft.) Hopper, Stainless Steel 3014800 Tailgate, Steel 3017117 Tailgate, Stainless Steel 3000420 Pin 3000420SS Pin, Stainless Steel 3000422 Spring 3000422SS Spring, Stainless Steel — Roll Pin, 7/32" X 1-1/2"...
  • Page 7 Parts List 8ft. Polymer Bed Insert Bill of Materials item part no. qty. description 3013970 Hopper 3014013 Screen 3014800 Tailgate 3014032 End Cap 3014030 Inner Panel 3014028 Washer Plate 3000420 – Roll Pin, 7/32" X 1-1/2" 3000422 Spring Options item part no. qty. description – 5531050 Side Wall Extensions – DTR4510 Roll Tarp Kit, 4.6ft x 10ft –...
  • Page 8 30 days after such defect is discovered, and returned part(s) are found to be defective Buyers Products Company. Prior to submitting a claim, your DumperDogg™ must be registered with Buyers Products.

This manual is also suitable for:

Dumperdogg 5531006Dumperdogg 5532000Dumperdogg 5534000Dumperdogg 5534006