Buyers 8890700 Installation & Operation Instructions

Installation and Operation Instructions
LED Flexible Strobe Lights
Kit Includes the Following:
• Lighthead with 9.38in cord
• 2X M3.0x12mm long self-tapping screws
• 2X 3.5mm screw washer
• 2X snap caps
• Double-sided adhesive mounting pad with alcohol pre pad
• Curvature template
• Instructions
Part Number LED Qty. and Colors
8890700 6 (6 Amber)
8890702 12 (6 Amber/6 Clear)
8890708 12 (6 Blue/6 Amber)
8890709 12 (6 Green/6 Amber)
• Max. Current: .64A
• Max. Power: 7.68W
WIRING CODE
Order of Precedence: Mode3 > Mode2 > Mode1
BLACK: To Chassis Ground (-)
RED: +VDC for Warning Mode 1 (fuse @ 1A)
- Single Color: Default FP#2
- Dual Color: Default Color Mode – Color 1, FP#1
WHITE: +VDC for Warning Mode 2 (fuse @ 1A)
- Single Color: Default FP#1
- Dual Color: Default Color Mode – Color 2, FP#1
RED & WHITE*: +VDC for Warning Mode 3 (fuse @ 1A)
*Only present on Single-Color models
- Default FP#18
GREEN*: +VDC for Warning Mode 3 (fuse @ 1A)
*Only present on Dual-Color models
- Default Color Mode – Color 1 alt. 2, FP#1
YELLOW: Flash Patterns & Synchronization
- Connect YELLOW wires of all light heads together
for synchronization (All heads must be set to the
same pattern)
- Can synchronize up to 20 lights
WARNING
Do not look directly into LEDs while in operation; this may
cause momentary blindness and/or eye damage.
WARRANTY
Buyers Products Co. warrants all truck/trailer hardware manufactured or distributed by
it, to be free from defects in material and workmanship for a period of one year from
date of shipment. Parts must be properly installed and used under normal conditions.
Any product which has been altered, including modification, misuse, accident or lack
of maintenance will not be considered under warranty. Normal wear is excluded. The
sole responsibility of Buyers Products Co. under this warranty is limited to repairing or
replacing any part or parts which are returned, prepaid, and are found to be defective
by Buyers Products Co. Authorization from Buyers Products Co. must be obtained
before returning any part. No charges for transportation or labor performed on Buyers'
products will be allowed under this warranty.
Screw Holes Avg. Current Avg. Current
Spacing (in) @ 12VDC @ 24VDC
4.62 .32 .16
4.62 .32 .16
4.62 .32 .16
4.62 .32 .16
OPERATION MODE
Flash Patterns:
While activating a warning mode, momentarily apply +VDC to YELLOW
wire or change pattern switch:
• Once for next pattern.
• Quick three times to reset to FP#1.
FP# Flash Patterns
1 DOUBLE [2Hz]
2 SINGLE [2Hz]
3 TRIPLE [2Hz]
4 QUAD [2Hz]
5 RANDOM
6 STEADY EF*
7 SINGLE [SAE][CA13]
8 DOUBLE [SAE]
9 TRIPLE [SAE]
10 QUAD [SAE]
11 QUINT [SAE]
12 MEGA
13 GIGA
14 ULTRA [SAE]
15 SINGLE-QUAD
16 SINGLE H/L
• FP#22-31 will always operate in dual color.
• * = For use with external flash controller
• # = Inverted color mode
Shortcut Setting for Steady EF (External Flasher):
"Steady EF" Flash Pattern shortcut for independent color control via
an external flasher. Momentarily apply +VDC to YELLOW wire for 3 to
4 seconds (Visual feedback ON->OFF->ON) while activating a warning
mode. Each warning mode will simultaneously be set to the following:
• Warning Mode 1 = FP#6 Steady EF
• Warning Mode 2 = FP#6 Steady EF
• Warning Mode 3 = FP#21 Off
SETTING MODE
1. SETTING MODE lets you change Synchronization & Color Mode Settings
for each Warning Mode, as well as reset all modes to Factory Default Settings
at the same time. Apply +VDC to Warning Mode Wire (RED or WHITE or
RED+WHITE or GREEN) and YELLOW wires simultaneously, then remove
YELLOW wire to enter SETTING MODE for the following settings.
2. Save and exit SETTING MODE by disconnecting the power.
1
www.buyersproducts.com
Phone (440) 974-8888
Fax 800-841-8003
FP# Flash Patterns
17 SINGLE-TRIPLE-QUINT
18 STEADY SCENE
19 CRUISE
20 SWEEP SINGLE TA
21 OFF
22 SINGLE-SINGLE
23 DOUBLE-DOUBLE
24 TRIPLE-TRIPLE MID
25 TRIPLE-TRIPLE FAST
26 QUINT-TRIPLE
27 7-1 FLASH
28 7-1 FLASH#
29 QUAD-SINGLE
30 QUAD-SINGLE#
31 QUINT-QUINT