Related Manuals for Avalue Technology VNS-10WAD
Summary of Contents for Avalue Technology VNS-10WAD
- Page 1 VNS-10WAD 10.1" Ultra Slim Panel PC with Intel® Processor N50 Quick Reference Guide Ed – 12 May 2025 Copyright Notice Copyright © 2025 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No. E2017VNWDA0R...
- Page 2 VNS-10WAD Document Amendment History Revision Date Comment May 2025 Avalue Initial Release 2 VNS-10WAD Quick Reference Guide...
-
Page 3: Declaration Of Conformity
For detailed information, please always refer to the electronic user's manual. Copyright Notice © 2025 by Avalue Technology Inc. All rights are reserved. No parts of this manual may be copied, modified, or reproduced in any form or by any means for commercial use without the prior written permission of Avalue Technology Inc. - Page 4 ㆍDescription of your software (operating system, version, application software, etc.) ㆍA complete description of the problem ㆍThe exact wording of any error messages To receive the latest version of the user’s manual; please visit our Web site at: www.avalue.com 4 VNS-10WAD Quick Reference Guide...
- Page 5 On the other hand, if the new product defect is resulting from incorrect configuration or erroneous use by the user instead of any problem of the hardware itself, the customer will also be requested to pay for relevant handling fees. VNS-10WAD Quick Reference Guide...
- Page 6 Lacking detailed statement of fault steps also makes the problem hard to be identified, sometimes resulting in second-time repairs. 6 VNS-10WAD Quick Reference Guide...
- Page 7 Product has been altered or its label of the serial number has been torn off. • Product functionality issues resulting from improper use by the user, unauthorized dismantle or alteration, unfit operation environment, improper maintenance, accident VNS-10WAD Quick Reference Guide...
- Page 8 If the customer demands an additional maintenance analysis report, a service fee of various level will be charged depending on the warranty status. In case the analysis result shows that the defect attributes to Avalue’s faulty design or process, the analysis fee will be exempted. 8 VNS-10WAD Quick Reference Guide...
-
Page 9: Safety Instructions
9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to VNS-10WAD Quick Reference Guide... - Page 10 The equipment has obvious signs of breakage. 14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 15. Equipment intended only for use in a RESTRICTED ACCESS AREA. 10 VNS-10WAD Quick Reference Guide...
-
Page 11: Explanation Of Graphical Symbols
A NOTE provides additional information intended to avoid Note inconveniences during operation. Direct current. Alternating current Stand-by, Power on FCC Certification CE Certification Follow the national requirements for disposal of equipment. Stacking layer limit This side up VNS-10WAD Quick Reference Guide 11... - Page 12 VNS-10WAD Fragile Packaging Beware of water damage, moisture-proof Carton recyclable Handle with care Follow operating instructions of consult instructions for use. 12 VNS-10WAD Quick Reference Guide...
-
Page 13: Disposing Of Your Old Product
EXPLOSION ou une fuite de liquide ou de gaz inflammable. - UNE BATTERIE soumise à une pression d'air extrêmement basse pouvant entraî ner une EXPLOSION ou une fuite de liquide ou de gaz inflammable. VNS-10WAD Quick Reference Guide 13... -
Page 14: Table Of Contents
Rear View ..........................19 1.5 System Dimensions ....................21 1.6 VESA Mounting ....................... 22 Hardware Configuration ..................25 2.1 VNS-10WAD connector mapping ................26 2.1.1 Serial port connector (COM1) ....................26 2.2 Powering On the System ..................27 Installation ......................28 Drivers Installation .................... -
Page 15: Getting Started
1.2 Packing List Before installation, please ensure all the items listed in the following table are included in the package. Item Description Q’ty VNS-10WAD Panel PC AC/DC adapter 12V/5A 90 Screw Type (Option) power cord (Option) VNS-10WAD Quick Reference Guide 15... - Page 16 VNS-10WAD Purposes and Applications VNS-10WAD is used the Intel Atom® X-series (Elkhart Lake platform), which has stronger performance and lower power consumption. it also inherits from ARC-series strength, Modularized, Flexible Expansion, Reliability and Stability. ARC series have been passed stricter vibration and shock testing. It can be used on extreme environment like manufacture or factory.
-
Page 17: System Specifications
CE, FCC Class B Air 8Kv / Contact 4Kv Sine Vibration test (Non-operation) Reference IEC60068-2-6 Testing procedures. Vibration Test Test Fc : Vibration sinusoidal 1. Test Acceleration : 2G 2. Test frequency : 5~500 Hz VNS-10WAD Quick Reference Guide 17... - Page 18 Operating 0°C ~ 40°C, DC in Mode Temperature 0°C ~ 35°C, Powered LAN Mode Operating Humidity 40°C @ 95% Relative Humidity, Non-condensing Storage -10°C ~ 60°C Temperature Note: Specifications are subject to change without notice. 18 VNS-10WAD Quick Reference Guide...
-
Page 19: System Overview
Quick Reference Guide 1.4 System Overview 1.4.1 Front View Display Brightness Volume Power on/off Up/down Up/down on/off 1.4.2 Rear View VNS-10WAD Quick Reference Guide 19... - Page 20 VNS-10WAD Connectors Label Function Note DC IN DC-IN power connector RJ-45 Ethernet Serial port connector 2 x USB 3.0 connector Headphone Headphone jack 20 VNS-10WAD Quick Reference Guide...
-
Page 21: System Dimensions
Quick Reference Guide 1.5 System Dimensions (Unit: mm) VNS-10WAD Quick Reference Guide 21... -
Page 22: Vesa Mounting
VNS-10WAD 1.6 VESA Mounting Step1. Insert and fasten 4 screws on each side of VNS-10WAD to secure VESA Mount. 22 VNS-10WAD Quick Reference Guide... - Page 23 Quick Reference Guide Step2. Insert and fasten 4 screws on each side of the monitor to secure VESA Mount. VNS-10WAD Quick Reference Guide 23...
- Page 24 VNS-10WAD Step3. Slide VNS-10WAD onto the Monitor. 24 VNS-10WAD Quick Reference Guide...
-
Page 25: Hardware Configuration
Quick Reference Guide 2. Hardware Configuration Note: If you need more information, please visit our website: www.avalue.com VNS-10WAD Quick Reference Guide 25... -
Page 26: Vns-10Wad Connector Mapping
VNS-10WAD 2.1 VNS-10WAD connector mapping 2.1.1 Serial port connector (COM1) * Default Note: RS-422 supports RS232 (RS422/RS485 selected by Signal BIOS) RS-232* Signal DCD# RS-485 Signal DATA- DTR# DATA+ DSR# RTS# CTS# 26 VNS-10WAD Quick Reference Guide... -
Page 27: Powering On The System
Step 3: Locate the power button on the product. Step 4: Switch on the power button can turn on the system. Keep holding the power button on can force shutdown the PC. Power Button Power Input Connector VNS-10WAD Quick Reference Guide 27... -
Page 28: Installation
VNS-10WAD 3. Installation 28 VNS-10WAD Quick Reference Guide... - Page 29 ⚫ Anti-static Discharge: If a user open the rear panel of the flat bezel panel PC, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear an anti-static wristband. VNS-10WAD Quick Reference Guide 29...
-
Page 30: Drivers Installation
HID touch digitizer built-in driver in Windows 10 or later. Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen. 30 VNS-10WAD Quick Reference Guide... -
Page 31: Install Chipset Driver
Windows 11 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Install. Step 4. Click Restart. Step1. Click Next. Step 2. Click Accept. VNS-10WAD Quick Reference Guide 31... -
Page 32: Install Vga Driver
Continue to go on. Step 3. Click Accept. Step 1. Click Begin installation. Step 4. Click Start. Step 2. Click I agree. Step 5. Click Finish to complete setup. 32 VNS-10WAD Quick Reference Guide... -
Page 33: Install Me Driver
Continue to go on. Step 3. Click Next. Step 1. Click Next to continue setup. Step 4. Click Finish to complete setup. Step 2. Click Next. VNS-10WAD Quick Reference Guide 33... -
Page 34: Install Audio Driver
All drivers can be found on the Avalue Official Website: www.avalue.com. Note: The installation procedures and screen shots in this section are based on Windows 11 operation system. Step 1. Click YES. Step 2. Click Finish to complete setup. 34 VNS-10WAD Quick Reference Guide... -
Page 35: Install Lan Driver
Windows 11 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Finish to complete setup. Step 1. Click Install Drivers and Software. Step 2. Click Install. VNS-10WAD Quick Reference Guide 35... -
Page 36: Install Nfc Driver
Windows 11 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Close to complete setup. Step 1. Click Install. Step 2. Click Next. 36 VNS-10WAD Quick Reference Guide... -
Page 37: Install Hid Driver
If the warning message appears while the installation process, click Continue to go on. Step 3. Click Next. Step 1. Click Next to continue setup. Step 4. Click Finish to complete setup. Step 2. Click YES. VNS-10WAD Quick Reference Guide 37... -
Page 38: Install I2C Driver
Windows 11 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Close to complete setup. Step 1. Click Install. Step 2. Click Next. 38 VNS-10WAD Quick Reference Guide... -
Page 39: Install Sio Driver
Continue to go on. Step 3. Click Next. Step 1. Click Next to continue setup. Step 4. Click Next. Step 5. Click Finish to complete setup. Step 2. Click Next. VNS-10WAD Quick Reference Guide 39... -
Page 40: Install Wifi Driver
Note: The installation procedures and screen shots in this section are based on Windows 11 operation system. If the warning message appears while the installation process, click Continue to go on. Step 1. Click Finish to complete setup. 40 VNS-10WAD Quick Reference Guide... -
Page 41: Install Uart Driver
Windows 11 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Finish to complete setup. Step 1. Click Next to continue setup. Step 2. Click Next. VNS-10WAD Quick Reference Guide 41... -
Page 42: Maintenance & Troubleshooting
System Maintenance Introduction If the components of the product fail they must be replaced. Please contact the system reseller or vendor to purchase the replacement parts. Please follow the safety precautions outlined in the sections that follow 42 VNS-10WAD Quick Reference Guide... -
Page 43: General Safety Precautions
Drop the device against a hard surface. ⚫ Strike or exert excessive force onto the LCD panel. ⚫ Touch any of the LCD panels with a sharp object. ⚫ In a site where the ambient temperature exceeds the rated temperature. VNS-10WAD Quick Reference Guide 43... -
Page 44: Anti - Static Precautions
This reduces the possibility of ESD damage. ⚫ Only handle the edges of the electrical component. When handling the electrical component, hold the electrical component by its edges. Please ensure the following safety precautions are adhered to at all times. 44 VNS-10WAD Quick Reference Guide... -
Page 45: Maintenance And Cleaning
Never drop any objects or liquids through the openings of the device. ⚫ Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the device. ⚫ Avoid eating, drinking and smoking within vicinity of the device. VNS-10WAD Quick Reference Guide 45... -
Page 46: Cleaning Tools
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas. ⚫ Foam swabs: Whenever possible, it is best to use lint free swabs such as foam swabs for cleaning. 46 VNS-10WAD Quick Reference Guide... -
Page 47: Basic Troubleshooting
No Console Input Devices are found Flash update is failed Typically for development use. The beep code is generated when platform cannot be reset because reset protocol is not available. Platform PCI resource requirements cannot be met VNS-10WAD Quick Reference Guide 47... -
Page 48: Product Application
Avalue technical support team, or Avalue customer service representatives for further information. Feel free to inquire about this supplementary resource to enhance your understanding of the Watchdog Timer and Digital I/O (DIO) Application for optimal utilization of your Panel 48 VNS-10WAD Quick Reference Guide... -
Page 49: Operating The Device
Avalue technical support team, or Avalue customer service representatives. These professionals can provide tailored guidance and assistance to address any unique needs related to Multi-Touch mode adjustments. VNS-10WAD Quick Reference Guide 49...
Need help?
Do you have a question about the VNS-10WAD and is the answer not in the manual?
Questions and answers