INTERSPIRO Incurve User Manual
Hide thumbs
Also See for Incurve:
- User manual (73 pages) ,
- User manual (60 pages) ,
- User manual (72 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for INTERSPIRO Incurve
Summary of Contents for INTERSPIRO Incurve
- Page 1 ENGLISH Incurve User Manual 55167H01 2025-05...
- Page 2 Copyright © 2022 Interspiro This publication contains or refers to proprietary information which is protected by copyright. All rights are reserved. Interspiro® and Divator® are registered trademarks belonging to Interspiro. This publication may not be copied, photocopied, reproduced, translated, or converted to any electronic or machinereadable form in whole or in part, without prior written approval from Interspiro.
-
Page 3: Table Of Contents
TABLE OF CONTENT 1 SAFETY NOTICE ................10 2 CYLINDER COUPLINGS ..............12 3 CYLINDER MOUNTING ..............13 4 ADJUSTING THE HARNESS ............14 5 DONNING ..................14 6 CHECKING BEFORE USE ..............15 7 REMOVING THE APPARATUS ............15 8 CLEANING AND DISINFECTING ............ -
Page 10: Safety Notice
Individuals with beards or large sideburns may not obtain an adequate seal. The apparatus must be maintained, serviced and tested as described in this user manual, Interspiro service manuals and Interspiro test instructions. INTERSPIRO IS NOT RESPONSIBLE FOR... - Page 11 Exposure to extreme conditions may require measures other than those described in this user manual. Interspiro’s responsibility and warranty conditions are not extended or affected by these safety regulations. The breathing air with which the cylinders are charged must meet the requirements according to EN 12021, being free from oil, toxic substances and having low humidity.
-
Page 12: Cylinder Couplings
CYLINDER COUPLINGS There are three different types of couplings on the regulator unit for coupling with cylinder. These three are described below. When mounting the regulator unit in the cylinder, follow the description for the particular configuration you have on your equipment. -
Page 13: Cylinder Mounting
CYLINDER MOUNTING SINGLE CYLINDER Check that the cylinder strap buckle is positioned as close to the backplate as possible. Place the cylinder on the backplate. [Fig. 1] Connect the regulator unit and cylinder according to chapter 2. Fasten cylinder strap around the cylinder and hook together with the buckle [Fig. -
Page 14: Adjusting The Harness
Fit the holes of the cylinder bracket onto the guide washers and push the backplate away from you until the harness clicks in position. Check that the cylinder pack is mounted properly by lifting the harness carefully in the upper and lower part of the backplate. -
Page 15: Removing The Apparatus
In environments where open storage with prolonged exposure to direct water spray is unavoidable, such as on vessels or in shoreline areas, the protective plug (Interspiro item No: 34830-51) for the whistle must be fitted. The plug’s attached string should... -
Page 16: Extra Air Connection
be securely fastened to a fixed object at the storage location, allowing it to be automatically detached when the SCBA is removed for donning, ensuring the unit is immediately ready for use. 10. EXTRA AIR CONNECTION Some models are equipped with an extra air connection which can be used to: connect to a chemical suit ventilation system connect a rescue hose between two apparatus connect an extra mask... -
Page 17: Usage With Airline System
European standard and classification Year of manufacture 14. SERVICE AND TESTING SCHEDULE Service and testing must as a minimum be carried out according to Interspiro’s Service and Testing Schedule, or according to local requirements. Visit www.interspiro.com for the latest version. -
Page 18: Cbrn
15. CBRN CBRN approval is only valid when Incurve BA is combined with Inspire mask in EPDM + Inspire breathing valve with CBRN coated diaphragm.
Need help?
Do you have a question about the Incurve and is the answer not in the manual?
Questions and answers