Bizerba VSI330 F Instruction Manual
  1. Manuals
  2. Brands
  3. Bizerba Manuals
  4. Kitchen Appliances
  5. VSI330 F
  6. Instruction manual
Bizerba VSI330 F Instruction Manual

Bizerba VSI330 F Instruction Manual

Hide thumbs Also See for VSI330 F:
Table of Contents

Advertisement

Quick Links

Download this manual
Slicer
VSI330 F / VSI330 F W
VSI330 F T / VSI330 F TW
Instruction manual NSF
38065447007 en-US

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VSI330 F and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bizerba VSI330 F

Summary of Contents for Bizerba VSI330 F

  • Page 1 Slicer VSI330 F / VSI330 F W VSI330 F T / VSI330 F TW Instruction manual NSF 38065447007 en-US...
  • Page 2 Alle Rechte vorbehalten All rights reserved Tous droits réservés Reservados todos los derechos Tutti i diritti riservati Bizerba SE & Co. KG, 72336 Balingen Postfach 10 01 64 72301 Balingen, Germany Telephone (+49 7433) 12-0, Fax (+49 7433) 12-2696 E-mail: marketing@bizerba.com Internet: www.bizerba.com...

  • Page 3: Table Of Contents

    Instruction manual NSF VSI / VSI W / VSI T / VSI Table of Contents Table of Contents About these instructions ..................  Safe-keeping ..................  Target group ..................  Symbols used ..................  Warnings ....................  About this machine .....................   Intended use..................
  • Page 4 Instruction manual NSF VSI / VSI W / VSI T / VSI Table of Contents Product fixation device .................   Operation......................  Log in operator ..................  Main page (individually configured operator page).......   Navigation between the pages .............   Parameter page..................
  • Page 5 Instruction manual NSF VSI / VSI W / VSI T / VSI Table of Contents Technical data......................   106 Dimensions VSI / VSI W...............   106 Dimensions VSI T.................   107 Dimensions VSI TW ................  108 Technical data ..................  110 Power supply ..................

  • Page 6: About These Instructions

    The minimum age of the operating personnel by German law is 14. Other age limits may ap- ply according to the corresponding national regulations. Therefore the operating company must check the legislation at the place of machine installation. Installation, maintenance and repair works must be performed by Bizerba authorized special- ists only. Symbols used Various symbols are used in these instructions.

  • Page 7: Warnings

    Instruction manual NSF VSI / VSI W / VSI T / VSI About these instructions Information This information is intended for better understanding. Warnings Warnings are divided into danger levels by the signal word above the warning symbol. Structure of warnings and meaning of signal words are described in these instructions as fol- lows.

  • Page 8: About This Machine

    Note: If cheese is the main product being sliced, we recommend using a special cheese blade. Slicing of other materials requires prior written approval by Bizerba product management. Non-permitted product The following may not be sliced due to risk of injury and damage: –...

  • Page 9: Machine Description

    VSI330 F W = machine with depositing table, scale (W), 400 mm or 600 mm carriage VSI330 F T = machine with conveyor belt (T), 400 mm or 600 mm carriage VSI330 F TW = machine with conveyor belt (T), scale (W), 400 mm or 600 mm carriage All versions are available with a mobile stand.

  • Page 10: Names Of Components Vsi W

    Instruction manual NSF VSI / VSI W / VSI T / VSI About this machine Vibration The total vibration of the items, which get into contact with hand and arm is below 2.5 m/s and therefore below the required limited value. 2.2.1 Names of components VSI W Fig. 1: Names of components VSI W...
  • Page 11 Instruction manual NSF VSI / VSI W / VSI T / VSI About this machine The machine is available in different versions. The figure shows an example: Blade guard ring Blade Blade cover Product holder complete with remnant holder Product fixation device, horizontal Feeding carriage Carriage Identification plate...

  • Page 12: Names Of Components Vsi T

    Instruction manual NSF VSI / VSI W / VSI T / VSI About this machine 2.2.2 Names of components VSI T Fig. 2: Names of components VSI T 12 / 118 38065447007 en-US...
  • Page 13 Instruction manual NSF VSI / VSI W / VSI T / VSI About this machine The machine is available in different versions. The figure shows an example: Blade guard ring Blade Blade cover Product fixation device, vertical Product holder complete with remnant holder Carriage Carriage guide Display and operating unit with ON/OFF switch at the bottom of the machine housing...

  • Page 14: Names Of Components Vsi Tw

    Instruction manual NSF VSI / VSI W / VSI T / VSI About this machine 2.2.3 Names of components VSI TW Fig. 3: Names of components VSI TW 14 / 118 38065447007 en-US...

  • Page 15: Accessories

    Display and operating unit with ON/OFF switch at the bottom of the machine housing (optionally on top) 2.2.4 Accessories Only use the original Bizerba spare parts and accessories in order to en- sure safe and trouble-free operations. standard – Instruction manual –...

  • Page 16: Warranty

    To ensure that the machine is recycled environmentally friendly, return the machine to the manufacturer or the dealer after intended use has expired. Naturally, Bizerba and its dealers will take back free of charge old machines no longer in op- eration.

  • Page 17: Safety Instructions

    – Protective devices may not be removed, modified or bypassed. DANGER Open the electrical installation area! danger to life due to electric current – The electrical installation area may only be opened by Bizerba Ser- vice. – Pull power plug before moving the machine. WARNING Unauthorized persons! Serious injuries to fingers and hands and damage to health.

  • Page 18: Safety Instructions For Transport And Installation

    Destruction of electric components, fire hazard. – Do not connect the machine to the power supply if the power supply data does not correspond to the machine's connection values. Mains data must be identical. – Inform Bizerba Customer Service. 18 / 118 38065447007 en-US...

  • Page 19: Safety Instructions During Operation, Slicing

    Instruction manual NSF VSI / VSI W / VSI T / VSI Safety instructions Safety instructions during operation, slicing DANGER Tipping hazard in case of overload! This may result in serious injuries and damage to property. – Operate machine on stand only if its weight rests on the feet and the casters are locked.

  • Page 20: Safety Instructions For Sharpening, Cleaning

    – Check if the machine is complete before it is re-started. – Check if components are positioned correctly and firmly. – Only use original Bizerba spare parts and accessories. Protective and safety devices – Blade guard ring, stationary, cannot be removed –...

  • Page 21: System Design Related Residual Hazards

    Instruction manual NSF VSI / VSI W / VSI T / VSI Safety instructions – Sharpening program, locked machine setting Remaining risks that cannot be excluded by technical measures: – Risk of tripping/slipping if the work area is not kept tidy. –...
  • Page 22 Instruction manual NSF VSI / VSI W / VSI T / VSI Safety instructions Fig. 5: VSI TW 22 / 118 38065447007 en-US...

  • Page 23: Installation

    Instruction manual NSF VSI / VSI W / VSI T / VSI Installation Installation Unpacking instructions When transporting the machine, wear shoes with toe caps and use suit- able lifting devices. At least four people are needed to move the machine. Weight of machine is higher than 100 kg.

  • Page 24: Transport And Storage

    4.3.1 Installation requirements Safe operation of the slicer within the standards and guidelines is ensured on the Bizerba stand. Stand and slicer bear a CE mark (or UL/cUL mark within the area of application). The integrated scale can only be reliably used with the Bizerba stand.

  • Page 25: Position On Stand

    500 mm if machine is installed on a stand. 4.3.2 Position on stand Installation as well as instruction on how to operate the stand are initially provided by the Bizerba service. DANGER Tipping hazard when improperly installed! This may result in serious injuries and damage to property.
  • Page 26 Instruction manual NSF VSI / VSI W / VSI T / VSI Installation Put weight on mobile stand's feet by lift- ing the wheels. Lock casters. CAUTION! Crushing hazard when lower- ing the wheels. Use bracket to lift and lower wheels. Position machine on stand.

  • Page 27: Electrical Connection

    Instruction manual NSF VSI / VSI W / VSI T / VSI Installation 4.3.3 Electrical connection Information on identification plate Bizerba logo BIZERBA Machine type Model VSI330 F / VSI330 F W / VSI330 F T / VSI330 F TW Machine description Slicer Machine number Production code X-.. IP rating...

  • Page 28: Start-Up

    With severely contaminated mains supplies (e.g. when "thyristor-controlled systems" are used) measures must be taken on-site to suppress interferences, e.g.: – A separate supply line must be planned for Bizerba machines. – In problem cases, install capacitively decoupled isolating transformers or other suppres- sors into the supply mains prior to Bizerba machines.

  • Page 29: Switching The Machine Off

    Instruction manual NSF VSI / VSI W / VSI T / VSI Installation Machine carries out a system check. On the information bar the required steps are listed. Successfully completed steps receive a check mark. Press <Execute> on the display and op- erating unit after initialization.

  • Page 30: Machine And Operating Elements

    Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Machine and operating elements Display and operating unit The slicers are operated via a touch screen. Fig. 12: Display and operating unit <ON switch> (green) LED (white) lights up when machine is switched on <OFF switch>...
  • Page 31 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Navigation bar: Home After pressing the icon, the individually configured operator page (main page) comes up on the touchscreen. Parameter After pressing the icon, the operator page with all parameters (parameter page) comes up on the touchscreen.
  • Page 32 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Depositing type Selectable are: – Stacking – Shingling lengthwise – Shingling crosswise – Circular pattern – Shaving – Vector graphic Filter characteristic in the search mask. PLU menu: Save PLU Save PLU as...

  • Page 33: Parameter Symbols

    Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements 5.2.1 Parameter symbols Information on product Product ID Name of product Product height Specifies the product height in mm. Required for the calculation of the depositing pattern. Product width Specifies the product width in mm.
  • Page 34 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Depositing area length Specifies the length of a package in mm. Depositing area height Specifies the height of a package in mm. Information on slicing program PLU No.
  • Page 35 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Product feed offset Current slice thickness is changed by this value. Staggered stack crosswise Specifies the offset by means of which every second slice is deposited to the left (if product dimensions are entered cor- rectly).
  • Page 36 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Number of rows crosswise Specifies the number of shingle rows deposited in running di- rection in a portion. Row = shingling crosswise Number of rows lengthwise Specifies the number of shingle rows deposited crosswise to the running direction in a portion.
  • Page 37 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Other parameters Gauge plate offset Clearance which is additionally needed for the gauge plate to open or close during slicing. Light sensor Activation switch for light sensor at conveyor belt. Off/On Blade speed Specifies the speed of rotation of the blade in U/min.

  • Page 38: Anchor Symbol

    Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements 5.2.2 Anchor symbol The small colored anchor on the tiles of the parameters <Number of slices>, <Slice thickness>, <Shingling length> or <Shingling distance> means that the corresponding param- eter is fixed.

  • Page 39: Depositing Patterns

    Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements The shingling distance is fixed. In order to obtain the preset shingling dis- tance, the shingling length is reduced or in- creased. If the anchor is set to shingling distance, then the shingling length can not be changed.
  • Page 40 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Fig. 17: Depositing pattern stack Depositing offset lengthwise Depositing offset crosswise Row spacing lengthwise, stacks Row spacing crosswise, stacks Product height Product width Shingling lengthwise The sliced product is offset on top of each other and forms one or more shingles parallel to the blade.
  • Page 41 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Fig. 18: Depositing pattern shingling lengthwise Depositing offset lengthwise Depositing offset crosswise Row spacing lengthwise, shingles lengthwise Row spacing crosswise, shingles lengthwise Product height Product width Shingling distance Shingling length Shingling crosswise (not available for all variants)
  • Page 42 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements The overall pattern may consist of several shingles crosswise and equals a portion. The de- positing table has room for only one portion. Several parameters influence the look of the depositing pattern: Fig. 19: Depositing pattern shingling crosswise Depositing offset lengthwise Depositing offset crosswise...
  • Page 43 Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Note: In case of many layers, the max. stack height could be exceeded without the machine switching off. In this case, the number of layers has to be manually reduced.

  • Page 44: Paper Holder

    Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Shaving The sliced product forms a pile of loosely falling slices. For this purpose you need a shaving deflector (optional accessories). In order to mount the shaving deflector to the chain frame the depositing arm must first be disassembled.

  • Page 45: Product Fixation Device

    Instruction manual NSF VSI / VSI W / VSI T / VSI Machine and operating elements Removing of deposited portions and paper: Using your thumb, press lever slightly to the right; at the same time pull top-most piece of paper with portion under the open holders. Release lever.

  • Page 46: Operation

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Operation Log in operator - Machine is switched on, system check was successful. [} 28] Click into the operator field. The input keyboard is shown. Enter name of operator. Regular operators can also select the name via <Touch-Down>.

  • Page 47: Main Page (Individually Configured Operator Page)

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Main page (individually configured operator page) After successful system check and operator login the main page is loaded with the parame- ters which were saved last before the machine was switched off. The status bar on top shows the progress of the slicing process, registered operators, warnings and pending orders.

  • Page 48: Navigation Between The

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Navigation between the pages By tapping the icons of the navigation bar you may switch between the pages. Using your finger, wipe from right screen edge to center. Tap the arrow.

  • Page 49: Tile Manager

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Tap and hold tile for a while. Checkmark. The parameter is displayed on the main page. Remove checkmark. The parameter is not displayed on the main page. Fig. 32: Tile manager Tile manager The tile manager includes the tile settings.

  • Page 50: Search Mask

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Loading and saving images: To open PLU menu tap the arrow on the information bar. Wipe in arrow direction. The input mask opens. Fig. 34: PLU menu - USB stick is plugged in the display and operating unit.

  • Page 51: Settings

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Saved PLUs can be filtered according to: 1. PLU No. 2. PLU name 3. Product width 4. Product height 5. Depositing type 6. Target weight Fig. 37: Search mask By tapping the corresponding text field the suitable input keyboard opens at the lower screen edge.

  • Page 52: User Management

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Here, various settings may be performed with relevant authorization. Settings concerning machine, software, op- erator and messages can be displayed and edited. Tap a tile. The relevant menu appears on the touch screen.
  • Page 53 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation User groups Tap <Groups> Here, user groups can be created. For each group one user is created as de- fault value. Name corresponds to the level name. Fig. 43: Groups Login settings Tap <Settings>...

  • Page 54: Software Settings

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation 6.8.2 Software settings (not available for all variants) Call up via the setting in the navigation bar. The VSI will be integrated in the network as a Client and communicates via nonsecure con- nections.

  • Page 55: Licensing Of Additional Functions

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Creating a backup: Press <PLU backup>. Select storage space (flash memory, USB, SD card, network drive). File name assigned. Alphanumeric char- acters (upper case, lower case, no um- lauts), hyphen, underscore and space are permitted.

  • Page 56: Brain2 Function

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Call up via the setting in the navigation bar. Press <Licensing>. Enter and save license code. The functions for which the licenses were ac- quired are activated. Fig. 50: Licensing Scroll downwards.
  • Page 57 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Call up via the setting in the navigation bar. Press <BRAIN2>. Tick checkbox "Use BRAIN2 function". Fig. 52: Use BRAIN2 function Perform configuration settings. – IP address server (UDP) –...

  • Page 58: Cloud Function

    6.8.6 Cloud function (not available for all variants) Call up via the setting in the navigation bar. Press <Bizerba Cloud>. Tick checkbox "Use Cloud function" Fig. 54: Use Cloud function Perform configuration settings according to requirements of the cloud. Save configuration settings.
  • Page 59 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation 1. Digital input 1 2. Digital input 2 3. External GND 4. External 24 V 5. Digital output 1 6. Digital output 2 7. External GND 8. External 24 V Fig. 56: Connector side Configuring digital outputs and digital inputs Call up via the setting...
  • Page 60 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Digital output trigger Signals Start depositing arm Signal is sent as soon as the depositing arm starts moving. Start depositing arm, last slice w/o Signal is sent as soon as the depositing arm starts signal moving.

  • Page 61: Further Settings

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Digital inputs functions Pause Motors immediately off Signal stops all motors immediately. Button <Exe- cute> goes off. Once the signal is deactivated, the <Execute> button starts flashing. Press <Execute> to start the reference run.

  • Page 62: Load The Product

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Parameter Validation: If the checkbox is ticked (default), parameter changes must be confirmed by the operator. Clear belt: If the checkbox is ticked, after reaching the last portion (program or product end) the conveyor belt will be completely cleared.
  • Page 63 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Carriage with swivel-mounted product holder, horizontal product fixation - The machine is switched on, all functional parts are in a stop position, carriage is on the side of the operator. Take hold of product holder handle, loosen locking lever by using your index finger and lift up until snapped into place.

  • Page 64: First Cut Function

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Carriage with product holder which cannot be swiveled, vertical product clamping - The machine is switched on, all functional parts are in a stop position, carriage is on the side of the operator.

  • Page 65: Discharge Function

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation The first cut icon flashes in the status bar: – before and during first cut slicing – after resetting the portions counter to zero – to show that the first cut is done after product change and again after restart. Function First cut discharge This function is available for devices with conveyor belt.

  • Page 66: Slice Product

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation With the discharge deactivated, after slicing the first cut the machine with conveyor behaves in the same manner as the machine with depositing table. Notes: "Remove first cut slices from depositing table.
  • Page 67 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation WARNING Rotating blade! Cut injuries – Do not allow yourself to become distracted. Concentrate on the task in hand and avoid time pressure. – During operation, do not reach into the path of the carriage. –...
  • Page 68 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Choose depositing type. (stacks, shin- gles lengthwise, shingles crosswise, cir- cular pattern, shaving) The selection will be shown via a check. Confirm selection. The default values for the selected Deposit- ing type will be loaded.
  • Page 69 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Saving changed parameters. To open PLU menu tap the arrow on the information bar. Use your finger and wipe in arrow direc- tion. A mask to enter PLU number and PLU name opens.

  • Page 70: Plu Direct Key

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation 6.12.1 PLU direct key (not available for all variants) Direct PLU keys on the main page allow fast opening of saved PLUs. Whether a PLU has a direct key can be selected in the PLU menu.
  • Page 71 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation If the slicer is not fitted with a scale, the tile target weight is not available. Tap tile Target weight The window to switch the scale off/on and to change the target weight opens.

  • Page 72: Reference Weight

    (e.g. fork-lift truck activities) near the machine. Installation The machine has to be leveled exactly on the Bizerba stand. To ensure the scale's accuracy, it is absolutely necessary that the machine is aligned horizontally. NOTICE! At an inclination of > 1 degree of the scale as com- pared to the horizontal plane the established weight value is less than the actual weight.

  • Page 73: Ending Slicing

    Instruction manual NSF VSI / VSI W / VSI T / VSI Operation Target weight Optimum as of 150 g. With a target weight smaller than 150 g the target weight devia- tion increases, even instable weight values are possible. Number of slices Optimum as of 4 slices per row.
  • Page 74 Instruction manual NSF VSI / VSI W / VSI T / VSI Operation – at end of product – in case of malfunctions, e.g. jam – in case of voltage deviations outside the tolerance range >10 ms [} 111] – if a safety circuit is interrupted The drives go into stand-by position: –...

  • Page 75: Troubleshooting

    Switch off machine immediately if untypical noises are heard or if there is a suspected risk of injury. Inform your respective Customer Services if you cannot remove the fault yourself. Please provide the Bizerba customer service with the following information: – Machine type (see identification plate), – Machine number (see identification plate), –...

  • Page 76: Maintenance

    Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Maintenance Preparation for cleaning Clean thoroughly: – before putting into operation – depending on use and application frequency – depending on the product – depending on the ambient temperature –...

  • Page 77: Removing Components

    Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Tilt carriage outward into cleaning posi- tion within 10 s. If time was exceeded, press <Execute> again. Switch off machine. Remove the plug and protect against moisture. Fig. 87: Tilt the carriage to the outside Removing components WARNING...
  • Page 78 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Depositing table VSI, VSI W Use both hands to lift table up a little on the operator side and pull it to the front. Fig. 88: Remove depositing table Light sensor Pull the light barrier upwards out of the holder and hang in to the holder of the...
  • Page 79 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Pull conveyor belt on support bar to- wards operator. Discharge conveyor has been decoupled from drive. Fig. 91: Decouple conveyor belt VSI T Use both hands to hold on to the sides of the center of the conveyor and tilt it to- wards you and then lift it up.
  • Page 80 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Remove discharge conveyor from the coupling to the right. Discharge conveyor has been decoupled from drive. Fig. 94: Decouple discharge conveyor VSI TW Remove discharge conveyor exactly to- wards the top.
  • Page 81 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Depositing arm Loosen screw connection and remove hub of depositing arm from bearing to the right. Fig. 97: Depositing arm Chain frame CAUTION! Risk of injury at chain spikes. Using the right hand, swivel feed roller to the left and hold it firmly.
  • Page 82 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Product holder, 400 mm carriage Loosen star knob. Remove product holder in upward direc- tion. Fig. 100: Product holder Feeding carriage, 400 mm carriage CAUTION! Risk of injury at driver spikes. Take hold of product holder handle, loosen locking lever and swivel upwards until snapped into place.
  • Page 83 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Product fixation device, vertical Loosen star knob on guide element. Remove product fixation device. Fig. 103: Product fixation device, vertical Product fixation device, horizontal CAUTION! Do not reach into path of prod- uct fixation device.
  • Page 84 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Blade cover Hold blade cover at handle. Loosen lock behind the blade guard ring and remove blade cover. Fig. 106: Blade cover Deflector CAUTION! Risk of injury on deflector edge.

  • Page 85: Cleaning

    Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Cover interface ports Cover the USB port of the display and operating unit using the captive cap. Cover the Ethernet port of the machine housing using the captive cap. Fig. 108: Cover interface ports Now the machine is ready for cleaning.
  • Page 86 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Blade cleaning Press a wet disposable cleaning cloth against the blade surface and slowly wipe away from the center. Clean the back of the blade in the same manner.
  • Page 87 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Fixed machine parts Clean, rinse and sanitize all surfaces in- cluding deflector as per cleaning plan. Fig. 111: Machine housing Fig. 112: VSI scale Fig. 113: VSI T scale 38065447007 en-US 87 / 118...
  • Page 88 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Wipe gauge plate away from blade. Never wipe towards the blade. Fig. 114: Gauge plate Wipe carriage. Leave surfaces dry in the air. The scale must be dry to avoid a force shunt during operation. 88 / 118 38065447007 en-US...
  • Page 89 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance 38065447007 en-US 89 / 118...

  • Page 90: Cleaning Plan For Slicers

    Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Cleaning plan for slicers Work steps Recom- Procedure Cleaning devices Notes mended clean- ing agents Preparatory according to in- measures struction manual [} 76] Disassemble according to in- all removable struction manual parts...
  • Page 91 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Work steps Recom- Procedure Cleaning devices Notes mended clean- ing agents Checking Visually check for optical clean- liness Drying rub dry or leave Disposable cloth Leave removed to dry parts apart from one another to allow...

  • Page 92: Preparing The Machine For Operation

    Depending on the product, there could still be a risk from viruses and bac- teria which cannot be completely eliminated despite regular cleaning. The following cleaning agents can be acquired from the Bizerba customer service: Designation Order no. Packaging unit...
  • Page 93 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Blade cover Hold blade cover at handle, tilt towards blade and fix into position with the stud. Fasten lock behind blade guard ring. NOTICE! Do not mix up with covers of other machines.
  • Page 94 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Product holder, 400 mm carriage CAUTION! Risk of jamming between product holder and gauge plate. Hold on to the handle on the product holder, loosen the clamping device using the lock lever and move it downwards.
  • Page 95 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Product fixation device, horizontal Push fixation plate in guidance from top and fasten clamp handle. Fig. 122: Product fixation device, horizontal Guide cam Insert guide cam between the transport chains and fasten it using the clamp han- dle.
  • Page 96 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Depositing arm Push depositing arm onto carriage shaft and turn until the hub catches the groove. Tighten. Fig. 125: Depositing arm Depositing table VSI, VSI W Insert slightly tilted depositing table backwards in guidance and push it downwards.
  • Page 97 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Push the conveyor as far as it will go to- wards the coupling, if necessary turn the drive shaft until it connects with the cou- pling bolts. Fig. 128: Couple conveyor belt VSI T Secure the conveyor belt by setting the lock at the belt support.
  • Page 98 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Discharge conveyor VSI TW CAUTION! Risk of crushing fingers be- tween belt support and conveyor. Engage discharge conveyor into the belt mount from the top. Fig. 131: Engage conveyor Push conveyor to the left into the jaw clutch coupling.
  • Page 99 – Check if the machine is complete before it is re-started. – Check if components are positioned correctly and firmly. – Only use original Bizerba spare parts and accessories. 38065447007 en-US 99 / 118...

  • Page 100: Service And Maintenance

    Bizerba Service. WARNING Changing the blade! Severe injuries and damage to property. – For safety reasons, the blade may only be changed by Bizerba cus- tomer service. – This also applies when using the separately available blade removal tool.
  • Page 101 Before sharpening, clean with brush and solving detergent. If sharpening stones are worn, replace stones. Replacement parts are supplied by Bizerba customer services. When replacing, do not confuse sharpening and honing stones. Preparation for sharpening...

  • Page 102: Sharpening

    Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Attaching the sharpener WARNING! Risk of injury on open blade. - Blade is not running and gauge plate is open. - Sharpener marking must be at "0". Move carriage to relevant position. Mount sharpener to gauge plate from the top.

  • Page 103: Honing

    Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Check the grinding device Using a pen or pencil, touch the right edge of the blade while moving the pen from inside to outside. Burr must be noticeable, otherwise the sharpening procedure must be re- peated.

  • Page 104: Checking Seals And Sealings

    Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance 8.6.4 Checking seals and sealings Fig. 141: Installation points for seals and sealings 104 / 118 38065447007 en-US...
  • Page 105 Instruction manual NSF VSI / VSI W / VSI T / VSI Maintenance Installation points for seals and sealings between the following parts: Gauge plate - machine housing Carriage plate - handle Conveyor belt - machine housing Chain frame - machine housing Depositing arm - machine housing Spindle - carriage 2x Product holder guide shaft - Product holder guidance 2x...

  • Page 106: Technical Data

    Instruction manual NSF VSI / VSI W / VSI T / VSI Technical data Technical data Dimensions VSI / VSI W Fig. 142: Dimensions of VSI with carriage 400 mm Installation surface Length x width INstallation on table 606 x 628 mm / 23.9" x 24.7" Installation on a stand 800 x 847 mm / 31.5"...

  • Page 107: Dimensions Vsi T

    Instruction manual NSF VSI / VSI W / VSI T / VSI Technical data Packaging Length x width x height 400 mm carriage, display at the top, without 680 x 1080 x 995 mm / 26.8" x 42.5" x 39.2" stand 600 mm carriage, display at the top, without 680 x 1375 x 995 mm / 26.8"...

  • Page 108: Dimensions Vsi Tw

    Instruction manual NSF VSI / VSI W / VSI T / VSI Technical data 1 portion belt, wire mesh 325 x 250 mm / 12.8" x 9.8" 1 portion belt, plastic belts 30 mm 325 x 250 mm / 12.8" x 9.8" Blade diameter 330 mm / 13.0"...
  • Page 109 Instruction manual NSF VSI / VSI W / VSI T / VSI Technical data VSI TW on a stand, 400 mm carriage, dis- 1790 x 1188 x 1332 mm / 70.5" x 46.8" x play at the bottom 52.4" Conveyor belt Length x width 5 portions belt, wire mesh 950 x 250 mm / 37.4"...

  • Page 110: Technical Data

    Instruction manual NSF VSI / VSI W / VSI T / VSI Technical data Technical data VSI / VSI W VSI T VSI TW Product size Height: 50 - 180 mm / 2.0" -7.1" Width: 50 - 240 mm / 2.0" - 9.4" Round: Ø...

  • Page 111: Power Supply

    Instruction manual NSF VSI / VSI W / VSI T / VSI Technical data Power supply Technical data of power supply – Mains supply Single-phase alternating current, see rating plate – Permissible mains voltage tolerance (static) normal At 100 to 400 V: +6% to - 10% of nominal value In case of deviations of >10 ms the machine turns off.

  • Page 112: Attachment

    Instruction manual NSF VSI / VSI W / VSI T / VSI Attachment Attachment 10.1 Parameter defaults and input ranges Parameter sym- Parameter name Default value Minimum Maximum Depositing type Stacking Depositing offset 0 mm 0 mm 190 mm crosswise Depositing offset 0 mm 0 mm...
  • Page 113 Instruction manual NSF VSI / VSI W / VSI T / VSI Attachment Parameter sym- Parameter name Default value Minimum Maximum Shingling length, 240 mm 50 mm 286 mm shingling length- wise Shingling length, 240 mm 50 mm 240 mm shingling cross- wise Number of por-...
  • Page 114 Instruction manual NSF VSI / VSI W / VSI T / VSI Attachment Parameter sym- Parameter name Default value Minimum Maximum Number of rows crosswise Row spacing 10 mm 0 mm 100 mm lengthwise, stacks Row spacing 10 mm -100 mm 100 mm lengthwise, shin- gles crosswise...

  • Page 115: Set Programs

    Instruction manual NSF VSI / VSI W / VSI T / VSI Attachment Parameter sym- Parameter name Default value Minimum Maximum Product feed off- 0.1 mm -0.5 mm 0.5 mm Gauge plate off- 0.0 mm -0.5 mm 0.5 mm 10.2 Set programs Each machine has standard PLUs saved.
  • Page 116 Instruction manual NSF VSI / VSI W / VSI T / VSI Attachment VSI T depositing on conveyor num- 9999 50 9999 50 9999 50 9999 50 9999 50 infi- 9999 50 infi- nite nite 9999 50 9999 50 9999 50 9999 45 The reference weight for all standard PLUs is 10.0 g/mm.

  • Page 117: Checklist Installation And Start-Up

    (max. distance of 1 m) of the machine allowing the machine to be connected with the provided power cable. The power plug must always be accessible to the Bizerba service technician at any time since it functions as a supply circuit disconnect in case of a repair.
  • Page 118 Instruction manual NSF VSI / VSI W / VSI T / VSI Attachment Done The horizontal setup of the machine was checked by means of a spirit level or during setup on the stand with the bubble. Scale recalibrated and functioning tested. Electrical safety meets relevant country-specific regulations.

This manual is also suitable for:

Vsi330 f wVsi330 f tVsi330 f tw

Table of Contents