Net Media MM73 User Manual page 85

Net media mm73 modulator: user guide
Table of Contents

Advertisement

SCM1 SCM2 SCM3
B/W
Color
This self contained camera and modulator converts its video signal to a selected television channel. It is powered over the
same coax cable that returns the video broadcast signal for One Wire Video™ installation. It mounts to a typical round 4
inch junction box and is viewed with a television tuner. Other junction boxes from your local hardware store may also be
used after replacing the round base with another that has a 1/2 inch diameter hole for the elbow bracket. Equipment that
does not have a tuner, such as a security monitor, Quad display, or DVR, will require a demodulator (any TV tuner device with
a composite video output such as a VCR) to convert the video for its use.
Product Includes:
1. Camera Assembly (Camera, Modulator, Housing, Housing Cap, Elbow Bracket,
Locking Ring, Base, Gasket, Video/Power Connector).
2. Power Injector and 12V DC 300mA Power Transformer, Center Conductor Positive.
3. Mounting hardware (Mounting Screws, Grounding Strap, and Screw).
Housing
Available in Ivory only:
Model
Camera Type
SCM1
B&W
SCM2
Color
SCM3
Day/Night Color
Modulator
Not Shown - Behind Camera Bracket.
Switch bank sets output channel:
UHF 14-69 or CABLE 70-94, 100-125.
Elbow Bracket
Adjusts camera angle at base,
screw, and housing. Installs in
1/2" junction box covers.
Power Injector
Connects power transformer to coax
for One Wire Video™ installation.
Video/Power Connector
Power and video share one coax
through female F connector.
FEATURES
Modulator built into camera
One Wire Video™ installation
Combines with existing TV channels
Viewable on multiple televisions
Excellent image quality
Tough aluminum housing
Weather resistant enclosure
Internally routed cables
Mounts to standard electrical fixtures
Mounts directly to walls and ceilings
Works in low light conditions
Adjustable camera angles
Tamper resistant wiring
Includes power supply and power injector
1 year limited warranty
NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com
Indoor/Outdoor Weather Resistant
Day/Night
Color
SPECIFICATIONS
Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Modulation Method:
Output Channel:
Output Level:
Output Connector:
Cable Type:
Power Requirement:
Power Connector:
Housing Size:
Base Size:
Mounting Holes:
Weight:
Modulated Camera
Camera Bracket, and Modulator.
Base, Gasket & Screws
Mount to round 4" junction box.
B/W
3.6mm
1/3" CCD
350 lines
72˚ Horizontal
54˚ Horizontal
0.7 Lux F2.0
0.5 Lux F1.2
Yes
Digital Crystal PLL
UHF 14-69, CABLE 70-94, 100-125
+30dBmV
Female F, 75 Ohm
RG59, RG6 or better
12V DC, 300mA
5.5mm OD, 2.1mm ID, center positive
2.13" dia. x 3" long
4.5" dia., .75" high, 1/2" hole
3.5" centers
Camera Lens
Comes prefocused from
factory but can be adjusted
by rotating in either direction.
Camera Bracket
Slot indicates image bottom.
Use slot to pull bracket out
and remove Modulator.
Housing Cap
Remove to access Camera Lens,
Locking Ring
Secures elbow bracket to
base at desired position.
Color
Day/Night Color
3.7mm
3.6mm
1/4" CCD
1/3" CCD
470 lines
470 lines
72˚ Horizontal
0.3 Lux F1.2
No
Yes
1 lb.
(subject to change without notice)
MAN-MODLAMP
REV0612A

Advertisement

Table of Contents
loading

Table of Contents