Net Media MM73 User Manual

Net media mm73 modulator: user guide

Table of Contents

Quick Links

Download this manual

MM73

The MM73 TriplePlay Modulator converts three composite video and stereo audio signals to three

monaural television channels. The selectable channels are viewed with a standard television (SDTV)

tuner. Once modulated, the signals are no longer bound to a single monitor or TV; they can be com-

bined with antenna, cable, or satellite signals for distribution to multiple TV's throughout the location.

This provides convenient viewing access to security cameras, DVR's, or other audio/video (A/V) sources

such as DVD's and VCR's.

Product Includes:

1. Modulator Assembly (3 Video Input Connector, 3 Audio Input Connector, RF Output Connector,

Power Input Connector, End Plate, 3 Switch Banks, Power LED).

2. 12V DC 300mA Power Transformer, Center Conductor Positive.

3. 3 RCA Video Cables, 3 3.5mm Stereo to Dual RCA Audio Cables.

Video Input Connectors

RCA composite inputs for video sources

such as cameras, quads, DVR's, DVD's, etc.

Audio Input Connectors

Combine stereo input for

monaural output.

End Plate

Remove to access

Switch Banks.

FEATURES

Digital PLL locked audio & video - no drift

Combines with existing TV channels

Viewable on multiple televisions

UHF & Cable channel coverage

Channel retained during power outage

Tough aluminum housing

Includes power supply

5 year limited warranty

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com

TriplePlay Modulator

Baseband A/V to SDTV Converter

SPECIFICATIONS

Modulation Method:

Output Channel:

Output Level:

Output Connector:

Video Input Connectors:

Audio Input Connectors:

Audio Output:

Cable Type:

Power Requirement:

Power Connector:

Housing Size:

Weight:

RF Output Connector

Connects modulated output

channels to video distribution

system and televisions.

Power Input Connector

12V DC 300mA, center positive.

Switch Banks

Behind End Plate -

Set output channels:

CABLE 70-94, 100-125.

Indicates that unit is on.

Digital Crystal PLL

SDTV: UHF 14-69, CABLE 70-94, 100-125

+30dBmV

Female F, 75 Ohm

3- RCA Phono, 75 Ohm, 1 Vp-p

3- 3.5mm Stereo, 75,000 Ohm, 1 Vp-p

Monaural

RG59, RG6 or better

12V DC, 300mA

5.5mm OD, 2.1mm ID, center positive

3.9" long x 5.5" wide x 0.9" high

9.0 oz.

(subject to change without notice)

UHF 14-69

Power LED

MAN-MM73

REV0703A

Table of Contents

Summary of Contents for Net Media MM73

Page 1 TriplePlay Modulator Baseband A/V to SDTV Converter The MM73 TriplePlay Modulator converts three composite video and stereo audio signals to three monaural television channels. The selectable channels are viewed with a standard television (SDTV) tuner. Once modulated, the signals are no longer bound to a single monitor or TV; they can be com- bined with antenna, cable, or satellite signals for distribution to multiple TV’s throughout the location.
Page 2: Installation Procedures
MM73 Installation Procedures: 1. Remove the End Plate from the modulator assembly and set each channel with the switches as shown in Figure 1. Choose unused channels that match the tuning mode of the televisions. With antenna tuning, choose UHF channels from 14-69.With cable tuning, choose CABLE channels from 70-94 or 100- 125.
Page 3: Fcc Information (U.s.a.)
Type of Equipment: Modulator Model: MM73 to which this declaration relates are in conformity with the Title 47 of the US Code of Federal Regulations, Part 15 covering Class B digital devices.
Page 4: Frequently Asked Questions
Figure 4 - Bypassing a digital or analog cable box and recombining to a single coax input on the TV. The kit’s filter removes any conflict on channel 3 or 4. Switch TV from the cable box to the modulator channels. NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com MAN-MM73 REV0703A...
Page 5: Product Includes
MM70 Single Channel Modulator Baseband A/V to SDTV Converter The MM70 Micro-Modulator converts composite video and stereo audio to a monaural television signal. The selectable channel is viewed with a standard television (SDTV) tuner. Once modulated, the signal is no longer bound to a single monitor or TV; it can be combined with antenna, cable, or satellite signals for distribution to multiple TV’s throughout the location.
Page 6 MM70 Installation Procedures: 1. Remove the End Plate from the modulator assembly and set the channel with the switches as shown in Figure 1. Choose an unused channel that matches the tuning mode of the televisions. With antenna tuning, choose a UHF channel from 14-69. With cable tuning, choose a CABLE channel from 70-94 or 100-125.
Page 7 Single Channel Modulator Baseband A/V to SDTV Converter FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 8 Frequently Asked Questions Q- How do I find out if the modulator is working when I can’t see it on any televisions? A- Start with a basic setup: connect modulator to coax and coax to a standard TV with no amplifiers, splitters, filters, cable boxes or other devices involved.
Page 9 TriplePlay Stereo Modulator Baseband A/V to SDTV Converter The MM73 TriplePlay Stereo Modulator converts three composite video and stereo audio signals to three MTS Stereo television channels. The selectable channels are viewed with a standard television (SDTV) tuner. Once modulated, the signals are no longer bound to a single monitor or TV; they can be combined with antenna, cable, or satellite signals for distribution to multiple TV’s throughout the loca-...
Page 10 MM73S Installation Procedures: 1. Remove the End Plate from the modulator assembly and set each channel with the switches as shown in Figure 1. Choose unused channels that match the tuning mode of the televisions. With antenna tuning, choose UHF channels from 14-69.With cable tuning, choose CABLE channels from 70-94 or 100- 125.
Page 11 TriplePlay Stereo Modulator Baseband A/V to SDTV Converter FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 12 Frequently Asked Questions Q- How do I find out if the modulator is working when I can’t see it on any televisions? A- Start with a basic setup: connect modulator to coax and coax to a standard TV with no amplifiers, splitters, filters, cable boxes or other devices involved.
Page 13 MM70S Single Channel Stereo Modulator Baseband A/V to SDTV Converter The MM70S Stereo Modulator converts composite video and stereo audio to an MTS Stereo television signal. The selectable channel is viewed with a standard television (SDTV) tuner. Once modulated, the signal is no longer bound to a single monitor or TV;...
Page 14 MM70S Installation Procedures: 1. Remove the End Plate from the modulator assembly and set the channel with the switches as shown in Figure 1. Choose an unused channel that matches the tuning mode of the televisions. With antenna tuning, choose a UHF channel from 14-69. With cable tuning, choose a CABLE channel from 70-94 or 100-125.
Page 15 Single Channel Stereo Modulator Baseband A/V to SDTV Converter FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 16 Frequently Asked Questions Q- How do I find out if the modulator is working when I can’t see it on any televisions? A- Start with a basic setup: connect modulator to coax and coax to a standard TV with no amplifiers, splitters, filters, cable boxes or other devices involved.
Page 17 RM70 Coax-Powered Modulator Baseband A/V to SDTV Converter The RM70 Coax-Powered Single Channel Modulator converts composite video and stereo audio to a monaural television signal. It is powered over the same coax cable that returns the video broadcast signal. It can even supply remote power to 12VDC cameras for One Wire Video™...
Page 18 RM70 Installation Procedures: 1. Remove the End Plate from the modulator assembly and set the channel with the switches as shown in Figure 1. Choose an unused channel that matches the tuning mode of the televisions. With antenna tuning, choose a UHF channel from 14-69.
Page 19 Coax-Powered Modulator Baseband A/V to SDTV Converter FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 20 Frequently Asked Questions Q- How do I find out if the modulator is working when I can’t see it on any televisions? A- Start with a basic setup: connect modulator to coax and coax to a standard TV with no amplifiers, splitters, filters, cable boxes or other devices involved.
Page 21 RM70-W In-Wall Coax-Powered Modulator Baseband A/V to SDTV Converter The RM70-W in-Wall Coax-Powered Single Channel Modulator converts composite video and stereo audio to a monaural television signal. It mounts in a typical single gang junction box. It is powered over the same coax cable that returns the video broadcast signal.
Page 22 RM70-W Installation Procedures: 1. Remove the End Plate from the modulator assembly and set the channel with the switches as shown in Figure 1. Choose an unused channel that matches the tuning mode of the televisions. With antenna tuning, choose a UHF channel from 14-69.
Page 23 In-Wall Coax-Powered Modulator Baseband A/V to SDTV Converter FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 24 Frequently Asked Questions Q- How do I find out if the modulator is working when I can’t see it on any televisions? A- Start with a basic setup: connect modulator to coax and coax to a standard TV with no amplifiers, splitters, filters, cable boxes or other devices involved.
Page 25: Color Day/Night
NM-UTPEYE UTP Security Camera Indoor Low Profile Eyeball Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia UTP Video Encoder and external UTP Video Decoder to exchange power and video across Unshielded Twisted Pair (UTP) cable, such as CAT5.There is no need to run multiple cables to the camera location! It mounts in round 4 inch electrical fixtures or 2.7 inch diameter holes and is viewed with a security moni- tor or television.
Page 26 NM-UTPEYE DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair needs a dedicated point-to-point wiring circuit.
Page 27: One Year Limited Warranty
UTP Security Camera Indoor Low Profile Eyeball UTP Wiring Information: The UTP cable should be wired for a straight-through connection according to the T-568A specification as shown in Figure 4. FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements.
Page 28 Frequently Asked Questions Q- Can I connect the camera to a computer network or another UTP video system? A- NO! Do not connect the Camera/Decoder UTP cable to a computer network, or another UTP video system! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on pins 7 and 8 of its UTP connector that the other equipment may not be prepared to handle.
Page 29 NM-UTPCAM UTP Security Camera Indoor/Outdoor Weather Resistant Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia UTP Video Encoder and external UTP Video Decoder to exchange power and video across Unshielded Twisted Pair (UTP) cable, such as CAT5. There is no need to run multiple cables to the camera location! It mounts to a typical round 4 inch junction box and is viewed with a security monitor or television.
Page 30 NM-UTPCAM DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair needs a dedicated point-to-point wiring circuit.
Page 31 UTP Security Camera Indoor/Outdoor Weather Resistant UTP Wiring Information: The UTP cable should be wired for a straight-through connection according to the T-568A specification as shown in Figure 4. FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements.
Page 32 Frequently Asked Questions Q- Can I connect the camera to a computer network or another UTP video system? A- NO! Do not connect the Camera/Decoder UTP cable to a computer network, or another UTP video system! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on pins 7 and 8 of its UTP connector that the other equipment may not be prepared to handle.
Page 33 NM-UTPJBOX UTP Security Camera In-Wall Junction Box Mounted Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia UTP Video Encoder and external UTP Video Decoder to exchange power and video across a single Unshielded Twisted Pair (UTP) cable,such as CAT5.There is no need to run multiple cables to the camera location! It mounts in a typical single gang junction (light switch) box and is viewed with a security monitor or television.
Page 34 NM-UTPJBOX DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair needs a dedicated point-to-point wiring circuit.
Page 35 UTP Security Camera In-Wall Junction Box Mounted UTP Wiring Information: The UTP cable should be wired for a straight-through connection according to the T-568A specification as shown in Figure 4. FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements.
Page 36 Frequently Asked Questions Q- Can I connect the camera to a computer network or another UTP video system? A- NO! Do not connect the Camera/Decoder UTP cable to a computer network, or another UTP video system! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on pins 7 and 8 of its UTP connector that the other equipment may not be prepared to handle.
Page 37 NM-UTPLAMP UTP Security Camera Indoor/Outdoor Weather Resistant Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia UTP Video Encoder and external UTP Video Decoder to exchange power and video across a single Unshielded Twisted Pair (UTP) cable, such as CAT5. There is no need to run multiple cables to the camera location! It mounts to a typical round 4 inch junction box and is viewed with a security moni- tor or television.
Page 38 NM-UTPLAMP DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair needs a dedicated point-to-point wiring circuit.
Page 39 UTP Security Camera Indoor Low Profile Eyeball UTP Wiring Information: The UTP cable should be wired for a straight-through connection according to the T-568A specification as shown in Figure 4. FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements.
Page 40 Frequently Asked Questions Q- Can I connect the camera to a computer network or another UTP video system? A- NO! Do not connect the Camera/Decoder UTP cable to a computer network, or another UTP video system! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on pins 7 and 8 of its UTP connector that the other equipment may not be prepared to handle.
Page 41 NM-UTPDOME UTP Security Camera Indoor Dome Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia UTP Video Encoder and external UTP Video Decoder to exchange power and video across Unshielded Twisted Pair (UTP) cable, such as CAT5.There is no need to run multiple cables to the camera location! It mounts to walls or ceilings and is viewed with a security monitor or television.
Page 42 NM-UTPDOME DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair needs a dedicated point-to-point wiring circuit.
Page 43 UTP Security Camera Indoor Dome UTP Wiring Information: The UTP cable should be wired for a straight-through connection according to the T-568A specification as shown in Figure 4. FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements.
Page 44 Frequently Asked Questions Q- Can I connect the camera to a computer network or another UTP video system? A- NO! Do not connect the Camera/Decoder UTP cable to a computer network, or another UTP video system! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on pins 7 and 8 of its UTP connector that the other equipment may not be prepared to handle.
Page 45 NM-UTPBALL UTP Security Camera Indoor Ball Camera Day/Night Color Color This general purpose surveillance camera utilizes a built-on NetMedia UTP Video Encoder and external UTP Video Decoder to exchange power and video across Unshielded Twisted Pair (UTP) cable, such as CAT5. There is no need to run multiple cables to the camera location! It mounts to a typical rectangular junction box and is viewed with a security monitor or television.
Page 46 NM-UTPBALL DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair needs a dedicated point-to-point wiring circuit.
Page 47 UTP Security Camera Indoor Ball Camera UTP Wiring Information: The UTP cable should be wired for a straight-through connec- tion according to the T-568A specification as shown in Figure 4. FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements.
Page 48 Frequently Asked Questions Q- Can I connect the camera to a computer network or another UTP video system? A- NO! Do not connect the Camera/Decoder UTP cable to a computer network, or another UTP video system! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on pins 7 and 8 of its UTP connector that the other equipment may not be prepared to handle.
Page 49 NM-POCEYE Power over Coax Camera Indoor Low Profile Eyeball Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia Power over Coax (PoC) Video Encoder and external PoC Video Decoder to exchange power and video across a single coax cable, such as RG6.There is no need to run multiple cables to the camera location! It mounts in round 4 inch electrical fixtures or 2.7 inch diameter holes and is viewed with a security moni- tor or television.
Page 50 NM-POCEYE DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a coax cable (RG6 recommended) to the F-Connectors of the camera and Video Decoder. Each Camera/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Camera/Decoder coax to video distribution equipment! Doing so could damage this product and/or the other attached devices! 2.
Page 51 Power over Coax Camera Indoor Low Profile Eyeball FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 52 Frequently Asked Questions Q- Can I connect the camera coax to video distribution equipment? A- NO! Do not connect the F-Connector coax of the camera or Decoder to other video equipment! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on the coax that other equipment may not be prepared to handle.
Page 53 NM-POCCAM Power over Coax Camera Indoor/Outdoor Weather Resistant Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia Power over Coax (PoC) Video Encoder and external PoC Video Decoder to exchange power and video across a single coax cable, such as RG6. There is no need to run multiple cables to the camera location! It mounts to a typical round 4 inch junction box and is viewed with a security monitor or television.
Page 54 NM-POCCAM DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a coax cable (RG6 recommended) to the F-connectors of the camera and Video Decoder. Each Camera/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Camera/Decoder coax to video distribution equipment! Doing so could damage this product and/or the other attached devices! 2.
Page 55 Power over Coax Camera Indoor/Outdoor Weather Resistant FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 56 Frequently Asked Questions Q- Can I connect the camera coax to video distribution equipment? A- NO! Do not connect the F-Connector coax of the camera or Decoder to other video equipment! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on the coax that other equipment may not be prepared to handle.
Page 57 NM-POCJBOX Power over Coax Camera In-Wall Junction Box Mounted Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia Power over Coax (PoC) Video Encoder and external PoC Video Decoder to exchange power and video across a single coax cable, such as RG6. There is no need to run multiple cables to the camera location! It mounts in a typical single gang junction (light switch) box and is viewed with a security monitor or television.
Page 58 NM-POCJBOX DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a coax cable (RG6 recommended) to the F-connectors of the camera and Video Decoder. Each Camera/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Camera/Decoder coax to video distribution equipment! Doing so could damage this product and/or the other attached devices! 2.
Page 59 Power over Coax Camera In-Wall Junction Box Mounted FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 60 Frequently Asked Questions Q- Can I connect the camera coax to video distribution equipment? A- NO! Do not connect the F-Connector coax of the camera or Decoder to other video equipment! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on the coax that other equipment may not be prepared to handle.
Page 61 NM-POCLAMP Power over Coax Camera Indoor/Outdoor Weather Resistant Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia Power over Coax (PoC) Video Encoder and external PoC Video Decoder to exchange power and video across a single coax cable, such as RG6. There is no need to run multiple cables to the camera location! It mounts to a typical round 4 inch junction box and is viewed with a security monitor or television.
Page 62 NM-POCLAMP DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a coax cable (RG6 recommended) to the F-connectors of the camera and Video Decoder. Each Camera/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Camera/Decoder coax to video distribution equipment! Doing so could damage this product and/or the other attached devices! 2.
Page 63 Power over Coax Camera Indoor/Outdoor Weather Resistant FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 64 Frequently Asked Questions Q- Can I connect the camera coax to video distribution equipment? A- NO! Do not connect the F-Connector coax of the camera or Decoder to other video equipment! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on the coax that other equipment may not be prepared to handle.
Page 65 NM-POCDOME Power over Coax Camera Indoor Dome Day/Night Color Color This general purpose surveillance camera utilizes a built-in NetMedia Power over Coax (PoC) Video Encoder and external PoC Video Decoder to exchange power and video across a single coax cable, such as RG6.There is no need to run multiple cables to the camera location! It mounts to walls or ceilings and is viewed with a security monitor or television.
Page 66 NM-POCDOME DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a coax cable (RG6 recommended) to the F-Connectors of the camera and Video Decoder. Each Camera/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Camera/Decoder coax to video distribution equipment! Doing so could damage this product and/or the other attached devices! 2.
Page 67 Power over Coax Camera Indoor Dome FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 68 Frequently Asked Questions Q- Can I connect the camera coax to video distribution equipment? A- NO! Do not connect the F-Connector coax of the camera or Decoder to other video equipment! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on the coax that other equipment may not be prepared to handle.
Page 69 NM-POCBALL Power over Coax Camera Indoor Ball Camera Day/Night Color Color This general purpose surveillance camera utilizes a built-on NetMedia Power over Coax (PoC) Video Encoder and external PoC Video Decoder to exchange power and video across a single coax cable, such as RG6. There is no need to run multiple cables to the camera location! It mounts to a typical rectangular junction box and is viewed with a security monitor or television.
Page 70 NM-POCBALL DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a coax cable (RG6 recommended) to the F-connectors of the camera and Video Decoder. Each Camera/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Camera/Decoder coax to video distribution equipment! Doing so could damage this product and/or the other attached devices! 2.
Page 71 Power over Coax Camera Indoor Ball Camera FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 72 Frequently Asked Questions Q- Can I connect the camera coax to video distribution equipment? A- NO! Do not connect the F-Connector coax of the camera or Decoder to other video equipment! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on the coax that other equipment may not be prepared to handle.
Page 73 NM-MODEYE Modulated Camera Indoor Low Profile Eyeball Day/Night Color Color The MODCAM is a self contained camera and modulator that converts the video signal to a selected television channel. It is powered over the same coax cable that returns the video broadcast signal for One Wire Video™ installation. It mounts in a round 2.7 inch diameter hole and is viewed with a television tuner.
Page 74 NM-MODEYE DO NOT CUT OR SPLICE THE CAMERA’S CABLE. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Unscrew the Exterior Ring and remove the Camera Eyeball from the camera assembly. Locate the Modulator switch bank and set the channel as shown in Figure 1. Choose an unused channel that matches the tuning mode of the televisions.
Page 75 Modulated Camera Indoor Low Profile Eyeball FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authori- zation to use the product in the USA.
Page 76 Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 77 NM-MODCAM Modulated Camera Indoor/Outdoor Weather Resistant Day/Night Color Color The MODCAM is a self contained camera and modulator that converts the video signal to a selected television channel. It is powered over the same coax cable that returns the video broadcast signal for One Wire Video™ installation. It mounts to a typical round 4 inch junction box and is viewed with a television tuner.
Page 78 NM-MODCAM DO NOT CUT OR SPLICE THE CAMERA’S CABLE. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Remove the Housing Cap from the camera assembly and set the channel with the switches as shown in Figure 1. Choose an unused channel that matches the tuning mode of the televisions.
Page 79 Modulated Camera Indoor/Outdoor Weather Resistant FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 80 NM-MODCAM Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 81 Modulated Camera SC01 SC02 SC03 In-Wall Junction Box Mounted Day/Night Color Color This self contained camera and modulator converts its video signal to a selected television channel. It is powered over the same coax cable that returns the video broadcast signal for One Wire Video™ installation. It mounts in a typical single gang junction (light switch) box and is viewed with a television tuner.
Page 82 SC01 SC02 SC03 DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. DAMAGE FROM EXPOSURE TO MOISTURE, STATIC DISCHARGE, OR OTHER HARMFUL ENVIRONMENTAL FACTORS IS NOT COVERED BY THE WARRANTY. Installation Procedures: 1.
Page 83 Modulated Camera In-Wall Junction Box Mounted FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 84 Frequently Asked Questions Q- When using the Dark Lens Cover, why does the picture look too bright, dark, or strange? A- The dark lens covers make the camera less obtrusive but they may not work well under some conditions. The cover that ships with the color camera is similar to tinted sunglasses;...
Page 85 Modulated Camera SCM1 SCM2 SCM3 Indoor/Outdoor Weather Resistant Day/Night Color Color This self contained camera and modulator converts its video signal to a selected television channel. It is powered over the same coax cable that returns the video broadcast signal for One Wire Video™ installation. It mounts to a typical round 4 inch junction box and is viewed with a television tuner.
Page 86 SCM1 SCM2 SCM3 DO NOT CUT OR SPLICE THE CAMERA’S CABLE. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Remove the Housing Cap from the camera assembly and pull the Camera Bracket out to set the channel with the switches as shown in Figure 1.
Page 87 Modulated Camera Indoor/Outdoor Weather Resistant FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 88 Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 89 NM-VIDEYE Security Video Camera Indoor Low Profile Eyeball Day/Night Color Color This general purpose security camera mounts in a round 2.7 inch diameter hole and is viewed with a security monitor. To view the camera on a single standard television, use the TV’s composite RCA Video Input jack. Product Includes: 1.
Page 90 NM-VIDEYE DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Ensure that the camera is grounded with the ground strap as shown in the FCC Information. 2. Connect a grounded video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the camera’s Video Connector.
Page 91 Security Video Camera Indoor/Outdoor Weather Resistant FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 92 Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 93 NM-VIDCAM Security Video Camera Indoor/Outdoor Weather Resistant Day/Night Color Color This general purpose security camera mounts to a typical round 4 inch junction box and is viewed with a security monitor. Other junction boxes from your local hardware store may also be used after replacing the round base with another that has a 1/2 inch diameter hole for the elbow bracket.
Page 94 NM-VIDCAM DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Ensure that the camera is grounded with the ground strap as shown in the FCC Information. 2. Connect a grounded video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the camera’s Video Connector.
Page 95 Security Video Camera Indoor/Outdoor Weather Resistant FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 96 Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 97 Security Video Camera SC50 SC51 SC53 In-Wall Junction Box Mounted Day/Night Color Color This general purpose security camera mounts in a typical single gang junction (light switch) box and is viewed with a security monitor. To view the camera on a single standard television, use the TV’s composite RCA Video Input jack. Product Includes: 1.
Page 98 SC50 SC51 SC53 DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. DAMAGE FROM EXPOSURE TO MOISTURE, STATIC DISCHARGE, OR OTHER HARMFUL ENVIRONMENTAL FACTORS IS NOT COVERED BY THE WARRANTY. Installation Procedures: 1.
Page 99 Security Video Camera In-Wall Junction Box Mounted FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 100 Frequently Asked Questions Q- When using the Dark Lens Cover, why does the picture look too bright, dark, or strange? A- The dark lens covers make the camera less obtrusive but they may not work well under some conditions. The cover that ships with the color camera is similar to tinted sunglasses;...
Page 101 Security Video Camera SCE1 SCE2 SCE3 Indoor/Outdoor Weather Resistant Day/Night Color Color This general purpose security camera mounts to a typical round 4 inch junction box and is viewed with a security monitor. Other junction boxes from your local hardware store may also be used after replacing the round base with another that has a 1/2 inch diameter hole for the elbow bracket.
Page 102 SCE1 SCE2 SCE3 DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Ensure that the camera is grounded with the ground strap as shown in the FCC Information. 2.
Page 103 Security Video Camera Indoor/Outdoor Weather Resistant FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 104 Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 105 Security Video Camera SCE3-IR Indoor/Outdoor Weather Resistant Day/Night Color with IR LED’s This day/night color security camera with built-in infrared (IR) LED’s mounts to a typical round 4 inch junction box and is viewed with a security monitor. IR illumination provides invisible light for the camera in complete darkness. Other base plates with a 1/2 inch diameter hole for the elbow bracket may be used instead.
Page 106 SCE3-IR DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Ensure that the camera is grounded with the ground strap as shown in the FCC Information. 2. Connect a grounded video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the camera’s Video Connector.
Page 107 Security Video Camera Indoor/Outdoor Weather Resistant FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority,granted by the FCC,to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 108 Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 109 NM-VIDDOME Security Video Camera Indoor Dome Day/Night Color Color This general purpose security camera mounts to walls or ceilings and is viewed with a security monitor. To view the camera on a single standard television, use the TV’s composite RCA Video Input jack. Product Includes: 1.
Page 110 NM-VIDDOME DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a grounded video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the camera’s Video Connector. Adapters, such as BNC to F or RCA, may be used as necessary. 2.
Page 111 Security Video Camera Indoor Dome FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 112 Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 113 NM-VIDBALL Security Video Camera Indoor Ball Camera Day/Night Color Color This general purpose security camera mounts to a typical rectangular junction box and is viewed with a security monitor. To view the camera on a single standard television, use the TV’s composite RCA Video Input jack.
Page 114 NM-VIDBALL DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect a video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the camera’s Video Connector. Adapters, such as BNC to F or RCA, may be used where appropriate. 2.
Page 115 Security Video Camera Indoor Ball Camera FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 116 Frequently Asked Questions Q- Why do the light areas of the picture look washed out? A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has both light and shadow, the camera adjusts the iris based on the percentage of each area in the image.
Page 117: Infrared Illuminator
SCIR Infrared Illuminator Powerful Indoor/Outdoor IR Spotlight The NetMedia SCIR Infrared (IR) Illuminator provides night vision for IR (850nm) sensitive cameras. It enables cameras such as NetMedia’s B/W and Day/Night color models to see in complete darkness. It mounts to a typical round 4 inch junction box.
Page 118 One Year Limited Warranty NetMedia, Inc. warrants this product to be free from defects in materials and workmanship under normal use and service for One Year from the date of purchase or NetMedia will repair or, at its option, replace the defective product. Please keep your purchase receipt. In the unlikely event that you need warranty service, call NetMedia at 1-520-544-4567 for a Return Material Authorization (RMA) number.
Page 119 NM-IRJBOX Infrared Illuminator No visible light or red glow The NetMedia IRJBOX Infrared (IR) Illuminator provides invisible light for IR (940nm) sensitive cameras. It enables cameras such as NetMedia’s SC53 to see in complete darkness. The illuminator mounts in a wall with its bracket or in a typical single gang junction (light switch) box.
Page 120 One Year Limited Warranty NetMedia, Inc. warrants this product to be free from defects in materials and workmanship under normal use and service for One Year from the date of purchase or NetMedia will repair or, at its option, replace the defective product. Please keep your purchase receipt. In the unlikely event that you need warranty service, call NetMedia at 1-520-544-4567 for a Return Material Authorization (RMA) number.
Page 121 NM-ACB3 Cable Box Bypass Kit Passes modulated signals directly to TV Use the NetMedia ACB3 Cable Box Bypass/Combiner Kit to pass a modulator signal to the TV tuner without disrupting the output of a digital or analog cable box. Most cable boxes will only tune cable service signals. Therefore, the TV must be used instead of the cable box to tune other signals.
Page 122 One Year Limited Warranty NetMedia, Inc. warrants this product to be free from defects in materials and workmanship under normal use and service for One Year from the date of purchase or NetMedia will repair or, at its option, replace the defective product.Please keep your purchase receipt.
Page 123 NM-CNF7080 RF Notch Filter Removes Cable Channels 70-80 The NetMedia CNF7080 RF Notch Filter removes cable channels 70-80 (UHF 19-29) to allow insertion of up to 6 custom modulated sources (ch. 70, 72, 74, 76, 78, 80). This range is ideal for deletion because it has the fewest analog channels and does not typically interfere with digital services.
Page 124 One Year Limited Warranty NetMedia, Inc. warrants this product to be free from defects in materials and workmanship under normal use and service for One Year from the date of purchase or NetMedia will repair or, at its option, replace the defective product.Please keep your purchase receipt.
Page 125 MPEG-4 Video Web Server NM-VIDSERVER-1 Single port A/V to Ethernet device The NetMedia VIDSERVER-1 is a streaming MPEG-4 digital media server which enables A/V sources to distribute compressed live audio and video over Ethernet to The Internet or a local intranet. It is a self-contained web server so all management, configuration, and monitoring is performed through a Microsoft Windows PC using Internet Explorer.
Page 126 One Year Limited Warranty NetMedia, Inc. warrants this product to be free from defects in materials and workmanship under normal use and service for One Year from the date of purchase or NetMedia will repair or, at its option, replace the defective product. Please keep your purchase receipt. In the unlikely event that you need warranty service, call NetMedia at 1-520-544-4567 for a Return Material Authorization (RMA) number.
Page 127: Video Switcher
4 X 1 Video Switcher Sequence 2 to 4 Inputs through 1 Output The NetMedia VS4X1 Video Switcher allows 2 to 4 baseband video sources to be sequenced through 1 output. Great for surveillance and monitoring in commercial, residential, and specialty applications.
Page 128 Installation of the VS4X1 Video Switcher Thank you for purchasing the NetMedia 4X1 Video Switcher. This unit comes factory set to automatically switch between 4 video sources every 4 seconds (4 sec. per source). If there are fewer video sources or you wish to change the 4 second time lapse, follow the instructions below.
Page 129 4 X 4 Video Matrix Switcher Sequence 1 to 4 Inputs through 1 to 4 Outputs The NetMedia VS4X4 Matrix Switcher allows any combination of 1 to 4 baseband video sources to be independently sequenced through any of 1 to 4 possible outputs. Great for surveillance and monitoring in commercial, residential, and specialty applications.
Page 130: Installation
The output may then be sent to a composite video source or modulated (using an RF modulator such as the NetMedia MM70 Micro Modulator, RM70 Remote Modulator or MM73 Triple Play Modulator). In addition to the rotation modes each source may be viewed independently.
Page 131: Troubleshooting Tips
Troubleshooting Tips Video Switcher VS4X1 This table covers the NetMedia Video Switcher VS4X1 Symptom Description Recommended Action VS4X1 does not work. 1. The VS4X1 requires 12V DC 100mA 1. Disconnect and reconnect power supply. Make sure all other connections power and good signal connections. are secure.
Page 132 Intentionally Blank Page...
Page 133 NM-POCSET PoC Encoder/Decoder Set Video and Power Transmission Device The NetMedia Power over Coax PoC Video Encoder and Decoder modules allow popular 12V DC cameras to use one coax cable, such as RG6, for both power and video. There is no need to run multiple cables to the camera location! The modules support cable distances up to 100 feet.
Page 134: Installation Procedures
NM-POCSET Installation Procedures: 1. Connect a coax cable (RG6 recommended) to the F-Connectors of the Video Encoder and Decoder. Each Encoder/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Encoder/Decoder coax to other video distribution equipment! Doing so could damage this product and/or the other attached devices! 2.
Page 135: Fcc Information (U.s.a.)
PoC Encoder/Decoder Set Video and Power Transmission Device FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements. Modifications not expressly approved by NetMedia may void your authority, granted by the FCC, to use the product. Failure to follow all installation instructions could void your FCC authorization to use the product in the USA.
Page 136 Frequently Asked Questions Q-Can I connect the coax between the modules to video distribution equipment? A- NO! Do not connect the F-Connector coax of the Video Encoder or Decoder other video equipment! Doing so could damage this product and/or the other attached devices! The Decoder ouputs DC voltage on the coax that other equipment may not be prepared to handle.
Page 137 NM-UTPSET UTP Encoder/Decoder Set Video and Power Transmission Device The NetMedia UTP Video Encoder and Decoder modules allow popular 12V DC cameras to use Unshielded Twisted Pair (UTP) cable, such as CAT5, for both power and video. There is no need to run multiple cables to the camera location! The modules support cable distances up to 1000 feet.
Page 138 NM-UTPSET Installation Procedures: 1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the Video Encoder and Decoder. Each Encoder/Decoder pair needs a dedicated point-to-point wiring circuit. If attaching your own plugs, wire them for straight-through connec- tions: pin1 to pin1, pin2 to pin2;...
Page 139 UTP Encoder/Decoder Set Video and Power Transmission Device UTP Wiring Information: The UTP cable should be wired for a straight-through connection according to the T-568A specification as shown in Figure 4. FCC Information (U.S.A.): Important: This product, when installed as specified below, meets FCC requirements.
Page 140 Frequently Asked Questions Q- Can I connect the modules to any computer network equipment? A- NO! Do not connect the UTP cable of the Video Encoder or Decoder to a computer network! Doing so could damage the attached devices! The Decoder ouputs DC voltage on pins 7 and 8 of its UTP connector that some network equipment may not be prepared to handle.