cecotec HYDROSTEAM 2030 ACTIVE, 05704 Manual

PARTS AND COMPONENTS

Fig. 1 key:

1. Main body
2. Cable
3. Heat and steam indicator light
4. Hose (not detachable)
5. Steam button
6. Steam safety lock
7. Accessory connector
8. Power button
9. Water tank with safety cap (locking function and safety valve)

Accessories
Fig. 2 key:

1. Floor head
2. Ironing brush cloth
3. Extension tube x2
4. Big nozzle
5. Nylon brush
6. Measuring cup
7. Funnel
8. Ironing brush
9. Brush for glass
10. Floor mop
11. Curve nozzle

NOTE:
the graphics in this manual are schematic representations and may not exactly match the device.

BEFORE USE

• This appliance is packaged in a way as to protect it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the device when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good conditions. If there is any piece missing or in bad conditions, contact the official Cecotec Technical Support Service immediately.

Box content:

• Canister steam cleaner
• Power adapter
• Kit with 12 accessories
• Instruction manual

Note:
Because it is possible that steam may loosen, peel, discolour, deform, or melt the surface to be cleaned, we recommend that you test the heat and moisture resistance of the material to be cleaned by doing a small test on a hidden piece of the surface.

OPERATION

Filling up the water tank

1. Make sure the steam cleaner is switched off and unplugged before filling up the water tank.
2. Remove the safety cap from the water tank.
3. Fill the water tank with the help of the measuring cup (max. 720 mL) and the funnel.
4. Replace the safety cap on the water tank.
   Note: the safety cap cannot be opened while there is pressure inside the steam cleaner.
5. Drain all steam and allow to cool before opening. Warnings:

• To extend the life of the steam cleaner, we recommend that you use a mixture of tap water and unscented, weakly mineralised water without additives (1:1).
• Never use pure demineralised water, water from a tumble dryer or water softener, or rainwater.

Filling up the water tank during use

Wait until the steam cleaner stops producing steam and make sure there is no pressure inside before removing the safety cap (a special protective device prevents the safety cap from opening while there is pressure inside the steam vacuum cleaner).

1. Press the steam button to spray steam until the tank is empty.
2. Release the button and open the safety cap. Be careful, it may emit steam when opening.
3. Fill up the water tank.

Using the device

1. Plug the steam cleaner into a power socket.
2. Press the power button.
3. The indicator light will light up. The steam cleaner is ready to generate steam when the indicator light changes from orange to green.
4. Remove the steam safety lock and press the steam button on the gun handle to generate steam.
5. After use, press the steam button for a few seconds to finish releasing water condensation from the hose.

• Do not direct the steam jet at people, animals, electrical connectors, electrical units, or devices, or at the appliance itself.
• Do not change the accessories while steaming.
• Before cleaning delicate surfaces, such as carpets or fabrics, we strongly recommend that you perform a test on an inconspicuous area. Wait for the steam to take effect and check that no colour change or deformation has occurred.

Accessories

Accessories can be installed directly to the accessories connector, or you can use one or two extension tubes as required.

How to use accessories

The floor head is designed to clean large surfaces, such as floors. To use it, simply put the mop on the head, as shown in Figure 3. Fig. 3 key:

1. Clamps to hold the mop
2. Extension tube connector
3. Floor mop

• The big nozzle can be used with or without the extension tubes. The concentrated steam jet increases the cleaning power and removes the most stubborn dirt.
• The nylon brush is connected to the big nozzle. It is suitable for cleaning heavily soiled surfaces or bathrooms.
• The ironing brush is mounted with the cloth and can be used with or without the extension tube. This accessory is designed to clean dirt from textile surfaces such as sofas, cushions and more.
• The glass brush is used to remove dirt and stains from glass and glass surfaces.
• Warning: when using the glass brush on cold windows, we advise you to preheat the surface beforehand to prevent damage to the surface. To do this, spray steam about 30 centimetres from the glass.

Switching off the device

Use the power button to switch off the steam cleaner.

Disconnect the appliance from the power supply and allow it to cool down completely before storing it.

CLEANING AND MAINTENANCE

• Unplug the steam cleaner from the mains and let it cool down before cleaning or storing it.
• Clean dirt from the surface and ventilation holes of the steam cleaner periodically. Use a soft, damp cloth to clean the surface of the steam cleaner.
• If not in use for a long period of time, clean and store the steam cleaner in a safe and dry place.
• Do not use abrasive cleaning agents or abrasive sponges as they may damage the product. - The power cable should not be in contact with sharp edges, and it should not be compressed by heavy objects. Store the cord in a clean, dry location always away from metal objects.
• Do not place any heavy items on top of appliance during storage as this may result in possible damage of appliance.

TECHNICAL SPECIFICATIONS

Product: HydroSteam 2030 Active

Product reference: 05704 Voltage: 220-240 V~

Frequency: 50/60 Hz

Power: 2000 W

Tank capacity: 0.75 L

Pressure 4 bars

Technical specifications may change without prior notification to improve product quality.

TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.

It is recommended that repairs be carried out by qualified personnel.

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cecotec Technical Support Service at +34 96 321 07 28.