Advertisement
Your safety, and the safety of others, is very important. To help you make informed decisions about
safety, we have provided installation and operating instructions and other information on labels and in
this guide. This information alerts you to potential hazards that could hurt you or others. It is not possible
to warn you about all potential hazards associated with this product, you must use your own good judg-
ment.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT
DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUC-
TIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT.
This guide identifies potential hazards and has important safety messages that help you and others avoid
personal injury or death. WARNING and CAUTION are signal words that identify the level of hazard. These
signal words mean:
WARNING signals a hazard that could cause serious injury or death, if you do not follow recom-
mendations.
CAUTION signals a hazard that may cause minor to moderate injury, if you do not
follow recommendations.
This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize
general information worthy of special attention.
Failure to observe these instructions could lead to severe injury or death.
Always use extreme caution when cutting and trimming during fitting.
Always remove jewelry and wear eye protection.
Always use appropriate and adequate care in lifting components into place.
Always insure components will remain secure during installation and operation.
Always tighten all nuts and bolts securely, per the installation and operation.
Always perform regular inspections and maintenance on the bumper and related hardware.
Never operate this WARN product with damaged or missing parts.
NOTES
Instructions for mounting accessory trail lights are included on page 6.
I. TABLE OF CONTENTS
Parts List
Tools Required
Torque Specifications
Installation
Maintenance/Care
WARN INDUSTRIES
©2005 Warn Industries, Inc.
WARN® and the WARN logo are trademarks of Warn Industries Inc.
INSTALLATION INSTRUCTIONS
BUMPER KIT
Part Number: 83338
Application: 2009 + Kawasaki 750i Brute Force
WARNING
INJURY HAZARD
page 2
page 2
page 2
page 3-6
page 6
PAGE 1
83339A0
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Warn 83338
Summary of Contents for Warn 83338
- Page 1 This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judg- ment.
-
Page 2: Parts List
30 lb. ft. (40.7 N-m) - 7/16” Wrench 7/16 50 lb. ft. (67.8 N-m) - 1/2 Wrench 75 lb. ft. (101.7 N-m) WARN INDUSTRIES PAGE 2 83339A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc. -
Page 3: Installation
Loosely fasten the center frame bracket to the under- side of the bumper before you install the bumper for ease in placement. Figure 3 WARN INDUSTRIES PAGE 3 83339A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc. - Page 4 Tighten the u-bolt at this time as it will help position the bumper to the vehicle shown in Figure 6. Figure 6 WARN INDUSTRIES PAGE 4 83339A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
- Page 5 Figure 9. Figure 9 PROCEED TO SECTION TITLED “MAINTENANCE/CARE”. WARN INDUSTRIES PAGE 5 83339A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
-
Page 6: Maintenance & Care
URE WHICH MAY RESULT IN VEHICLE DAMAGE AND OPERATOR INJURY OR DEATH. DOUBLE CHECK THAT ALL BOLTS ARE SECURELY TIGHTENED PRIOR TO USE. WARN INDUSTRIES PAGE 6 83339A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
Need help?
Do you have a question about the 83338 and is the answer not in the manual?
Questions and answers