Download Print this page

Belson Outdoors DP-1003HP-L Instruction Sheet

Header pak pet waste disposal station

Advertisement

Quick Links

Model # DP-1003HP-L
1.
Select a good visible spot in your community
or park where you want to install the Aluminum
DOGIPOT HEADER PAK Pet Station.
2.
Prior to installation, remove the 1 3/4" x 1 3/4" x 4' portion
of the mounting post from the 2" x 2" x 4' portion of the
mounting post before cementing. Insert the larger portion
of the mounting post (2" x 2" x 4') approx. 14" into an 18"
deep by 8" diameter hole lled with a 40lb. bag of "ready
to use" concrete mix. To stabilize the post while cementing
place a rod, bolt or other device through the two bottom
holes, prior to inserting into the ground and cementing.
Level the post in a straight vertical position and let
concrete dry for at least 12 hours.
3.
After the concrete is dry, insert the smaller portion of the
post (1 3/4" x 1 3/4" x 4') into the larger cemented portion
of the post (2' x 2' x 4') until the rst 4 holes are lined up
between the two posts. Use two (2) carriage bolts, washers
and locknuts to x the telescope post in position, the upper
bolt in the top overlapping hole, pointing from right to left
and the lower bolt in the bottom overlapping hole, pointing
from front to back. The total height above ground with both
post parts should now be approx. 6'6".
4.
Start by installing the DOGIPOT Pet Sign on top of the 1 3/4"
post, with the upper hole matching the most upper hole in the
square post using the enclosed 2 1/2" bolts, washers and
locknuts. Continue installing the Aluminum DOGIPOT HEADER
PAK Junior Bag Dispenser according to the mounting instructions
enclosed with the Dispenser, ensuring that the upper edge of the
Dispenser is approx. 1" below the lower edge of the DOGIPOT Pet
Sign.
HEADER PAK PET WASTE DISPOSAL STATION
Contents:
(1) Aluminum DOGIPOT Pet Sign
(1) Aluminum DOGIPOT HEADER PAK
Junior Bag Dispenser
(2) Keys for Dispenser Lock Front Access
(1) Channel Post - 1¾" x 1¾" to 2" x 2"
(4) Pet Litter Bag Rolls
100 Count Per Roll - pre-installed
(1) Box OXO-Biodegradable DOGIPOT
Liner Trash Bags (50 Count)
(1) 10 Gallon Steel Trash Receptacle
(1) Galvanized Steel Telescopic Mounting Post
Mounting Hardware:
(1) 2-1/2" Bolt, Washer & Locknut
(1) 2-3/4" Bolt, Washer & Locknut
(2) 2-1/2" Carriage Bolts, Washers & Locknuts
(2) 2-1/4" Tap Bolts, Washers & Locknuts
www.belson.com
627 Amersale Drive
Naperville, IL 60563
Phone: (800) 323-5664
Fax: (630) 897-0573
sales@belson.com
Instructions Sheet

Advertisement

loading
Need help?

Need help?

Do you have a question about the DP-1003HP-L and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Belson Outdoors DP-1003HP-L

  • Page 1 627 Amersale Drive Naperville, IL 60563 Phone: (800) 323-5664 Fax: (630) 897-0573 sales@belson.com Model # DP-1003HP-L Instructions Sheet HEADER PAK PET WASTE DISPOSAL STATION Select a good visible spot in your community Contents: (1) Aluminum DOGIPOT Pet Sign or park where you want to install the Aluminum DOGIPOT HEADER PAK Pet Station.
  • Page 2 Install the Steel DOGIPOT Trash Receptacle through the pre-drilled top oval holes in the back wall of the receptacle and through the square post with the remaining bolts, washers and locknuts, using the 23⁄4” bolt on top and the 21⁄2” bolt below. The upper edge of the trash receptacle must be approximately 121⁄2”...