Subscribe to Our Youtube Channel
Related Manuals for Duplo DT-900
Summary of Contents for Duplo DT-900
- Page 1 Duplo DT-900 Paper Tabber Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 2 DT-900 Inline Tabber with DF915/920 Operation Manual Duplo U.S.A. Corporation Revision 1.45 3050 S. Daimler Street 12/12/2005 Santa Ana, CA. 92705 Tel : 949-752-8222 Fax: 949-752-7766...
-
Page 4: Table Of Contents
Table of Content SECTION 1............................4 Introduction to the DT-900 Inline Tabber ....................4 General Description ............................... 4 Specifications................................. 4 Major Components and assemblies ........................5 SECTION 2............................6 Becoming familiar with the control panel ....................6 Control Panel ................................. 6 Reference for Control Panel functions........................ -
Page 5: Section 1
Introduction to the DT-900 Inline Tabber General Description The DT-900 is designed to be operational inlined with Duplo’s DF-915 & DF-920 folders to apply either 1 or 2 tabs on the open end of the media. The type of tab this tabber supports is pin fed with 1”... -
Page 6: Major Components And Assemblies
Major Components and assemblies Side view of machine Tab Spool Holder Safety cover handles Locking handle Arm Assy. Tractor Assy. Flipper Plate Take- up Spool clip... -
Page 7: Section 2
SECTION 2 Becoming familiar with the control panel Control Panel Figure 1 Reference for Control Panel functions Keys Operation • Start the tabber. Press • Stop the tabber. Press • Allow one media to pass without tabbing. Press... - Page 8 • Display current batch count setting. Press & hold down = batch count amount • Turn batch count on/off. Press & hold down and press • Set batch count amount. Press & hold down and press • Clear paper path. Press &...
- Page 9 • Fine tune tab position. Press & hold down and press • Display current speed setting. Press & hold down • Select speed. Speed 1 = slow Press & hold down and press Speed 2 = fast • Clear error. Press •...
-
Page 10: Section 3
Tab Liner from the corresponding Tractor Head. Turn off then back on to initialize the sensors. The DT-900 will detect only one tab liner installed on the Tractor Assy.. The procedure for dual tabbing is the same, except use 2 tab liners, 1 for each tractor head. - Page 11 Routing the liner downward 2. Insert the Tab Liner through Figure 3 the slot on top of Safety Cover “A”. 3. Open Safety Covers “A” & “B”. 4. Open Tractor Assy. Front Gates. Refer to figure 4. 5. Unlock the tractor lock lever and slide to desired position.
-
Page 12: Routing Liner Upward
8. Press & hold down “Tab” and “Reset” for 2 seconds. This will feed the liner through the gap between Separator Bar and Tab Deflector. If the liner didn’t feed between the separator and deflector then do this manually. Figure 5 Locking Handle Liner... -
Page 13: Fine Tune Tab Position
tab into position and ready for separation. To double check its position, the top of the first tab should be at level with the Upper Shroud Assy. (Figure 6). If the first tab is too far away from this position, it may cause jams. Fine tune tab position 16. -
Page 14: Fine Tuning Flat Tab
Refer to Figure 7 for the location of the take up spool shaft. There is an inner counter in the DT-900 that will STOP OPERATION of the machine every time the counter accumulates 5,000 tabs. The LED display will flash and show “FULL”... -
Page 15: Tab Out Detection
Tab out detection There are “Tab out” detecting sensor installed on each Tractor Assy, the tabber will automatically stop when any tab roll is empty. Error recovery → Press & hold down “ ” or “←” to clear media inside the tabber. If the jam is too difficult to clear, then open cover and remove media manually. -
Page 16: Section 4
SECTION 4 Operators Trouble Shooting Guide Error Message/Status Symptom Solutions 1. “E2/E3/E4 Er” 1. Paper on the path when 1. Remove media. turn on the machine. 2. Sensor detects infra red. 2. Keep machine away from infra red emitting light. 2.
Need help?
Do you have a question about the DT-900 and is the answer not in the manual?
Questions and answers