Table of Contents
Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS FOR 9B53 PORTABLE ONLY SHELTER FRAME
*THIS UNIT MUST BE ASSEMBLED BY A MINIMUM OF TWO QUALIFIED PERSONS*
NOTICE Sunlight reflecting off polycarbonate panels can contribute to increased temperatures of
surrounding objects. In certain situations, these increased temperatures can damage some artificial turf
surfaces. Kwik Goal is not responsible for any damage to artificial turf.
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or
damp packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
NOTE: Components may be packaged in one or more additional boxes.
Parts
PART #
SHELTER WIDTH
UZ1559
30'
362-3/8"
UZ1116
24'
287-3/4"
UZ1433
21'
250-7/16"
UZ1434
18'
213-1/8"
UZ1435
15'
175-13/16"
UZ1436
12'
138-1/2"
UZ1114
9'
101-3/16"
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL'S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
Crossbar
(Part# SEE TABLE)
(A)
DIM (A)
QTY
1
1
1
2
2
2
2
140 Pacific Drive Quakertown, PA 18951
800-531-4252 Kwikgoal.com
©
Swivel Wheel Mount
PART #
UZ1577
UZ1444
UZ1443
2015, Rev 2019 Kwik Goal Ltd.
Bottom Crossbar
(Part# SEE TABLE)
(A)
SHELTER WIDTH
DIM (A)
30'
362-3/8"
24'
287-3/4"
21'
250-7/16"
QTY
1
1
1
NZ374 Rev. 12/04/19
Advertisement
Table of Contents
Related Manuals for KwikGoal 9B53
Summary of Contents for KwikGoal 9B53
- Page 1 ASSEMBLY INSTRUCTIONS FOR 9B53 PORTABLE ONLY SHELTER FRAME *THIS UNIT MUST BE ASSEMBLED BY A MINIMUM OF TWO QUALIFIED PERSONS* NOTICE Sunlight reflecting off polycarbonate panels can contribute to increased temperatures of surrounding objects. In certain situations, these increased temperatures can damage some artificial turf surfaces.
- Page 2 OR PULL 90 Person at Post NO PUSH PUSH OR PULL OR PULL 90 WITHIN 120 NEVER LEAVE SHELTERS UNATTENDED AND UNSECURED 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2015, Rev 2019 Kwik Goal Ltd. NZ374 Rev. 12/04/19...
-
Page 3: Table Of Contents
Parts Continued Right Post (1) Left Post (1) (Part# UZ1439) (Part# UZ1439) 55-3/16” 55-3/16” Date of manufacture sticker Post Corner (2) Crossbar Corner (2) Left Base (1) Right Base (1) (Part# UZ1442) (Part# UZ1211) (Part# UZ1441) (Part# UZ1440) 50-1/8” 50-1/8” Center Panel (SEE TABLE) Left Panel (1) Right Panel (1) - Page 4 Note: Hardware is packed separately in one or more boxes. Open all boxes and layout all sealed hardware packs before beginning assembly. Anchor Hdw Frame Hdw (Part# JZ217) (Part#JZ190) 3/8” X 1” Socket Head (20) (Part# TZ323) 7/16” Flat Washer (Part# TZ171) 3/8”...
- Page 5 3. Hardware for this step is in Frame Hdw & Panel Hdw packs. Assemble crossbar, bases, and post corners. Press joints together firmly before tightening bolts. NOTE: Square nuts will float loose in channels until used later. 3/8” Square Nut Left Base 3/8”...
-
Page 6: Date Of
4. Hardware for this step is in Frame Hdw & Panel Hdw packs. Assemble crossbar, posts, and crossbar corners. Press joints together firmly before tightening bolts. NOTE: Square nuts will float loose in channels until used later. 3/8” x 1” Socket Head Cap Screw 3/8”... -
Page 7: Post Corner
5. Hardware for this step is in Frame Hdw & Panel Hdw packs. Insert one 3/8” square nut in each side of assembled base corner. Connect assembled base and post as shown. Press joints together firmly before tightening bolts. Assembled Base Assembled Post Assembled Base Assembled Post... -
Page 8: Left Panel
6. Hardware for this step is in Panel Hdw packs. Attach right and left panels to assembled frame as shown. Do NOT tighten bolts at this time. 3/8” x 7/8” Hex Bolt - make finger tight to temporarily hold square nut in place. 3/8”... - Page 9 7. Install swivel wheels - 10” diameter tires. Note suggested location of brakes as shown below. 5/16” Flat Washer 5/16” Lock Washer 5/16” x 1” Hex Bolt Base Swivel Wheel w/ Brake 5/16” Flat Washer 5/16” Lock Washer 5/16” x 1” Hex Bolt Base Swivel Wheel THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES...
- Page 10 8. Turn shelter frame onto base and remove temporary 3/8” X 7/8” bolt then connect bottom of right and left panel as shown. Left Panel Do NOT tighten bolts at this time. Assembled Frame Right Panel Left Panel Right Panel Assembled Frame 3/8”...
- Page 11 9. Hardware for this step is in Panel Hdw packs. Insert double end studs into left panel. Move unneeded square nuts in top and bottom crossbars away from left side at least one center panel width. Do NOT tighten bolts at this time. Left Panel Double End Stud Double End Stud...
- Page 12 10. Hardware for this step is in Panel Hdw packs. Line up square nut with holes in center panel and attach center panel to shelter frame. Slide center panel to mate with left panel lining up double end studs, as shown. Repeat steps 9 & 10 to attach center panel to the right side.
- Page 13 11. Hardware for this step is in Panel Hdw packs. Repeat step 10 to attach center panels to crossbars then connect center panels together until the only 1 center panel is left. Remember to move unneeded square nuts on top and bottom crossbars out from under the center panel being attached before bolting center panel in place.
- Page 14 12. If installing Bench or Molded Seating, skip to step 13. If installing Luxury Seating, tighten all panel joint bolts. Begin at center joint and work outward. Tighten 3 bolts per joint. Tighten 3 panel frame bolts on each of the left and right end panels. Tighten panel to frame bolts at top and bottom of each center panel.
- Page 15 13. Hardware for this steps 13 and 14 is in Anchor Hdw pack. Attach anchor chain to shelter frame, 2 in the front on the outside and 2 on the inside at the back as shown. Assembled Shelter Frame 7/16” Lock Nut 7/16”...
- Page 16 Permanent ground anchors must be used at all times. Dig four holes according to the layout below. Note: areas subject to heavy frost may require depths as deep as 36”. Prepare hole and add drain stone as shown. Install anchor in each hole and fill hole with concrete.
-
Page 17: Polycarbonate
Lower Brace Line (31”) Polycarbonate Go to kwikgoal.com for additional product information. THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS. - Page 18 Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or damp packaging may damage contents. 2. Refer to 9B53 instructions to assemble shelter frame prior to beginning seat assembly. 3. Read through entire instruction before beginning assembly and installation.
- Page 19 OR PULL 90 Person at Post NO PUSH PUSH OR PULL OR PULL 90 WITHIN 120 NEVER LEAVE SHELTERS UNATTENDED AND UNSECURED 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2015, Rev 2019 Kwik Goal Ltd. NZ379 Rev 12/04/2019...
- Page 20 Parts Continued Molded Seat Crossbar Front Seat Frame Plate (SEE TABLE) (Part# SEE TABLE) (Part# UZ1107) MODEL# 9B5320 9B5328 Black Dot Sticker 9B5327 MODEL# PART# DIM (A) 9B5326 9B5320 UZ1601 167-1/4” 9B5325 9B5320 UZ1603 189” 9B5324 9B5328 UZ1452 288” 9B5327 UZ1461 250”...
- Page 21 Parts Continued Hardware needed per Model 9B5323 9B5324 9B5325 9B5326 9B5327 9B5328 9B5320 1/4” X 2-3/4” Hex Bolt (15) (21) (24) (30) (36) (42) (51) (Part# TZ18) 1/4” Flat Washer (30) (42) (48) (60) (72) (84) (102) (Part# TZ147) 1/4” Lock Nut (15) (21) (24)
- Page 22 5. 9B5320 - skip to step 12, for all other models continue with step 6. 6. Start at each end and attach seat frame plates to assembled shelter panels as shown. Attach remaining seat frame plates to assembled shelter panels at needed locations, do not exceed two panels between seat frame plates.
- Page 23 7. Attach seat frames at seat frame plate locations, do not over tighten bolts. Assembled Center Panel Uprights Tighten These Bolts First Tighten nuts only until flush with end of bolts. Bench frames must pivot up & down freely. Seat Frame with Seat Swivel Wheel Center Panel Uprights 3/8”...
- Page 24 8. Tighten all panel joint bolts. Begin at center joint and work outward. Tighten 3 bolts per joint. Tighten 3 panel frame bolts on each of the left and right end panels. Tighten panel to frame bolts at top and bottom of each center panel.
- Page 25 9. Center the shelf plank at location shown. Attach shelf plank to each seat frame. Align bench hold down parallel with slot in shelf plank, insert, and turn ninety degrees (quarter turn) to attach shelf plank to seat frame. Shelf Plank Seat Frame NOTE: DO NOT TIGHTEN ANY BOLTS AT THIS TIME.
- Page 26 10. Attach molded seat crossbar front and rear to seat frames and seat supports. Note: Make sure colored dots on molded seat crossbars are located as shown. Tighten shelf plank bolts at this time. (CAUTION DO NOT OVER TIGHTEN BOLTS.) Molded Seat Crossbar Front Molded Seat Crossbar Rear Seat Support...
- Page 27 11. Starting at one end, attach molded seats to molded seat crossbars. After all molded seats are attached to molded seat crossbars, tighten all seating bolts. (CAUTION DO NOT OVER TIGHTEN BOLTS.) Molded Seats Molded Seat Crossbars Molded Seat 1/4” x 2-3/4” Hex Bolt 1/4”...
- Page 28 12. Start at each end and attach seat frame plates to assembled shelter panels as shown. Attach remaining seat frame plates to assembled shelter panels at needed locations, do not exceed two panels between seat frame plates. Do not tighten bolts at this time. NOTE: It may be necessary to loosen panel bolts to allow frame plate bolts to be inserted.
- Page 29 13. Attach seat frames at seat frame plate locations, do not over tighten bolts. Assembled Center Panel Uprights Tighten These Bolts First Tighten nuts only until flush with end of bolts. Bench frames must pivot up & down freely. Seat Frame with Seat Swivel Wheel Center Panel Uprights 3/8”...
- Page 30 14. Tighten all panel joint bolts. Begin at center joint and work outward. Tighten 3 bolts per joint. Tighten 3 panel frame bolts on each of the left and right end panels. Tighten panel to frame bolts at top and bottom of each center panel.
- Page 31 15. Center the shelf planks at location shown. Attach shelf plank to each seat frame. Align bench hold down parallel with slot in shelf plank, insert, and turn ninety degrees (quarter turn) to attach shelf plank to seat frame. Shelf Plank Shelf Plank Seat Frame NOTE: DO NOT TIGHTEN ANY BOLTS AT THIS TIME.
- Page 32 16. Attach molded seat crossbar front and rear to seat frames and seat supports. Note: Make sure colored dots on molded seat crossbars are located as shown below, do not overtighten bolts. Tighten shelf plank bolts at this time. Molded Seat Crossbar Front Molded Seat Crossbar Rear Seat Support Seat Frame...
- Page 33 1/4” Lock Nut Molded Seat Crossbar Front Go to kwikgoal.com for additional product information. THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
Need help?
Do you have a question about the 9B53 and is the answer not in the manual?
Questions and answers