Table of Contents
Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS FOR ALL 9B55 PORTABLE ONLY SHELTER FRAMES
*THIS UNIT MUST BE ASSEMBLED BY A MINIMUM OF TWO QUALIFIED PERSONS*
NOTICE Sunlight reflecting off polycarbonate panels can contribute to increased temperatures of
surrounding objects. In certain situations, these increased temperatures can damage some artificial turf
surfaces. Kwik Goal is not responsible for any damage to artificial turf.
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or
damp packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
NOTE: Components may be packaged in one or more additional boxes.
Parts
PART #
SHELTER WIDTH
UZ1559
30'
UZ1116
24'
UZ1433
21'
UZ1434
18'
UZ1435
15'
UZ1436
12'
UZ1114
9'
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE
WARNING
OR IN THE THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL
NOT BE COVERED UNDER KWIK GOAL'S PRODUCT GUARANTEE. DO NOT LEAVE THIS
EQUIPMENT UNATTENDED.
Crossbar
(Part# SEE TABLE)
(A)
DIM (A)
QTY
362-3/8"
1
287-3/4"
1
250-7/16"
1
213-1/8"
2
175-13/16"
2
138-1/2"
2
101-3/16"
2
140 Pacific Drive Quakertown, PA 18951
800-531-4252 Kwikgoal.com
©
2019, Rev 2023 Kwik Goal Ltd.
Swivel Wheel Mount
PART #
SHELTER WIDTH
UZ1577
30'
UZ1444
24'
UZ1443
21'
Bottom Crossbar
(Part# SEE TABLE)
(A)
DIM (A)
QTY
362-3/8"
1
287-3/4"
1
250-7/16"
1
NZ432 Rev. 01/24/23
Advertisement
Table of Contents
Related Manuals for KwikGoal 9B55
Summary of Contents for KwikGoal 9B55
- Page 1 ASSEMBLY INSTRUCTIONS FOR ALL 9B55 PORTABLE ONLY SHELTER FRAMES *THIS UNIT MUST BE ASSEMBLED BY A MINIMUM OF TWO QUALIFIED PERSONS* NOTICE Sunlight reflecting off polycarbonate panels can contribute to increased temperatures of surrounding objects. In certain situations, these increased temperatures can damage some artificial turf surfaces.
- Page 2 OR PULL 90 Person at Post NO PUSH PUSH OR PULL OR PULL 90 WITHIN 120 NEVER LEAVE SHELTERS UNATTENDED AND UNSECURED 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2015, Rev. 2019 Kwik Goal Ltd. NZ432 Rev. 01/24/23...
-
Page 3: Table Of Contents
Parts Continued Right Post (1) Left Post (1) (Part# UZ1439) (Part# UZ1439) 55-3/16” 55-3/16” Date of manufacture sticker Post Corner (2) Crossbar Corner (2) Left Base (1) Right Base (1) (Part# UZ1442) (Part# UZ1211) (Part# UZ1611) (Part# UZ1610) 76-1/4” 76-1/4” Left Panel (1) Right Panel (1) Center Panel (SEE TABLE) - Page 4 Note: Hardware is packed separately in one or more boxes. Open all boxes and layout all sealed hardware packs before beginning assembly. Anchor Hdw Frame Hdw (Part#JZ190) (Part# JZ217) 3/8” X 1” Socket Head (20 ) (Part# TZ323) 7/16” Flat Washer (Part# TZ171) 3/8”...
- Page 5 3. Hardware for this step is in Frame Hdw & Panel Hdw packs. Assemble crossbar, bases, and post corners. Press joints together firmly before tightening bolts. NOTE: Square nuts will float loose in channels until used later. 3/8” Square Nut Left Base 3/8”...
-
Page 6: Date Of
4. Hardware for this step is in Frame Hdw & Panel Hdw packs. Assemble crossbar, posts, and crossbar corners. Press joints together firmly before tightening bolts. NOTE: Square nuts will float loose in channels until used later. 3/8” x 1” Socket Head Cap Screw 3/8”... -
Page 7: Post Corner
5. Hardware for this step is in Frame Hdw & Panel Hdw packs. Insert one 3/8” square nut in each side of assembled base corner. Connect assembled base and post as shown. Press joints together firmly before tightening bolts. Assembled Base Assembled Post Assembled Base Assembled Post... -
Page 8: Left Panel
6. Hardware for this step is in Panel Hdw packs. Attach right and left panels to assembled frame as shown. Do NOT tighten bolts at this time. 3/8” x 7/8” Hex Bolt - make finger tight to temporarily hold square nut in place. 3/8”... - Page 9 7. Install swivel wheels - 10” diameter tires. Note suggested location of brakes as shown below. 5/16” Flat Washer 5/16” Lock Washer 5/16” x 1” Hex Bolt Base Swivel Wheel w/ Brake 5/16” Flat Washer 5/16” Lock Washer 5/16” x 1” Hex Bolt Base Swivel Wheel THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES...
- Page 10 8. Turn shelter frame onto base and remove temporary 3/8” X 7/8” bolt then connect bottom of right and left panel as shown. Do NOT tighten bolts at this time. Left Panel Right Panel Assembled Frame 3/8” x 7/8” Hex Bolt 3/8”...
- Page 11 9. Hardware for this step is in Panel Hdw packs. Insert double end studs into left panel. Move unneeded square nuts in top and bottom crossbars away from left side at least one center panel width. Do NOT tighten bolts at this time. Left Panel Double End Stud Top Crossbar...
- Page 12 10. Hardware for this step is in Panel Hdw packs. Line up square nut with holes in center panel and attach center panel to shelter frame. Slide center panel to mate with left panel lining up double end studs, as shown. Repeat steps 9 & 10 to attach center panel to the right side.
- Page 13 11. Hardware for this step is in Panel Hdw Center Panel packs. 5/16” x 3- 3/4” Hex Bolt Repeat step 9 to attach center panels to crossbars then connect center panels 5/16” Flat Washer together until the only 1 center panel is left.
- Page 14 12. Before installing last center panel, tighten 4 bolts at each center panel joint. Then tighten 4 lock nuts at left and right end panel joints. 13. Install last center panel to shelter frame. After all bolts are installed, go back and tighten 8 center panel joint bolts on the last panel.
- Page 15 16. Hardware for steps 16 and 17 are in the Anchor Hdw pack. Attach anchor chain to shelter frame, 2 in the front on the outside and 2 on the inside at the back as shown. Assembled Shelter Frame 7/16” Lock Nut 7/16”...
- Page 16 Permanent ground anchors must be used at all times. Dig four holes according to the layout below. Note: areas subject to heavy frost may require depths as deep as 36”. Prepare hole and add drain stone as shown. Install anchor in each hole and fill hole with concrete.
- Page 17 18. If desired, panel joints may be sealed with a small bead of urethane sealant. Seal across crossbar to panel joint, then panel to panel joints. NOTE: Panel to panel joints should only be sealed between crossbar and lower brace of panels. Sealant below lower brace line is not necessary.
- Page 18 9B543-03 9B543-04 9B543-03 9B543-05 Go to kwikgoal.com for additional product information. THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE WARNING OR IN THE THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S PRODUCT GUARANTEE.
- Page 19 (Part# UZ1585) (Part# VZ802) (Part # UZ1675) Frame Plate (2) Handle (2) Seat Deck Stop (4) (Part# UZ1591) (Part# VZ679) (Part# VZ838) 47-3/4” 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2021, Rev 2023 Kwik Goal Ltd. NZ455-01 Rev. 03/15/23...
- Page 20 RT & LT 2nd Row Seat Deck Hdw (JZ274) Molded Seat Crossbar Front (2) Note: Hardware may be packaged separately (Part# UZ1678) in one or more boxes. Open all packages before beginning assembly. Green Dot Sticker 1/4“ x 1” Hex Bolt (Part# TZ373) 1/4“...
-
Page 21: Frame Plate
4. Attach frame plate to deck frame. Typical applications require one left and one right assembly Note: Depending on what side of frame plate faces out will determine a right or left deck assembly. Top of frame plate must be flush or below top of deck frame. For best appearance, snug sidewalk bolts and tighten hex bolts. -
Page 22: Seat Frame
6. Attach seat frames to deck frame as shown. (Do NOT tighten bolts at this time.) Seat Frame 1/4” X 4-3/4” Hex Bolt 1/4” Flat Washer 1/4”Lock Nut 1/4” Flat Washer 7. Attach the front and rear molded seat crossbars to seat frames as shown. Once the molded seat crossbars are attached, tighten the crossbars to the seat frames. - Page 23 8. Attach molded seats to molded seat crossbars. After both molded seats are attached to molded seat crossbars, tighten all seating bolts. (CAUTION DO NOT OVER TIGHTEN BOLTS.) 1/4” X 2-3/4” Hex Bolt 1/4” Flat Washer Remove plastic cover and replace after tighten bolts 1/4”...
- Page 24 Handle 2ND ROW PLACEMENT IN SHELTER FRAME Bottom Crossbar Seat Deck Stop Left Frame 2ND ROW ARRANGEMENT SHELTER FRAME Frame Plate 1-5/8” From Base Left Frame Right Frame Center Frame Go to kwikgoal.com for additional product information. NZ455-01 Rev. 03/15/23...
-
Page 25: 2Nd Row Deck Frame
(Part# UZ1671) (Part# VZ802) (Part # UZ1675) Frame Plate (1) Handle (1) Seat Deck Stop (2) (Part# UZ1590) (Part# VZ679) (Part# VZ838) 49-1/4” 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2021, Rev 2023 Kwik Goal Ltd. NZ455-02 Rev. 03/15/23... -
Page 26: Wheel
Center 2nd Row Seat Deck Hdw (JZ275) Molded Seat Crossbar Front (1) Note: Hardware may be packaged separately (Part# UZ1678) in one or more boxes. Open all packages before beginning assembly. Green Dot Sticker 1/4“ x 1” Hex Bolt (Part# TZ373) 1/4“... -
Page 27: Seat Deck Stop
4. Attach frame plate to deck frame. Note: Top of frame plate must be flush or below top of deck frame. For best appearance, snug sidewalk bolts and tighten hex bolts. 1/4” X 3” Sidewalk Bolt 1/4” Lock Nut Handle 1/4”... - Page 28 6. Attach seat frames to deck frame as shown. (Do NOT tighten bolts at this time.) Seat Frame 1/4” X 4-3/4” Hex Bolt 1/4” Flat Washer 1/4”Lock Nut 1/4” Flat Washer 7. Attach the front and rear molded seat crossbars to seat frames as shown. Once the molded seat crossbars are attached, tighten the crossbars to the seat frames.
- Page 29 8. Attach molded seats to molded seat crossbars. After both molded seats are attached to molded seat crossbars, tighten all seating bolts. (CAUTION DO NOT OVER TIGHTEN BOLTS.) 1/4” X 2-3/4” Hex Bolt 1/4” Flat Washer Remove plastic cover and replace after tighten bolts 1/4”...
- Page 30 Handle 2ND ROW PLACEMENT IN SHELTER FRAME Bottom Crossbar Seat Deck Stop Left Frame 2ND ROW ARRANGEMENT SHELTER FRAME Frame Plate 1-5/8” From Base Left Frame Right Frame Center Frame Go to kwikgoal.com for additional product information. NZ455-02 Rev. 03/15/23...
- Page 31 Wheel (2) (Part# UZ1586) (Part # UZ1674) (Part# VZ802) 49-1/4” 32” Right Wheel Bracket (1) Left Wheel Bracket (1) (Part# UZ1597) (Part# UZ1598) 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2019, Rev 2023 Kwik Goal Ltd. NZ454-03 Rev. 03/15/23...
- Page 32 1st Row Seat Deck Hdw (JZ273) Molded Seat Crossbar Front (1) Note: Hardware may be packaged separately (Part# UZ1678) in one or more boxes. Open all packages before beginning assembly. Green Dot Sticker 1/4“ x 1” Hex Bolt (Part# TZ373) 1/4“...
- Page 33 4. Attach deck to deck frame as shown. (Do NOT tighten bolts at this time.) 1/4” X 1-1/4” Sidewalk Bolt Deck Deck Frame 1/4” Flat Washer 1/4” Lock Nut 5. Attach the seat frames to deck frame as shown. (Do NOT tighten bolts at this time.) Seat Frame 1/4”...
- Page 34 6. Attach the front and rear molded seat crossbars to seat frames as shown. Once the molded seat crossbars are attached, tighten the crossbars to the seat frames. Snug deck to deck frame bolts. (CAUTION DO NOT OVER TIGHTEN BOLTS.) Molded Seat Crossbar Rear 5/16”...
- Page 35 8. Attach wheel assemblies as shown below. Tighten seat frame to deck bolts. Deck to deck frame bolts Seat frame to deck bolts 1/4” x 1-1/2” Hex Bolt 1/4” Lock Washer 1/4” Flat Washer Left Wheel Assembly NZ454-03 Rev. 03/15/23...
- Page 36 9. Recommended seating arrangement shown below. End Aisle Decking Center Aisle Decking End Aisle Decking Go to kwikgoal.com for additional product information. NZ454-03 Rev. 03/15/23...
- Page 37 Phillips Screwdriver before beginning assembly. 7/16” Socket 1/4“ x 1-1/4” Sidewalk (Part# TZ387) 1/4“ Lock Nut (Part# TZ19) 1/4” Flat Washer (Part# TZ147) 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2017, Rev. 2020 Kwik Goal Ltd. NZ422-04 Rev. 06/11/20...
- Page 38 3. Assemble the double aisle deck frame plate to deck frame as shown. 1/4”x 1-1/4” Sidewalk Bolt Deck Deck Frame 1/4” Flat Washer 1/4” Lock Nut 4. Recommended aisle deck arrangement shown below. Double Aisle Decking Go to kwikgoal.com for additional product information. NZ422-04 Rev. 06/11/20...
- Page 39 Phillips Screwdriver before beginning assembly. 7/16” Socket 1/4“ x 1-1/4” Sidewalk (Part# TZ387) 1/4“ Lock Nut (Part# TZ19) 1/4” Flat Washer (Part# TZ147) 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2017, Rev. 2020 Kwik Goal Ltd. NZ422-05 Rev. 06/11/20...
- Page 40 3. Assemble the single aisle deck frame plate to deck frame as shown. 1/4”x 1-1/4” Sidewalk Bolt Deck Deck Frame 1/4” Flat Washer 1/4” Lock Nut 4. Recommended aisle deck arrangement shown below. Single Aisle Decking Single Aisle Decking Go to kwikgoal.com for additional product information. NZ422-05 Rev. 06/11/20...
- Page 41 OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED. 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2018, Rev 2020 Kwik Goal Ltd. NZ430 Rev. 03/29/22...
Need help?
Do you have a question about the 9B55 and is the answer not in the manual?
Questions and answers