Advertisement
Quick Links
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify trucking company immediately. Lay out all parts. Remove all cardboard and packaging immediately.
Wet or damp packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
Parts
Upright (4)
(Part# UZ1278)
Base (4)
(Part# UZ1279)
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL'S LIFETIME GUARANTEE. DO NOT
All Kwik Goal products carry a Lifetime Guarantee. For help with
guarantee issues, visit kwikgoal.com and click on the Lifetime
Guarantee logo or contact customer service at
ASSEMBLY INSTRUCTIONS FOR 7E201 PORTABLE BACKSTOP
186"
WARNING
LEAVE THIS EQUIPMENT UNATTENDED.
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
Bottom Bar (3)
(Part# UZ1280)
Heavy Duty
Anchor Bage (16)
(Part# 10B7011)
2011 Kwik Goal Ltd.
.
1-800-531-4252
234-1/2"
Brace (2)
(Part# UZ1295)
NZ328 Rev. 10/05/11
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for KwikGoal 7E201
Summary of Contents for KwikGoal 7E201
- Page 1 All Kwik Goal products carry a Lifetime Guarantee. For help with guarantee issues, visit kwikgoal.com and click on the Lifetime Guarantee logo or contact customer service at 1-800-531-4252 ASSEMBLY INSTRUCTIONS FOR 7E201 PORTABLE BACKSTOP 1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred, notify trucking company immediately.
- Page 2 Swivel Connector Tube (4) Knob (2) Hardware (Part# UZ1296) (Part#VZ252) Note: Hardware may be packaged separately in one or more boxes. Open all packages before beginning assembly. 8-32 X 5/8” Flat Head Screw (Part# TZ314) 1/4” Flat Washer (Part# TZ147) Rope Cleat (4) 1/4”...
- Page 3 4. Set assembled bases and bottom bars in desired location and connect together. Note: Bases at each end of unit must be connected to the fixed tube of the base assembly. Bottom Bar Square Nut & Stud Assembled Base Fixed Tube Bottom Bar Assembled Base Bottom Bar...
- Page 4 5. Fill each of the 16 heavy duty anchor bags with 40lbs of sand or gravel. Set 4 heavy duty anchor bags on each assembled base as shown. Heavy Duty Anchor Bag Heavy Duty Anchor Bag Assembled Base Assembled Base 6.
- Page 5 7. Lay out uprights as shown and put rope through pulleys on each upright. Tie a snap link to the end of each rope as shown. Pulley Upright Rope Upright Upright Upright Assembled Base with Upright Heavy Duty Anchor Bags Upright Upright Upright...
- Page 6 9. First attach 3/8” X 3” threaded stud to 3/8” X 3” Threaded Stud brace on plate with threaded hole. With 3/8” Flat Washer square nut & stud, attach braces to 3/8” Lock Washer bottom bar using knob & 3/8” lock nut. 3/8”...
- Page 7 11.Hoist net starting at one end and attach net Upright holder to the perimeter rope of net approximately 17” from the top corner. Then Top Corner Tag wrap net holder around upright and attach to the perimeter rope again 17” from the first clip.
- Page 8 13.Complete net raising by hoisting net on two center poles. To secure bottom of net, attach net to bottom bar of backstop with net clips. Place perimeter rope of net in clip and put base of clip into channel and turn 90 degrees to lock into place.
- Page 9 14.This unit can be set up to conform to irregular boundaries, such as arcs. OVER HEAD VIEW 180 TO 90 180 TO 90 Knob 15.After first assembly this unit can be disassembled without any tools. Loosening the knob allows braces to slide in and out of bottom bar. CAUTION: REMOVE NET AND UPRIGHT BEFORE Bottom Bar ADJUSTING ANGLES.
Need help?
Do you have a question about the 7E201 and is the answer not in the manual?
Questions and answers