Ubiquiti LAP-120 Quick Start Manual
  1. Manuals
  2. Brands
  3. Ubiquiti Manuals
  4. Wireless Access Point
  5. LAP-120
  6. Quick start manual
Ubiquiti LAP-120 Quick Start Manual

Ubiquiti LAP-120 Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Package Contents
LiteAP
Set Screws (Qty. 2)
Installation Requirements
7 mm socket wrench or screwdriver
Shielded Category 5 (or above) cabling should be used for all wired Ethernet
connections and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor environments
and destructive ESD events with industrial-grade, shielded Ethernet cable from
Ubiquiti. For more details, visit
Hardware Overview
LAP-120 Quick Start Guide
Ball Joint Mount
Gigabit PoE (24V, 0.5A) with
Mounting Bracket
ui.com/toughcable
Metal Strap
Power Cord

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LAP-120 and is the answer not in the manual?

Questions and answers

Related Manuals for Ubiquiti LAP-120

Summary of Contents for Ubiquiti LAP-120

  • Page 1 LAP-120 Quick Start Guide Package Contents LiteAP Ball Joint Mount Metal Strap Set Screws (Qty. 2) Gigabit PoE (24V, 0.5A) with Power Cord Mounting Bracket Installation Requirements 7 mm socket wrench or screwdriver Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE.

  • Page 2: Hardware Installation

    Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the LiteAP is powered on. Alternatively, the LiteAP may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Adapter. Power LED The Power LED will light blue when the device is connected to a power source.

  • Page 5: Connecting Power

    Connecting Power...
  • Page 6 3. Connect the power using: included Gigabit PoE Adapter PoE switch WARNING: The switch port must comply with the power specifications listed in this Quick Start Guide. Connecting to the PoE Adapter 1. Connect the Ethernet cable from the device to the POE port of the PoE adapter. 2.
  • Page 7 2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included). 4. Align the adapter’s slots with the tabs of the PoE Mounting Bracket, and then slide the adapter down. Accessing airOS Connect to the airOS® Configuration Interface. 1.

  • Page 8: Installer Compliance Responsibility

    5. Create a username and password. Confirm your new password and then click Save. The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For details, refer to the User Guide available at ui.com/download/airmax-ac Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory...

  • Page 9: Specifications

    The Output Power field is provided to the professional installer to assist in meeting regulatory requirements. Specifications LAP-120 Dimensions (Mount Not Included) 452.3 x 78.7 x 54.4 mm (17.81 x 3.10 x 2.14") Weight (Mount Not Included) 420 g (14.82 oz)

  • Page 10: Safety Notices

    Operating Temperature -40 to 70° C (-40 to 158° F) Operating Humidity 5 to 95% Noncondensing Certifications CE, FCC, IC Operating Frequency (MHz) US/CA U-NII-1 5150 - 5250 U-NII-2A 5250 - 5350 U-NII-2C 5470 - 5725 U-NII-3 5725 - 5850 Worldwide 5150 - 5875 Safety Notices...
  • Page 11 ui.com/support/warranty The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

  • Page 12: Australia And New Zealand

    IMPORTANT NOTE Radiation Exposure Statement This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 43 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

  • Page 13: Weee Compliance Statement

    Note: Operation in the 5.8 GHz frequency band is prohibited in BFWA member states. Other countries listed may use the 5.8 GHz frequency band. WEEE Compliance Statement Declaration of Conformity Online Resources © 2021 Ubiquiti Inc. All rights reserved.

Table of Contents