Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Danfoss Synflex Mark IX 4530-009S0
Summary of Contents for Danfoss Synflex Mark IX 4530-009S0
- Page 1 Operator’s Manual Synflex® by Danfoss Mark IX Series Power Swaging Machines...
-
Page 2: Table Of Contents
Maintenance and Component Adjustment Procedures ............ 7 Die Alignment in the Swager Base ..................7 Adjustment of Alignment Rolls ....................7 Replacement Parts ........................8 Troubleshooting ......................... 8 2 | © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. BC445860127079en-000101... -
Page 3: Initial Installation And Setup
This machine is designed expressly for the purpose of swaging Synflex approved couplings and hose together using appropiate Synflex doe sets and pushers. The Danfoss Corporation cannot be responsible for property damage or personal injury that may result from swaging other brands of fittings and hose together nor from the intentional misuse of this device. -
Page 4: Electrical Requirements
Use Renolin AW68 or an equivalent hydraulic fluid that complies with the above requirements. Recommended temperature 125-150° F Maximum temperature 200° F Flash Point 430° F Viscosity (SSU) Viscosity Index 4 | © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. BC445860127079en-000101... -
Page 5: Manual Control Valve Handle Installation
Item 24. WARNING Operating the swager without proper die sets and pushers may cause permanent damage to the cylinder. © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. | 5 BC445860127079en-000101... -
Page 6: Operating Instructions
Always adjust the lift rod collar so that the return stop functions before the pusher block retracts to the bottom of the cylinder. The swager may be damaged otherwise. 6 | © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. BC445860127079en-000101... -
Page 7: Maintenance And Component Adjustment Procedures
Broken components must ne replaced and frame brackets straighten before further damage occurs. © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. | 7 BC445860127079en-000101... -
Page 8: Replacement Parts
Motor runs but cylinder will not cycle Motor runs backwards Check wiring Swaging dies separate during swage Worn or misaligned die base Install components onto new frame 8 | © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. BC445860127079en-000101... - Page 9 Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. | 9 BC445860127079en-000101...
- Page 10 Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual 10 | © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. BC445860127079en-000101...
- Page 11 Adapter 90 3/8" 3A03-06A06 Adapter90 “3/8” ORB Male to 3/8" Female Swivel 3A06-06A06 Adapler 90 “3/8' Male Pipe to 1/4" NSPM Female Swivel 3A03-06A04 © Synflex by Danfoss Mark IX Series Power Swaging Machines Operator’s Manual | 2023.03. | 11 BC445860127079en-000101...
- Page 12 Phone: +86 21 3418 5200w Danfoss can accept no responsibility for possible errors in catalogs, brochures, and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
Need help?
Do you have a question about the Synflex Mark IX 4530-009S0 and is the answer not in the manual?
Questions and answers