Download Print this page

Seneca Z-KEY-2ETH Series Installation Manual

Hide thumbs Also See for Z-KEY-2ETH Series:

Advertisement

Quick Links

PRELIMINARY WARNINGS
The word WARNING preceded by the symbol
The word ATTENTION preceded by the symbol
connected equipment. The warranty shall become null and void in the event of improper use or tampering with the module
or devices supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this
manual are not followed.
WARNING: Before operating, read this document thoroughly and retain it for future reference. Non-respect of these
instructions may reduce performances and safety of the devices and cause danger for people and property. The
products must be installed, operated, serviced and maintained by qualified personnel in compliance with applicable
standards and regulations. Don't open the device, it does not contain replaceable components, the tripping of the
internal fuse (if included) is caused by an internal failure. Don't repair or modify the device, if malfunction or failure
should occur during operation, send unit to the factory for inspection. No responsibility is assumed by SENECA for
any consequences deriving from the use of this material.
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to
electrostatic discharges. Take appropriate measures during any operation.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized
to recycle electrical and electronic waste.
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287
CONTACT INFORMATION
Technical support
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modified or supplemented for technical and/or sales purposes.
MI00573-6-EN
INSTALLATION MANUAL
Z-KEY-2ETH Series
indicates conditions or actions that put the user's safety at risk.
indicates conditions or actions that might damage the instrument or the
DOCUMENTATION
support@seneca.it
INSTALLATION MANUAL
Z-KEY-2ETH
Product information
sales@seneca.it
1/4

Advertisement

loading
Need help?

Need help?

Do you have a question about the Z-KEY-2ETH Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Seneca Z-KEY-2ETH Series

  • Page 1 (if included) is caused by an internal failure. Don’t repair or modify the device, if malfunction or failure should occur during operation, send unit to the factory for inspection. No responsibility is assumed by SENECA for any consequences deriving from the use of this material.
  • Page 2 REFERENCE PRODUCTS Z-KEY-2ETH-0 ModBUS version Z-KEY-2ETH-P with Profinet protocol Z-KEY-2ETH-I with IEC 61850 protocol Z-KEY-2ETH-U with OPC-UA protocol Z-KEY-2ETH-E with Ethernet/IP protocol Z-KEY-2ETH-C ModBUS to Cloud MODULE LAYOUT 17,5 mm Dimensions: 17.5 x 102.5 x 111 mm, Weight: 100 g; Enclosure: PA6, black SIGNALS VIA LED ON FRONT PANEL STATUS LED meaning...
  • Page 3 In devices with Profinet, OPC-UA and IEC61850 protocols, to access the internal webserver it is necessary to switch the device to Webserver mode using the Easy Setup2 or Seneca Device Discovery software, it is also possible to change the operating mode by pressing the PS1 side button following the procedure in the user manual.
  • Page 4 The illustration shows how to complete connections. The RS232 interface is fully settable. Power supply and Modbus interface are available using the Seneca DIN rail bus, via the IDC10 rear connector, or the Z-PC-DINAL2-17.5 accessory. Power Suppl y AC / +...

This manual is also suitable for:

Z-key-2eth-0Z-key-2eth-pZ-key-2eth-iZ-key-2eth-uZ-key-2eth-eZ-key-2eth-c