Seneca Z-KEY-2ETH Installation Manual
  1. Manuals
  2. Brands
  3. Seneca Manuals
  4. Gateway
  5. Z-KEY-2ETH
  6. Installation manual

Seneca Z-KEY-2ETH Installation Manual

Hide thumbs Also See for Z-KEY-2ETH:
1
2
3
4
Table of Contents

Advertisement

Quick Links

Download this manual

PRELIMINARY WARNINGS

The word WARNING preceded by the symbol
The word ATTENTION preceded by the symbol
instrument or the connected equipment. The warranty shall become null and void in the event of improper use or
tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if
the instructions contained in this manual are not followed.
WARNING: The full content of this manual must be read before any operation. The module must only be used by
qualified electricians. Specific documentation is available via QR-CODE shown on page 1.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre
authorized to recycle electrical and electronic waste.
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287
CONTACT INFORMATION
Technical support
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modified or supplemented for technical and/or sales purposes.
MI00573-2-EN
INSTALLATION MANUAL
Z-KEY-2ETH
Z-KEY-2ETH-P
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to
electrostatic discharges. Take appropriate measures during any operation.
DOCUMENTATION
Z-KEY-2ETH
support@seneca.it
INSTALLATION MANUAL
indicates conditions or actions that put the user's safety at risk.
indicates conditions or actions that might damage the
DOCUMENTATION
Z-KEY-2ETH-P
Product information
sales@seneca.it
1/4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Z-KEY-2ETH and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Seneca Z-KEY-2ETH

Summary of Contents for Seneca Z-KEY-2ETH

  • Page 1 The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste. DOCUMENTATION DOCUMENTATION Z-KEY-2ETH Z-KEY-2ETH-P SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287 CONTACT INFORMATION Technical support support@seneca.it Product information sales@seneca.it This document is the property of SENECA srl.
  • Page 2 The device is normally in Profinet mode; in Profinet mode the device can be configured only through the Easy Setup2 software. In order to access the internal webserver it is necessary to put the device in Webserver mode using the Easy Setup2 or Seneca Device Discovery software.
  • Page 3 RESERVED RESERVED must be set to ON To force the device's IP address to the standard value of RESERVED RESERVED SENECA Ethernet products: 192.168.90.101 Reserved RESERVED RESERVED CAUTION Where present, DIP3 and DIP4 must be set to OFF. If set differently, the instrument will not work correctly.
  • Page 4 The illustration shows how to complete connections. The RS232 interface is fully settable. Power supply and Modbus interface are available using the Seneca DIN rail bus, via the IDC10 rear connector, or the Z-PC-DINAL2-17.5 accessory. Power Suppl y AC / +...

This manual is also suitable for:

Z-key-2eth-p

Table of Contents