Supermicro SuperServer SYS-112HA-TN User Manual
  1. Manuals
  2. Brands
  3. Supermicro Manuals
  4. Server
  5. SuperServer SYS-112HA-TN
  6. User manual
Supermicro SuperServer SYS-112HA-TN User Manual

Supermicro SuperServer SYS-112HA-TN User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SuperServer
®
SYS-112HA-TN
USER'S MANUAL
Revision 1.0 MNL-2788

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SuperServer SYS-112HA-TN and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Supermicro SuperServer SYS-112HA-TN

Summary of Contents for Supermicro SuperServer SYS-112HA-TN

  • Page 1 SuperServer ® SYS-112HA-TN USER'S MANUAL Revision 1.0 MNL-2788...
  • Page 2 The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage.

  • Page 3: About This Manual

    Technical Support email addresses can be found at: "Contacting Supermicro" on page 12 If you have any feedback on Supermicro product manuals, contact our writing team at: Techwriterteam@supermicro.com This manual may be periodically updated without notice. Check the Supermicro website for...

  • Page 4: Conventions Used In The Manual

    SuperServer SYS-112HA-TN: Preface Conventions Used in the Manual Special attention should be given to the following symbols for proper installation and to prevent damage done to the components or injury to yourself. Warning! Indicates important information given to prevent equipment/property damage or personal injury.

  • Page 5: Table Of Contents

    SuperServer SYS-112HA-TN: Contents Contents Contacting Supermicro Chapter 1: Introduction 1.1 Overview 1.2 System Features Front View NVMe SSD Drive Indicators Control Panel Rear View 1.3 System Architecture Main Components Motherboard Block Diagram 1.4 Motherboard Quick Reference Motherboard Layout Quick Reference Chapter 2: Server Installation 2.1 Unpacking the System...
  • Page 6 SuperServer SYS-112HA-TN: Contents Installing the Outer Rails onto the Rack 2.4 Installing the Chassis into the Rack Installing the Chassis Removing the Chassis from the Rack Chapter 3: Maintenance and Component Installation 3.1 Removing Power 3.2 Accessing the System Removing the Chassis Cover 3.3 Static-Sensitive Devices...
  • Page 7 SuperServer SYS-112HA-TN: Contents Hot-Swap for NVMe Drives Ejecting a Drive Replacing a Drive 3.8 System Cooling Fans Changing a System Fan Air Shroud Air Shroud for CPU and Memory Installing the Air Shroud 3.9 Expansion Cards Riser Cards Installing Riser Cards...
  • Page 8 SuperServer SYS-112HA-TN: Contents Fail LED (Information LED for OH/FF/PF) LAN1/LAN2 (NIC1/NIC2) LED Storage Drive Activity LED Standby Power LED Root of Trust (RoT) Power LED Standby Power Power Fail LED Indicators 4.4 Input/Output Ports I/O Ports Advanced I/O Module (AIOM) for I/O Support 4.5 Jumper Settings...
  • Page 9 SuperServer SYS-112HA-TN: Contents Hardware Key Configuring Intel VMD Configuring VMD Manually Creating NVMe RAID Configurations Status Indications Hot-Swap Drives Hot-unplug Hot-plug Related Information Links Chapter 7: Troubleshooting and Support 7.1 Online Resources Direct Links for the SYS-112HA-TN System Direct Links for General Support and Information 7.2 Baseboard Management Controller (BMC)
  • Page 10 SuperServer SYS-112HA-TN: Contents 8.4 Event Logs 8.5 BMC 8.6 Security 8.7 Boot 8.8 Save & Exit Appendix A: BIOS Codes BIOS Error POST (Beep) Codes Additional BIOS POST Codes Appendix B: Standardized Warning Statements for AC Systems Warning Definition Installation Instructions...
  • Page 11 SuperServer SYS-112HA-TN: Contents DC Power Supply Power Disconnection Warning Hazardous Voltage or Energy Present on DC Power Terminals Appendix C: System Specifications...

  • Page 12: Contacting Supermicro

    SuperServer SYS-112HA-TN: Contacting Supermicro Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: Marketing@supermicro.com (General Information) Sales-USA@supermicro.com (Sales Inquiries) Government_Sales-USA@supermicro.com (Gov. Sales Inquiries) Support@supermicro.com (Technical Support) RMA@Supermicro.com...

  • Page 13: Chapter 1: Introduction

    SuperServer SYS-112HA-TN: Introduction Chapter 1: Introduction This chapter provides a brief outline of the functions and features of the SYS- 112HA- TN system. It is based on the X14SBH-AP motherboard and the CSE-HS101-R000NFP chassis. 1.1 Overview 1.2 System Features Front View Rear View 1.3 System Architecture...

  • Page 14: Overview

    SuperServer SYS-112HA-TN: Introduction 1.1 Overview ® ® ® The SuperServer SYS-112HA-TN is a X14 Hyper system that supports single Intel Xeon 6900- series processor in a 1U form factor. The system is based on the X14SBH- AP motherboard and the CSE-HS101-R000NFP chassis.
  • Page 15 SuperServer SYS-112HA-TN: Introduction System Overview Motherboard X14SBH-AP Chassis CSE-HS101-R000NFP ® ® Single Intel Xeon 6900-series processor with P-cores (in Socket BR LGA7529) Processor and a thermal design power (TDP) of up to 500 W 12 DIMM slots Memory Max Memory (1DPC): 3 TB 8800 MT/s ECC DDR5 MRDIMM...
  • Page 16 SuperServer SYS-112HA-TN: Introduction Notes: A Quick Reference Guide can be found on the following page of the Supermicro website: https://www.supermicro.com/QuickRefs/superserver/1U/LBL-4037-QRG.pdf The following safety models associated with the SYS-112HA-TN have been certified as compliant with UL or CSA: HS101-R12X14, HS101-R16X14, HS101-R13DX14, or...

  • Page 17: System Features

    SuperServer SYS-112HA-TN: Introduction 1.2 System Features The following views of the system display the main features. Refer to the System Specifications appendix of this manual for additional specifications. Front View ® ® The SYS-112HA-TN is a 1U system containing an Intel...

  • Page 18: Nvme Ssd Drive Indicators

    SuperServer SYS-112HA-TN: Introduction NVMe SSD Drive Indicators Each NVMe SSD module has two LED indicators: an activity indicator and a status indicator. For RAID configurations using a controller, the meaning of the status indicator is described in the table below. For OS RAID or non- RAID configurations, some LED indications are not supported, such as hot spare.

  • Page 19: Control Panel

    SuperServer SYS-112HA-TN: Introduction Control Panel The switches and LEDs located on the control panel of the SYS- 112HA- TN server are described below. Figure 1-2. Control Panel Control Panel Features Feature Description The button switch is a unit identifier button for easy system location in large stack Button/BMC configurations.

  • Page 20: Rear View

    SuperServer SYS-112HA-TN: Introduction Rear View The illustration below shows the features included on the rear of the SYS-112HA-TN system, including the power supply module display status lights. Figure 1-3. Rear View Rear Features Feature Description Two redundant power supplies (PWS1 on the left, PWS2 on the right). See Power Supplies table below for details.
  • Page 21 Indicates that the power supply has a warning condition and continues to Amber, blinking operate. Indicates that the power supply is plugged in and is in an abnormal state. Amber, solid The system might need service. Contact Supermicro technical support. No AC power to modules.

  • Page 22: System Architecture

    SuperServer SYS-112HA-TN: Introduction 1.3 System Architecture This section covers the locations of the system's main components and provides a system block diagram. Main Components Figure 1-4. SYS-112HA-TN Main Component Locations Top Features Feature Description Riser Card Two riser cards (RSC-H-66G5L on the left, RSC-H-6G5L on the right)

  • Page 23: Motherboard Block Diagram

    SuperServer SYS-112HA-TN: Introduction Motherboard Block Diagram Figure 1-5. Motherboard Block Diagram...

  • Page 24: Motherboard Quick Reference

    SuperServer SYS-112HA-TN: Introduction 1.4 Motherboard Quick Reference For details on the X14SBH-AP motherboard layout and other quick reference information, refer to the content below. Motherboard Layout Figure 1-6. X14SBH-AP Motherboard Image...

  • Page 25: Quick Reference

    SuperServer SYS-112HA-TN: Introduction Figure 1-7. X14SBH-AP Motherboard Layout Notes: "Maintenance and Component Installation" on page 39 for detailed information on jumpers, connectors, and LED indicators. "■" indicates the location of pin 1. Components not documented are for internal testing-purposes only.
  • Page 26 Description Onboard Battery FAN1–FAN7 6-pin Fan Headers FAN8–FAN10 4-pin Fan Headers JAIOM1 Supermicro Advanced Input/Output Module (AIOM) PCIe 5.0 x16 Connector JBPNI²C1, 4-pin BMC External I²C Headers for Backplane JBPNI²C2 JFP1 Front Control Panel Header JIO1 Front BMC and Onboard VGA/USB/LAN Module Connector...
  • Page 27 SuperServer SYS-112HA-TN: Introduction Connector Description M.2_MH1–M.2- M.2 Mounting Holes P1_PE0 8–15 MCIO PCIe 5.0 x8 Connector Support P1_PE4 0–7 VPP MCIO PCIe 5.0 x8 Connector Support I²C P1_PE4 8–15 VPP MCIO PCIe 5.0 x8 Connector Support I²C P1_PE5 0-7 VPP MCIO PCIe 5.0 x8 Connector Support...

  • Page 28: Chapter 2: Server Installation

    SuperServer SYS-112HA-TN: Server Installation Chapter 2: Server Installation This chapter provides advice and instructions for mounting your server in a server rack. If your server is not already fully integrated with processors, system memory, etc., refer to "Maintenance and Component Installation" on page 39 for details on installing those specific components.

  • Page 29: Unpacking The System

    SuperServer SYS-112HA-TN: Server Installation 2.1 Unpacking the System Inspect the box the server was shipped in and note if it was damaged in any way. If any equipment appears damaged, file a damage claim with the carrier who delivered it.

  • Page 30: Preparing For Setup

    SuperServer SYS-112HA-TN: Server Installation 2.2 Preparing for Setup The box in which the SYS- 112HA- TN server was shipped should include the rackmount hardware needed to install it into the rack. Read this section in its entirety before you begin the installation.

  • Page 31: Rack Mounting Considerations

    SuperServer SYS-112HA-TN: Server Installation Use a regulating uninterruptible power supply (UPS) to protect the server from power surges and voltage spikes and to keep your system operating in case of a power failure. Allow any drives and power supply modules to cool before touching them.

  • Page 32: Circuit Overloading

    SuperServer SYS-112HA-TN: Server Installation Circuit Overloading Consideration should be given to the connection of the equipment to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

  • Page 33: Installing The Rails

    SuperServer SYS-112HA-TN: Server Installation 2.3 Installing the Rails This section provides information on installing the CSE-HS101-R000NFP chassis into a rack unit with the rails provided. There are a variety of rack units on the market, which may mean that the assembly procedure will differ slightly from the instructions provided. You should also refer to the installation instructions that came with the rack unit you are using.

  • Page 34: Installing The Inner Rails Onto The Chassis

    SuperServer SYS-112HA-TN: Server Installation 2. Press down the locking lever on the inside of the inner rail to release the inner rail. Continue to pull the inner rail out of the middle rail. Figure 2-2. Extending the Rails and Releasing the Inner Rail...

  • Page 35: Installing The Outer Rails Onto The Rack

    SuperServer SYS-112HA-TN: Server Installation Figure 2-3. Installing the Inner Rails Installing the Outer Rails onto the Rack After the inner rails are installed onto the CSE-HS101-R000NFP chassis, begin installing the outer rails onto the rack. 1. Confirm that the left and right outer rails have been correctly identified.

  • Page 36: Installing The Chassis Into The Rack

    SuperServer SYS-112HA-TN: Server Installation Figure 2-4. Installing the Outer Rails Important: This figure is for illustrative purposes only. Always install servers to the bottom of a rack first. 2.4 Installing the Chassis into the Rack After the rails are installed on the CSE-HS101-R000NFP chassis and on the rack, the server can be installed in the rack.

  • Page 37: Removing The Chassis From The Rack

    SuperServer SYS-112HA-TN: Server Installation Figure 2-5. Installing the Chassis into the Rack Important: This figure is for illustrative purposes only. Always install servers to the bottom of a rack first. Removing the Chassis from the Rack Important: Mounting or removing the system from the rack requires at least three people to support the chassis during installation.
  • Page 38 SuperServer SYS-112HA-TN: Server Installation Figure 2-6. Removing the Chassis from the Rack Important: This figure is for illustrative purposes only. Always install servers to the bottom of a rack first.

  • Page 39: Chapter 3: Maintenance And Component Installation

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Chapter 3: Maintenance and Component Installation This chapter provides instructions on installing and replacing main system components for the SYS-112HA-TN server. To prevent compatibility issues, only use components that match the specifications and/or part numbers given.
  • Page 40 SuperServer SYS-112HA-TN: Maintenance and Component Installation Battery Installation 3.7 Storage Drives Removing Drive Carriers from the Chassis Installing a 2.5" Drive Hot-Swap for NVMe Drives 3.8 System Cooling Fans Air Shroud 3.9 Expansion Cards Riser Cards AIOM Cards 3.10 Power Supply Replacing the Power Supply 3.11 Cable Routing Diagrams...

  • Page 41: Removing Power

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.1 Removing Power Use the following procedure to ensure that power has been removed from the SYS-112HA-TN server. This step is necessary when removing or installing non-hot-swap components or when replacing a non-redundant power supply.

  • Page 42: Accessing The System

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.2 Accessing the System The SYS-112HA-TN features a removable top cover for access to the internal components. When performing service on components inside the system, remove the system from the rack and place it on a work bench or desk. Do not service with the system extended from the rack.

  • Page 43: Static-Sensitive Devices

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.3 Static-Sensitive Devices Electrostatic Discharge (ESD) can damage electronic components. To avoid damaging your motherboard, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD.

  • Page 44: Processor And Heatsink Installation

    (gold contacts). Improper installation or socket misalignment can cause serious damage to the processor or processor socket. When buying a processor separately, use only a Supermicro certified heatsink. Refer to the Supermicro website for the most recent processor support.

  • Page 45: Socket Br Lga7529 Processors

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Socket BR LGA7529 Processors Processor Top View Figure 3-2. Processor Overview of the Processor Carrier This section displays the X14SBH-AP motherboard processor carrier. Figure 3-3. Carrier BR1A...
  • Page 46 SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-4. Carrier Top View Figure 3-5. Carrier Bottom View...

  • Page 47: Overview Of The Processor Socket

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Overview of the Processor Socket The processor socket is protected by a plastic protective cover. Figure 3-6. Plastic Protective Cover and Processor Socket Overview of the Processor Heatsink Module The Processor Heatsink Module (PHM) contains a heatsink, a processor carrier, and the processor.

  • Page 48: Installing The Processor

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-8. Carrier Figure 3-9. Processor Installing the Processor To install a processor into the processor carrier, follow the steps below: 1. Ensure the lever on the processor carrier is pressed down and held by a latch on the processor carrier as shown below.
  • Page 49 SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-11. Processor Figure 3-12. Carrier 3. While ensuring that the pin 1 triangles point towards the same direction, flip over the processor and processor carrier. Use the latches on the processor carrier to secure the processor onto the processor carrier.

  • Page 50: Assembling The Processor Heatsink Module

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-14. Processor and BR1A Keys and Latches Figure 3-15. Completed Processor Carrier Installation Assembling the Processor Heatsink Module After installing the processor into the carrier, mount it onto the heatsink to create the processor heatsink module (PHM): 1.
  • Page 51 SuperServer SYS-112HA-TN: Maintenance and Component Installation 1. Locate the four threaded fasteners (marked a, b, c, and d) on the processor socket. Figure 3-16. Threaded Fasteners 2. Locate the four PEEK nuts (marked A, B, C, and D) and four rotating wires (marked 1, 2, 3, and 4) on the heatsink.

  • Page 52: Preparing The Processor Socket For Installation

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Preparing the Processor Socket for Installation This motherboard comes with a plastic protective cover installed on the processor socket. Remove it from the socket to install the Processor Heatsink Module (PHM). Gently pull up one corner of the plastic protective cover to remove it.
  • Page 53 SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-21. Aligning the Heatsink with the Socket 3. Press all four rotating wires inwards and make sure that the heatsink is securely latched into the processor socket. Figure 3-22. Latching the PHM 4. With a T30 bit torque driver set to a force of 8.0 in-lbf (0.904 N-m), gradually tighten the four screws to ensure even pressure.

  • Page 54: Removing The Processor Heatsink Module

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-23. Installing the PHM with a Torque Driver 6. With a T30 bit torque driver set to a force of 2.6 in-lbf (0.294 N-m), tighten the remote screws by the following order: 1-2.
  • Page 55 SuperServer SYS-112HA-TN: Maintenance and Component Installation 2. Use a screwdriver to loosen the four screws. You can start with any screw, but make sure to loosen the screws in a diagonal pattern. Figure 3-26. Loosening the Screws 3. Press the four rotating wires outwards to unlatch the PHM from the socket.
  • Page 56 SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-29. Carrier with Heatsink 6. To remove the processor, move the lever to its unlocked position and gently remove the processor. Figure 3-30. Removing the Processor...

  • Page 57: Memory Support And Installation

    3.5 Memory Support and Installation Important: Exercise extreme care when installing or removing memory modules to prevent any damage. Note: Check the Supermicro website for recommended memory modules. Memory Support The X14SBH- AP motherboard supports up to 3 TB of 3DS RDIMM/MRDIMM DDR5 ECC memory with speeds of up to 8800 MT/s in 12 memory slots.

  • Page 58: General Guidelines For Optimizing Memory Performance

    SuperServer SYS-112HA-TN: Maintenance and Component Installation ® ® Intel Xeon 6900-Series Processors with P-Cores DDR5 Memory Population Table (1 Processor and 12 DIMMs Installed, 1DPC) 1 Processor and 1 P1-DIMMA1 DIMM 1 Processor and 8 P1-DIMMC1/P1-DIMMD1/P1-DIMME1/P1-DIMMF1/P1-DIMMI1/P1- DIMMs DIMMJ1/P1-DIMMK1/P1-DIMML1 1 Processor and 8...
  • Page 59 SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-31. Unlocking the DIMM Slot 3. Align the key of the DIMM with the receptive point on the memory slot. Figure 3-32. Aligning the DIMM Slot with the Receptive Point 4. Align the notches on both ends of the module against the receptive points on the ends of...
  • Page 60 SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-33. Aligning the Notches 5. Press both ends of the module straight down into the slot until the module snaps into place. 6. Press the release tabs to the lock positions to secure the DIMM into the slot.

  • Page 61: Dimm Removal

    SuperServer SYS-112HA-TN: Maintenance and Component Installation DIMM Removal Important: Do not use excessive force when pressing the release tabs on the ends of the DIMM socket to avoid causing any damage to the memory module or the DIMM socket. Handle memory modules with care. Carefully follow all the instructions given in "Static-...

  • Page 62: Motherboard Battery Removal And Installation

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.6 Motherboard Battery Removal and Installation Battery Removal To remove the onboard battery, follow the steps below: 1. Power off your system and unplug your power cable. 2. Locate the onboard battery as shown below.

  • Page 63: Storage Drives

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.7 Storage Drives The system supports up to eight front hot- swap 2.5" NVMe/SAS/SATA drive bays and (optional) four hot-swap 2.5" SAS/SATA drive bays. Note: NVMe/SAS/SATA support may require additional storage controller and/or cables.

  • Page 64: Installing A 2.5" Drive

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-39. Removing a Drive Carrier Installing a 2.5" Drive 1. Insert a drive into the carrier with the PCB side facing down and the connector end toward the rear of the carrier. Place the drive in the carrier so that the screw holes line 2.

  • Page 65: Hot-Swap For Nvme Drives

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-40. Installing a 2.5" Drive into a Carrier Hot-Swap for NVMe Drives Supermicro servers support NVMe surprise hot-swap. For even better data security, NVMe orderly hot-swap is recommended. NVMe drives can be ejected and replaced remotely using BMC.

  • Page 66: Replacing A Drive

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-41. BMC Screenshot Replacing a Drive 1. Insert the replacement drive. 2. BMC > System > Storage Monitor > Physical View 3. Select Device, Group, and slot and click Insert. The drive Status LED indicator flashes...

  • Page 67: System Cooling

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.8 System Cooling Refer to the following sections for information about the cooling capabilities of the SYS-112HA- TN server. Fans Up to eight heavy- duty fans provide cooling for the SYS- 112HA- TN server. They can be replaced without powering down the system.

  • Page 68: Air Shroud

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Air Shroud Air shrouds concentrate airflow to maximize fan efficiency. The SYS-112HA-TN includes one air shroud for the CPU. Air Shroud for CPU and Memory The air shroud cools the CPU and DIMM slots controlled by the CPU (see figure below).

  • Page 69: Expansion Cards

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.9 Expansion Cards Refer to the following sections for information on the expansion cards supported by the SYS- 112HA-TN server. Riser Cards The SYS-112HA-TN includes two riser cards to support the use of expansion (add-on) cards.
  • Page 70 SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-45. Installing Left Expansion Card (RSC-H-6G5L)

  • Page 71: Aiom Cards

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-46. Installing Right Expansion Card (RSC-H-66G5L) AIOM Cards The system supports one AIOM/OCP NIC 3.0 network port card. AIOM Configurations Slot Mechanical Electrical Slot Power Small form factor, OCP 3.0 PCIe 5.0 x16 (CPU1)

  • Page 72: Installing Aiom Cards

    SuperServer SYS-112HA-TN: Maintenance and Component Installation Note: AIOM cards exceeding the 15 W slot class may require restricted conditions to meet thermal specifications of the AIOM card. Contact your Supermicro account representative for more information. Figure 3-47. AIOM Chassis Slot Installing AIOM Cards 1.

  • Page 73: Power Supply

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.10 Power Supply The SYS- 112HA- TN server features two 1200 W/1600 W/2000 W AC redundant Titanium Level power supplies or two 1300 W DC redundant power supplies. Each power supply can be changed without powering down the system. New units can be ordered directly from Supermicro or authorized distributors.

  • Page 74: Cable Routing Diagrams

    SuperServer SYS-112HA-TN: Maintenance and Component Installation 3.11 Cable Routing Diagrams The below diagrams indicate the cable routing for the storage, PCIe, IO, and power cables. When disconnecting cables to add or replace components, refer to the diagrams so you can reroute them in the same manner.
  • Page 75 SuperServer SYS-112HA-TN: Maintenance and Component Installation NVMe Drive Cable Routing Figure 3-50. Eight NVMe Cable Routing...
  • Page 76 SuperServer SYS-112HA-TN: Maintenance and Component Installation Eight NVMe Connector on Drive Backplane/Riser and Port SMC Cable P/N Board/Card CN1 (BPN-NVME5-HS119N- CBL-MCIO- P1_NVME0/1 S8L) 1255M5REL CN2 (BPN-NVME5-HS119N- CBL-MCIO- P1_NVME2/3 S8L) 1255M5REL CN3 (BPN-NVME5-HS119N- P1_NVME4/5 S8L) CBL-MCIO- 1464M5FRFB-J CN4 (BPN-NVME5-HS119N- P1_NVME6/7 S8L)
  • Page 77 SuperServer SYS-112HA-TN: Maintenance and Component Installation Storage AOC Drive Cable Routing Figure 3-51. 12 SAS Cable Routing 12 SAS Connector on Drive Backplane/Riser and Port SMC Cable P/N Board/Card JSM1/JSM2 (BPN-NVME5- CBL-SAST-1273LP- SAS AOC CN1 HS119N-S8L) CBL-SAST-1262LP- SAS AOC CN2...
  • Page 78 SuperServer SYS-112HA-TN: Maintenance and Component Installation Figure 3-52. Eight NVMe Cable Routing Eight SAS Connector on Drive Backplane/Riser and Port SMC Cable P/N Board/Card JSM1/JSM2 (BPN-NVME5- CBL-SAST-1273LP- SAS AOC CN1 HS119N-S8L)

  • Page 79: Chapter 4: Motherboard Connections, Jumpers, And Leds

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs Chapter 4: Motherboard Connections, Jumpers, and LEDs This section describes the connections on the motherboard and provides pinout definitions. Note that depending on how the system is configured, not all connections are required. The LEDs on the motherboard are also described here.
  • Page 80 SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs Power Fail LED Indicators 4.4 Input/Output Ports I/O Ports Advanced I/O Module (AIOM) for I/O Support 4.5 Jumper Settings CMOS Clear Onboard TPM Enable/Disable UID LED and System_Reset Button Select Jumper 4.6 LED Indicators...

  • Page 81: Power Supply And Power Connections

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs 4.1 Power Supply and Power Connections For information about the power supply and power connections of the SYS-112HA-TN server, refer to the following content. Power Connectors JPW1–JPW10 are the 8-pin power connectors located on the X14SBH-AP motherboard. In addition, there are two power supply units for system use located at PSU1 and PSU2.

  • Page 82: Headers And Connections

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs 4.2 Headers and Connections For information about the headers of the SYS-112HA-TN server, refer to the following content. BMC LAN/USB/VGA Connector A low-profile SlimSAS I/O x8 connector, located at JIO1 on the X14SBH-AP motherboard, provides dedicated BMC LAN/USB/VGA support for access.

  • Page 83: Fan Headers

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs Fan Headers There are seven 6-pin fan headers (FAN1–FAN7) and three 4-pin fan headers (FAN8–FAN10) on the X14SBH-AP motherboard. All the 4-pin fan headers are backwards compatible with the traditional 3- pin fans. However, fan speed control is available for all fans except FAN9 by Thermal Management via the IPMI 2.0 interface.

  • Page 84: Nvme I²C Headers

    NVMe I²C Headers Connectors JNVI²C1 and JNVI²C2 on the X14SBH-AP motherboard are the NVMe hot-swap management headers for the Supermicro NVMe backplane. Connect the I²C cable to these connectors. For a detailed diagram of the X14SBH-AP motherboard, see the layout under "Motherboard...

  • Page 85: Universal Serial Bus (Usb) Header

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs Universal Serial Bus (USB) Header There is one USB 3.2 Gen 1 header located at USB2/3 on the X14SBH-AP motherboard. For a detailed diagram of the X14SBH-AP motherboard, see the layout under "Motherboard Quick Reference"...

  • Page 86: Front Control Panel

    JFP1, contains header pins for various buttons and LED indicators with I²C support for front access. This head is designed specifically for use with the Supermicro chassis. For a detailed diagram of the X14SBH-AP motherboard, see the layout under "Motherboard...

  • Page 87: Uid Led

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs For a detailed diagram of the X14SBH-AP motherboard, see the layout under "Motherboard Quick Reference" on page Power Button BMC/BIOS Status LED Indicator Status Event Green: Solid on System power on BMC/BIOS blinking green at 4 Hz...

  • Page 88: Lan1/Lan2 (Nic1/Nic2) Led

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs Fail LED (Information LED) (OH/Fan Fail/PWR Fail) LED States Status Description Red Info LED blinking (10 Hz) and MB UID CPLD: recovery and/or update in progress. LED blue blinking (10 Hz) LAN1/LAN2 (NIC1/NIC2) LED The Network Interface Controller (NIC) LED connection for LAN Port 1 is located on pin 6 of JFP1 on the X14SBH-AP motherboard, and LAN Port 2 is on pin 5.

  • Page 89: Root Of Trust (Rot) Power Led

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs Root of Trust (RoT) Power LED The Power LED for the Root of Trust (RoT) connection is located on pin 9 of JFP1 on the X14SBH-AP motherboard. If this LED is on, power for the RoT chip is on.

  • Page 90: Input/Output Ports

    PSU1 Advanced I/O Module (AIOM) for I/O Support A Supermicro proprietary Advanced I/O Module (AIOM) connector used for an add-on module is located on the X14SBH- AP motherboard. This AIOM connector provides input/output connections on the I/O face of your system.

  • Page 91: Jumper Settings

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs 4.5 Jumper Settings To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board.

  • Page 92: Onboard Tpm Enable/Disable

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs 4. Short the CMOS pads, JBT1, with a metal object such as a small screwdriver for at least four seconds. Note: Clearing CMOS will also clear all passwords. 5. Remove the screwdriver (or shorting device).

  • Page 93: Led Indicators

    SuperServer SYS-112HA-TN: Motherboard Connections, Jumpers, and LEDs 4.6 LED Indicators For information about the LED indicators on the SYS-112HA-TN server, refer to the following content. BMC Heartbeat LED A BMC Heartbeat LED is located at LED3 on the X14SBH-AP motherboard. When this LED is blinking, the BMC is functioning normally.

  • Page 94: Chapter 5: Software

    SuperServer SYS-112HA-TN: Software Chapter 5: Software After the SYS-112HA-TN server has been installed, you can install the Operating System (OS), configure RAID settings, and install the drivers. 5.1 Microsoft Windows OS Installation Installing the OS 5.2 Driver Installation 5.3 BMC...

  • Page 95: Microsoft Windows Os Installation

    USB flash or media drive, or the BMC KVM console. 2. Retrieve the proper drivers. Go to the Supermicro web page for your motherboard and click on "Download the Latest Drivers and Utilities," select the proper driver, and copy it to a USB flash drive.
  • Page 96 SuperServer SYS-112HA-TN: Software Figure 5-2. Loading the Driver Link To load the driver, browse the USB flash drive for the proper driver files. 5. Once all devices are specified, continue with the installation. 6. After the Windows OS installation has completed, the system will automatically reboot...

  • Page 97: Driver Installation

    SuperServer SYS-112HA-TN: Software 5.2 Driver Installation The Supermicro website contains drivers and utilities for your system at the following page: https://www.supermicro.com/wdl. Some of these drivers and utilities must be installed, such as the chipset driver. After accessing the website, go into the CDR_Images (in the parent directory of the above link) and locate the ISO file for your motherboard.
  • Page 98 SuperServer SYS-112HA-TN: Software Figure 5-3. Driver & Tools Installation Screen...

  • Page 99: Bmc

    When logging in to the BMC for the first time, use the unique password provided by Supermicro to log in. You can change the unique password to a user name and password of your choice for subsequent logins.

  • Page 100: Chapter 6: Optional Components

    SuperServer SYS-112HA-TN: Optional Components Chapter 6: Optional Components This chapter describes alternate configurations and optional system components for the SYS- 112HA-TN server. 6.1 TPM Security Module 6.2 HBA Card 6.3 RAID Cards 6.4 Cable Management Arm Installing the Cable Management Arm Removing the Cable Management Arm 6.5 Intel Virtual RAID on CPU (VROC)

  • Page 101: Tpm Security Module

    SuperServer SYS-112HA-TN: Optional Components 6.1 TPM Security Module SPI capable TPM 2.0 with Infineon 9670 controller, vertical form factor. The JTPM1 header is used to connect a Trusted Platform Module (TPM). A TPM is a security device that supports encryption and authentication in hard drives. It enables the X14SBH-AP motherboard to deny access if the TPM associated with the hard drive is not installed in the SYS-112HA-TN server.

  • Page 102: Hba Card

    This is a 12 Gb/s, multi-port SAS PCIe Gen 4.0 internal Host Bus Adapter (HBA) card. The Supermicro HBA AOC- S3816L- L16iT features 16 internal SAS connectors, while the AOC- S3808L- L8iT features eight internal SAS connectors. Both are designed for high- performance storage connectivity.

  • Page 103: Raid Cards

    SuperServer SYS-112HA-TN: Optional Components 6.3 RAID Cards These are Super Micro Computer, Inc. 12 Gb/s, multi-port PCIe Gen 4.0 RAID adapter cards. The low-profile AOC-S3908L-H8iR RAID card features eight internal SAS connectors and the AOC- S3916L- H16iR features 16 internal SAS connectors. Both offer high- performance storage connectivity.

  • Page 104: Cable Management Arm

    SuperServer SYS-112HA-TN: Optional Components 6.4 Cable Management Arm The SYS-112HA-TN server supports a cable management arm (CMA), which keeps the rear cables organized and clear of the rail mechanisms when the system is extended out the front of the rack for maintenance.

  • Page 105: Removing The Cable Management Arm

    SuperServer SYS-112HA-TN: Optional Components Figure 6-2. Installing the Connectors 3. Slide CMA connector #3 forward onto the two posts on the rear of the left middle rail. It snaps into place. 4. For CMA connector #4, align the metal tabs with the slots on the rear of the left outer rail and push it forward.

  • Page 106: Intel Virtual Raid On Cpu (Vroc)

    SuperServer SYS-112HA-TN: Optional Components 6.5 Intel Virtual RAID on CPU (VROC) ® Intel Virtual RAID on CPU (Intel VROC) is an enterprise RAID solution for NVMe SSDs directly attached to Intel Xeon Scalable processors. Intel Volume Management Device (VMD) is an integrated controller inside the CPU PCIe root complex.

  • Page 107: Hardware Key

    Hardware Key The Intel VROC hardware key is a license key that detects the Intel VROC SKU and activates the function accordingly. The key must be plugged into the Supermicro motherboard (connector JRK1). The key options are: ® Intel...

  • Page 108: Configuring Vmd Manually

    SuperServer SYS-112HA-TN: Optional Components Auto: Enables VMD for all NVMe ports if VROC Key is installed. VMD: Enables VMD for all NVMe ports despite the lack of the VROC Key. Manual: Allows the user to select specific NVMe ports on which to enable VMD.
  • Page 109 SuperServer SYS-112HA-TN: Optional Components Figure 6-4. BIOS, Selecting NVMe Mode 4. VMD must only be enabled on NVMe port resources. If VMD is enabled on other PCIe ports, the functionality of those ports will be impacted. Select Intel VMD Technology and enable VMD for devices under the respective PCIe ports.
  • Page 110 SuperServer SYS-112HA-TN: Optional Components Figure 6-6. BIOS, Enabling VMD on IIO Domain (Example) 6. Enable the NVMe port resource for the NVMe drives that will be used in a RAID configuration. Figure 6-7. BIOS, Enabling Intel VMD for NVMe1 (Example) 7.

  • Page 111: Creating Nvme Raid Configurations

    SuperServer SYS-112HA-TN: Optional Components Creating NVMe RAID Configurations 1. Open Advanced > Intel(R) Virtual RAID on CPU > All Intel VMD Controllers > Create RAID Volume. Figure 6-8. Created Volume without enabling RAID spanned over VMD controller...

  • Page 112: Status Indications

    SuperServer SYS-112HA-TN: Optional Components Figure 6-9. Created Volume with enabling RAID spanned over VMD controller 2. Set Name. 3. Set RAID Level. 4. If cross-controller RAID is required, select Enable RAID spanned over VMD Controller. 5. Select specific disks for RAID with an [X].

  • Page 113: Hot-Swap Drives

    SuperServer SYS-112HA-TN: Optional Components Drive Carrier Status LED Indicator Status State (red) Normal function Locating 4 Hz blinking Fault Solid on Rebuilding 1 Hz blinking IBPI SFF 8489 Defined Status LED States Hot-Swap Drives Intel VMD enables hot- plug and hot- unplug for NVMe SSDs, whether from Intel or other manufacturers.

  • Page 114: Chapter 7: Troubleshooting And Support

    SuperServer SYS-112HA-TN: Troubleshooting and Support Chapter 7: Troubleshooting and Support The following content contains information on common issues and how to resolve them. 7.1 Online Resources 7.2 Baseboard Management Controller (BMC) 7.3 Troubleshooting Procedures Before Power On No Power No Video...

  • Page 115: Online Resources

    SuperServer SYS-112HA-TN: Troubleshooting and Support 7.1 Online Resources A great deal of information is available on the Supermicro website. From the top menu of the Supermicro home page at https://www.supermicro.com: Specifications for servers and other hardware are available by clicking Products.

  • Page 116: Baseboard Management Controller (Bmc)

    SuperServer SYS-112HA-TN: Troubleshooting and Support 7.2 Baseboard Management Controller (BMC) The SYS-112HA-TN server supports the Baseboard Management Controller (BMC). BMC is used to provide remote access, monitoring, and management. There are several BIOS settings that are related to BMC. For general documentation and information on BMC, visit our website at the following page: https://www.supermicro.com/en/solutions/management-software/bmc-resources...

  • Page 117: Troubleshooting Procedures

    SuperServer SYS-112HA-TN: Troubleshooting and Support 7.3 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the "Technical Support Procedures" on page 123 section in this chapter. Always disconnect the AC power cord before adding, changing or installing any non hot-swap hardware components.

  • Page 118: Memory Errors

    BIOS installed in your system. 2. Memory support: Make sure that the memory modules are supported. Refer to the product page on our website at https://www.supermicro.com. Test the modules using memtest86 or a similar utility. Note: Click on the "Tested Memory List" link on the motherboard's product page to...
  • Page 119 SuperServer SYS-112HA-TN: Troubleshooting and Support 3. Storage Drive support: Make sure that all storage drives work properly. Replace the failed storage drives with good ones. 4. System cooling: Check the system cooling to make sure that all heatsink fans and processor/system fans, etc., work properly.

  • Page 120: Cmos Clear

    SuperServer SYS-112HA-TN: Troubleshooting and Support 7.4 CMOS Clear JBT1 on the X14SBH- AP motherboard is used to clear CMOS, which will also clear any passwords. For information on clearing CMOS, refer to "CMOS Clear" on page 91 earlier in this...

  • Page 121: Motherboard Battery

    SuperServer SYS-112HA-TN: Troubleshooting and Support 7.5 Motherboard Battery For information on removing, disposing of, and replacing the motherboard battery of your system, refer to "Motherboard Battery Removal and Installation" on page...

  • Page 122: Where To Get Replacement Components

    7.6 Where to Get Replacement Components If you need replacement parts for your SYS-112HA-TN server, to ensure the highest level of professional service and technical support, purchase exclusively from our Supermicro Authorized Distributors/System Integrators/Resellers. A list can be found on the Supermicro website: https://www.supermicro.com...

  • Page 123: Technical Support Procedures

    Before contacting Technical Support, take the following steps. Also, note that as a motherboard manufacturer, Supermicro also sells motherboards through its channels, so it is best to first check with your distributor or reseller for troubleshooting services. They should know of any possible problems with the specific system configuration that was sold to you.
  • Page 124 SuperServer SYS-112HA-TN: Troubleshooting and Support This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alternation, misuse, abuse or improper maintenance of products. During the warranty period, contact your distributor first for any product problems.

  • Page 125: Feedback

    SuperServer SYS-112HA-TN: Troubleshooting and Support 7.8 Feedback Supermicro values your feedback as we strive to improve our customer experience in all facets of our business. Email us at Techwriterteam@supermicro.com to provide feedback on our manuals.

  • Page 126: Chapter 8: Uefi Bios

    SuperServer SYS-112HA-TN: UEFI BIOS Chapter 8: UEFI BIOS The following content contains information on BIOS configuration with the SYS-112HA-TN server. 8.1 Introduction 8.2 Main Setup 8.3 Advanced Setup Configurations 8.4 Event Logs 8.5 BMC 8.6 Security 8.7 Boot 8.8 Save & Exit...

  • Page 127: Introduction

    SuperServer SYS-112HA-TN: UEFI BIOS 8.1 Introduction This chapter describes the AMIBIOS™ Setup utility for the motherboard. The BIOS is stored on a chip and can be easily upgraded using the UEFI script (flash.nsh), the BMC WebUI, or the SuperServer Automation Assistant (SAA) utility.
  • Page 128 SuperServer SYS-112HA-TN: UEFI BIOS The Main BIOS screen has two main frames. The left frame displays all the options that can be configured. “Grayed- out” options cannot be configured. The right frame displays the key legend. Above the key legend is an area reserved for a text message. When a BIOS submenu or item is selected in the left frame, it is highlighted in white.

  • Page 129: Main Setup

    SuperServer SYS-112HA-TN: UEFI BIOS 8.2 Main Setup The Main setup screen appears when the AMI BIOS Setup utility is first entered. To return to the Main setup screen, select the Main tab at the top of the screen. The Main BIOS setup screen is shown below.
  • Page 130 SuperServer SYS-112HA-TN: UEFI BIOS Build Date This feature displays the date when the version of the BIOS ROM used in the system was built. CPLD Version This feature displays the version of the Complex-Programmable Logical Device (CPLD) used in the system.

  • Page 131: Advanced Setup Configurations

    SuperServer SYS-112HA-TN: UEFI BIOS 8.3 Advanced Setup Configurations Use the arrow keys to select the Advanced submenu and press <Enter> to access the submenu items. Important: Use caution when changing the Advanced settings. An incorrect value, an improper DRAM frequency, or a wrong BIOS timing setting may cause the system to malfunction.

  • Page 132: Event Logs

    SuperServer SYS-112HA-TN: UEFI BIOS 8.4 Event Logs Use this menu to configure Event Logs settings. Note: After making any changes in this section, please be sure to reboot the system for the changes to take effect. Figure 8-3. Event Logs Screen ►Change SMBIOS Event Log Settings...
  • Page 133 SuperServer SYS-112HA-TN: UEFI BIOS Erasing Settings Erase Event Log (Available when "SMBIOS Event Log" is set to Enabled) Select No to keep the event log without erasing it upon next system bootup. Select (Yes, Next reset) to erase the event log upon next system reboot. The options are No, (Yes, Next reset), and (Yes, Every reset).

  • Page 134: Bmc

    SuperServer SYS-112HA-TN: UEFI BIOS 8.5 BMC Use this menu to configure Baseboard Management Console (BMC) settings. Figure 8-4. BMC Screen BMC Firmware Revision This feature indicates the BMC firmware revision used in this system. BMC STATUS This feature indicates the status of the BMC firmware installed in this system.

  • Page 135: Security

    SuperServer SYS-112HA-TN: UEFI BIOS 8.6 Security Use this menu to configure the following security settings for the system. Figure 8-5. Security Screen Disable Block Sid and Freeze Lock (Available when your storage devices support TCG) Select Enabled to allow SID authentication to be performed in TCG storage devices. The options are Disabled and Enabled.
  • Page 136 SuperServer SYS-112HA-TN: UEFI BIOS Administrator Password This feature indicates if an administrator password has been installed. Use this feature to set the administrator password, which is required to enter the BIOS Setup utility. The length of the password can be between three and 20 characters long.

  • Page 137: Boot

    SuperServer SYS-112HA-TN: UEFI BIOS 8.7 Boot Use this menu to configure Boot settings. Figure 8-6. Boot Screen FIXED BOOT ORDER Priorities Use this feature to prioritize the order of a bootable device from which the system will boot. Press <Enter> on each item sequentially to select the device.
  • Page 138 SuperServer SYS-112HA-TN: UEFI BIOS Path for boot option Use this feature to enter the path for the new boot option in the format fsx:\path\filename.efi. Boot option File Path Use this feature to specify the file path for the new boot option.

  • Page 139: Save & Exit

    SuperServer SYS-112HA-TN: UEFI BIOS 8.8 Save & Exit Select Save & Exit from the BIOS Setup screen to configure the settings below. Figure 8-7. Save & Exit Screen Save Options Discard Changes and Exit Use this feature to exit from the BIOS Setup utility without making any permanent changes to the system configuration and reboot the computer.
  • Page 140 SuperServer SYS-112HA-TN: UEFI BIOS Discard Changes Select this feature and press <Enter> to discard all changes made and return to the BIOS Setup utility. Default Options Restore Optimized Defaults Select this feature and press <Enter> to load manufacturer optimized default settings, which are intended for maximum system performance but not for maximum stability.

  • Page 141: Appendix A: Bios Codes

    SuperServer SYS-112HA-TN: BIOS Codes Appendix A: BIOS Codes For information about BIOS codes for the SYS-112HA-TN server, refer to the following content. BIOS Error POST (Beep) Codes During the Power-On Self-Test (POST) routines, which are performed each time the system is powered on, errors may occur.

  • Page 142: Appendix B: Standardized Warning Statements For Ac Systems

    Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components. Read this section in its entirety before installing or configuring components in the Supermicro SYS-112HA-TN server. These warnings may also be found on our website at the following page: https://www.supermicro.com/about/policies/safety_information.cfm...
  • Page 143 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 此警 告符 號代 表危 險 。 您 正 處 於 可 能 身 體 可 能 會 受 損 傷 的 工 作 環 境 中 。 在 您 使 用 任 何 設 備 之 前 ， 請 注 意 觸 電 的...

  • Page 144: Installation Instructions

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ‫אזהרה‬ ‫הצהרות‬ ‫תקנון‬ ‫חבלה‬ ‫מפני‬ ‫המשתמש‬ ‫את‬ ‫להזהיר‬ ‫מנת‬ ‫על‬ ,‫התעשייה‬ ‫תקני‬ ‫פי‬ ‫על‬ ‫אזהרות‬ ‫הן‬ ‫הבאות‬ ‫הצהרות‬ ‫תמיכה‬ ‫מחלקת‬ ‫עם‬ ‫קשר‬ ‫ליצור‬ ‫יש‬ ,‫כלשהי‬ ‫בבעיה‬ ‫היתקלות‬ ‫או‬ ‫שאלות‬ ‫ויש‬ ‫במידה‬ .‫אפשרית‬...

  • Page 145: Circuit Breaker

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 設置 手順 書 システムを電源 に接続する前 に、 設置 手順 書をお読 み下さ い。 警告 将此 系统 连接 电源 前,请先 阅读 安装 说明 。 警告 將系 統與 電源 連接 前， 請先 閱讀 安裝 說明 。...
  • Page 146 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems サーキッ ト ・ ブレーカ ー こ の製品 は、 短 絡( 過 電流 ) 保 護装 置がある建 物での設置 を前提 と し ています。 保護 装置 の定格 が250 V、 20 Aを超えないこ と を確認 下さ い。...

  • Page 147: Power Disconnection Warning

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 경고! 이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장 치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다. Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie.

  • Page 148: Equipment Installation

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema.
  • Page 149 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 機器 の設置 トレーニングを受 け認 定 さ れた人 だけがこ の装 置 の設 置 、 交 換 、 またはサービスを許 可 さ れていま す。 警告 只有 经过 培训 且具 有资 格的 人员 才能 进行 此设 备的安 装 、 更换 和维 修 。...

  • Page 150: Restricted Area

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Waarschuwing Alleen geautoriseerd personeel en gekwalificeerd onderhoudspersoneel mag deze apparatuur installeren, vervangen of onderhouden. Restricted Area Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

  • Page 151: Battery Handling

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Attention Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout autre moyen de sécurité.
  • Page 152 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 警告 如 果 更 换 的 电 池 类型 不 正 确 。 请 只 使 用 同 类电 池 或 制 造 商 推 荐 的 功 能 相 当 的 电 池 更 换 原...

  • Page 153: Redundant Power Supplies

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 경고! 배터리를 잘못된 종류로 교체하면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사 에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터 리를 처리하여 주십시오. WAARSCHUWING Er bestaat explosiegevaar als de batterij wordt vervangen door een verkeerd type. Vervang de batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt.

  • Page 154: Backplane Voltage

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Attention Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout courant électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées. ‫אחד‬ ‫מספק‬ ‫יותר‬ ‫קיים‬ ‫אם‬ !‫אזהרה‬...
  • Page 155 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 警告 當系 統正 在進 行時 ， 背 板上 有危 險的 電壓或 能量 ， 進 行維 修時 務必 小心 。 Warnung Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche Spannungen oder Energien auf.

  • Page 156: Comply With Local And National Electrical Codes

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Comply with Local and National Electrical Codes Warning! Installation of the equipment must comply with local and national electrical codes. 地方 および国の電 気規 格に準 拠 機器 の取り 付 けはその地方および国の電気 規格 に準拠 する必 要があり ます。...

  • Page 157: Product Disposal

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 경고! 현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다. Waarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften. Product Disposal Warning! Ultimate disposal of this product should be handled according to all national laws and regulations.

  • Page 158: Fan Warning

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent. ‫המוצר‬ ‫סילוק‬ !‫אזהרה‬ ‫המדינה‬...
  • Page 159 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 警告 ! 警 告！ 危 险 的 可 移 动 性 零 件 。 请 务 必 与 转 动 的 风 扇 叶 片 保 持 距 离 。 当 您 从 机 架 移 除 风 扇...

  • Page 160: Power Cable And Ac Adapter

    タ ー を 該 当 する地 域 の条 例 や安 全 基 準 に適 合 するコ ード サイ ズやプラ グと 共 に使 用 下 さ い。 他 の ケー ブルやアダ プタ を使 用すると 故障 や火災の原 因になるこ と があり ます。 電 気 用 品 安 全 法 は、 ULまたはCSA認 定 のケーブル(UL/CSAマーク がコ ード に表 記 )を Supermicro が指定 する製品 以外 に使 用するこ と を禁止 し ています。...
  • Page 161 遵 照 当 地 法 规 和 安 全 要 求 的 合 规 的 电 源 线 尺 寸 和 插 头.使 用 其 它 线 材 或 适 配 器 可 能 会 引 起 故 障 或 火 灾 。 除 了 Supermicro所 指 定 的 产 品,电 气 用 品 和 材 料 安 全 法 律 规 定 禁 止 使 用...
  • Page 162 준수하여 제공되거나 지정된 연결 혹은 구매 케이블, 전원 케이블 및 AC 어댑터를 사용하십시 오. 다른 케이블이나 어댑터를 사용하면 오작동이나 화재가 발생할 수 있습니다. 전기 용품 안전법 은 UL 또는 CSA 인증 케이블 (코드에 UL / CSA가 표시된 케이블)을 Supermicro 가 지정한 제품 이외의 전기 장치에 사용하는 것을 금지합니다.

  • Page 163: Warning Definition

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Stroomkabel en AC-Adapter Waarschuwing! Bij het aansluiten van het Product uitsluitend gebruik maken van de geleverde Kabels of een andere geschikte aan te schaffen Aansluitmethode, deze moet altijd voldoen aan de lokale voorschriften en veiligheidsnormen, inclusief de juiste kabeldikte en stekker. Het gebruik van niet geschikte Kabels en/of Adapters kan een storing of brand veroorzaken.
  • Page 164 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät...

  • Page 165: Installation Instructions

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ٌ ‫ز‬ ‫!ﺗﺤﺬ‬ ‫ﺧﻄﺰ‬ ٌ ‫ع‬ ‫اﻟﺰﻫﺰ‬ ‫ﻫﺬا‬ ٌ ‫ة‬ ‫ﺟﺴﺬ‬ ‫اﺻﺎﺑﺔ‬ ‫ف‬ ‫ﺗﺘﺴﺒﺐ‬ ‫أى‬ ‫و ٌﻛﻲ‬ ‫ﺣﺎﻟﺔ‬ ‫ف‬ ‫ك ً ا‬ ‫اﻟﺬواﺋﺰ‬ ‫ﻋﻲ‬ ‫ا ﺟ ٌﻮة‬ ‫ال‬ ‫ﺑﺎﻟﻮﺧﺎﻃﺰ‬ ‫ﻋﻠﻦ‬ ‫ﻋﻠﻰ‬ ‫ﻫﻌﺬات،ﻛﻲ‬...

  • Page 166: Circuit Breaker

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 警告 將系 統與 電源 連接 前， 請先 閱讀 安裝 說明 。 Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
  • Page 167 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems サーキッ ト ・ ブレーカ ー こ の製品 は、 短 絡( 過 電流 ) 保 護装 置がある建 物での設置 を前提 と し ています。 保護 装置 の定格 が250 V、 20 Aを超えないこ と を確認 下さ い。...

  • Page 168: Power Disconnection Warning

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ‫ﻓﻲ‬ ‫ﺗﺜﺒﻴﺘﻬﺎ‬ ‫ﺗﻢ‬ ‫اﻟﺘﻲ‬ ‫اﻟﺪواﺋﺮاﻟﻘﺼﻴﺮة‬ ‫ﻣﻪ‬ ‫اﻟﺤﻤﺎﻳﺖ‬ ‫ﻣﻌﺪاث‬ ‫ﻋﻠﻰ‬ ‫ﻳﻌﺘﻤﺪ‬ ‫اﻟﻤﻨﺘﺞ‬ ‫ﻫﺬا‬ ‫اﻟﻤﺒﻨﻰ‬ 20A, 250V : ‫ﻣﻦ‬ ‫أﻛﺜﺮ‬ ‫ﻟﻴﺲ‬ ‫اﻟﻮﻗﺎﺋﻲ‬ ‫اﻟﺠﻬﺎز‬ ‫ﺗﻘﻴﻴﻢ‬ ‫أن‬ ‫ﻣﻦ‬ ‫ﺗﺄﻛﺪ‬ 경고! 이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장...
  • Page 169 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Warnung Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder zu entfernen.

  • Page 170: Equipment Installation

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Equipment Installation Warning! Only authorized personnel and qualified service persons should be allowed to install, replace, or service this equipment. 機器 の設置 トレーニングを受 け認 定 さ れた人 だけがこ の装 置 の設 置 、 交 換 、 またはサービスを許 可 さ れていま...

  • Page 171: Restricted Area

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ‫ﺻﻴﺎﻧﺘﻪ‬ ‫أو‬ ‫اﺳﺘﺒﺪاﻟﻪ‬ ‫أو‬ ‫اﻟﺠﻬﺎز‬ ‫ﻫﺬا‬ ‫ﺑﺘﺮﻛﻴﺐ‬ ‫اﻟﻤﺆﻫﻠﻴﻦ‬ ‫اﻟﺨﺪﻣﺔ‬ ‫وأﻓﺮاد‬ ‫اﻟﻤﻌﺘﻤﺪﻳﻦ‬ ‫ﻟﻠﻤﻮﻇﻔﻴﻦ‬ ‫ﻓﻘﻂ‬ ‫اﻟﺴﻤﺎح‬ ‫ﻳﻨﺒﻐﻲ‬ 경고! 승인된 직원과 자격을 갖춘 서비스 담당자만이 이 장비를 설치, 교체 또는 서비스할 수 있습니 다. Waarschuwing Alleen geautoriseerd personeel en gekwalificeerd onderhoudspersoneel mag deze apparatuur installeren, vervangen of onderhouden.
  • Page 172 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Warnung Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich. ¡Advertencia! Esta unidad ha sido diseñada para instalación en áreas de acceso restringido. Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una herramienta especial,...

  • Page 173: Battery Handling

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Waarschuwing Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang. Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

  • Page 174: Redundant Power Supplies

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ATTENTION Il existe un risque d'explosion si la batterie est remplacée par un type incorrect. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant.
  • Page 175 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 冗長 電源 装置 こ のユニッ ト は複数 の電源 装置 が接続 さ れている場 合があり ます。 ユニッ ト の電 源を切 るためには、 すべての接 続を取 り 外 さ なければなり ません。 警告 此部 件连 接的 电源 可能 不止 一个 ， 必 须将所 有电 源断 开才 能停 止给 该部 件供 电 。...

  • Page 176: Backplane Voltage

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 경고! 이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을 차단 하기 위해서는 모든 연결 단자를 제거해야만 합니다. Waarschuwing Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

  • Page 177: Comply With Local And National Electrical Codes

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Attention Lorsque le système est en fonctionnement, des tensions électriques circulent sur le fond de panier. Prendre des précautions lors de la maintenance. ‫האחורי‬ ‫בפנל‬ ‫מתח‬ !‫אזהרה‬ ‫במהלך‬ ‫להיזהר‬ ‫יש‬ .‫המערכת‬ ‫תפעול‬...
  • Page 178 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 警告 設備 安裝 必須 符合 本地 與本 國電 氣法 規 。 Warnung Die Installation der Geräte muss den Sicherheitsstandards entsprechen. ¡Advertencia! La instalacion del equipo debe cumplir con las normas de electricidad locales y nacionales.

  • Page 179: Product Disposal

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems Product Disposal Warning! Ultimate disposal of this product should be handled according to all national laws and regulations. 製品 の廃棄 こ の製 品 を廃 棄 処 分 する場 合 、 国 の関 係 する全 ての法 律 ・ 条 例 に従 い処 理 する必 要 があり ま...

  • Page 180: Fan Warning

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ‫המוצר‬ ‫סילוק‬ !‫אזהרה‬ ‫המדינה‬ ‫וחוקי‬ ‫להנחיות‬ ‫בהתאם‬ ‫להיות‬ ‫חייב‬ ‫זה‬ ‫מוצר‬ ‫של‬ ‫סופי‬ ‫סילוק‬ ‫اﻟﯩﻄﻨﻴﺔ‬ ‫واﻟﻠﯩﺎﺋﺢ‬ ‫اﻟﻘﯩﺎﻧﻴﻦ‬ ‫ﻟﺠﻤﻴﻊ‬ ‫وﻓﻘﺎ‬ ‫ﻣﻌﻪ‬ ‫اﻟﺘﻌﺎﻣﻞ‬ ‫ﻳﻨﺒﻐﻲ‬ ‫اﻟﻤﻨﺘﺞ‬ ‫ﻫﺬا‬ ‫ﻣﻦ‬ ‫اﻟﻨﻬﺎﺋﻲ‬ ‫اﻟﺘﺨﻠﺺ‬ ‫ﻋﻨﺪ‬ 경고! 이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
  • Page 181 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 警告 ! 警 告！ 危 险 的 可 移 动 性 零 件 。 请 务 必 与 转 动 的 风 扇 叶 片 保 持 距 离 。 当 您 从 机 架 移 除 风 扇...

  • Page 182: Dc Power Supply

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ‫أن‬ ‫اﻟﻤﻤﻜﻦ‬ ‫اﻟﻤﺘﺤﺮﻛﺔ.ﻣﻦ‬ ‫اﻟﻤﺮوﺣﺔ‬ ‫ﺷﻔﺮات‬ ‫ﻋﻦ‬ ‫اﺑﺘﻌﺪ‬ .‫ﺧﻄﺮة‬ ‫ﻣﺘﺤﺮﻛﺔ‬ ‫أﺟﺰاء‬ !‫ﺗﺤﺬﻳﺮ‬ ‫اﻷﺻﺎﺑﻊ‬ ‫إﺑﻘﺎء‬ ‫ﻳﺠﺐ‬ ‫اﻟﻬﻴﻜﻞ‬ ‫ﻣﻦ‬ ‫اﻟﻤﺮوﺣﺔ‬ ‫ﻛﺘﻠﺔ‬ ‫إزاﻟﺔ‬ ‫ﺗﺪورﻋﻨﺪ‬ ‫ﺗﺰال‬ ‫ﻻ‬ ‫اﻟﻤﺮاوح‬ ‫اﻟﻤﺮوﺣﺔ‬ ‫ﻛﺘﻠﺔ‬ ‫ﻓﻲ‬ ‫اﻟﻔﺘﺤﺎت‬ ‫ﻋﻦ‬ ‫ﺑﻌﻴﺪا‬ ‫اﻷﺷﻴﺎء‬ ‫ﻣﻦ‬ ‫وﻏﻴﺮﻫﺎ‬...
  • Page 183 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 警告 需 要 使 用 绞 线 连 接 时， 请 使 用 经 认 可 的 连 接 端 子， 如 闭 环 端 子 或 具 有 接 线 柱 的 铲 形 端...
  • Page 184 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 주의! 꼬인 배선이 요구 될 때에는 폐회로나 돌출부가 위로 튀어 나온 Spade형태의 승인된 배선 터미 네이션들을 사용하세요. 이 터미네이션들은 배선들을 위해 적절한 크기여야 하고, 절연체와 도체 모두를 고정시킬 수 있 어야 합니다.

  • Page 185: Hazardous Voltage Or Energy Present On Dc Power Terminals

    SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema.
  • Page 186 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems 警告 直 接 電 力 端 子 に危 険 な電 圧 やエネルギーが発 生 している可 能 性 があり ます。 使 用 していない端 子 には常 にカ バーをつけてく ださ い。 カ バーがついていると きは非 絶 縁 形 コ ンダク タ ーに接 触 していな...
  • Page 187 SuperServer SYS-112HA-TN: Standardized Warning Statements for AC Systems ‫ﺗﺤﺬﻳﺮ‬ .‫اﻟﺨﺪﻣﺔ‬ ‫ﻓﻲ‬ ‫اﻟﻄﺮﻓﻴﺔ‬ ‫اﻷﺟﻬﺰة‬ ‫ﺗﻜﻮن‬ ‫ﻻ‬ ‫ﻋﻨﺪﻣﺎ‬ ‫داﺋ ﻤ ًﺎ‬ ‫اﻟﻐﻄﺎء‬ ‫اﺳﺘﺒﺪل‬ .‫اﻟﻤﺴﺘﻤﺮ‬ ‫اﻟﺘﻴﺎر‬ ‫ﻃﺎﻗﺔ‬ ‫أﻃﺮاف‬ ‫ﻋﻠﻰ‬ ‫ﺧﻄﺮة‬ ‫ﻃﺎﻗﺔ‬ ‫أو‬ ‫ﺟﻬﺪ‬ ‫ﻫﻨﺎك‬ ‫ﻳﻜﻮن‬ ‫ﻗﺪ‬ ‫ﻣﻜﺎﻧﻪ‬ ‫ﻓﻲ‬ ‫اﻟﻐﻄﺎء‬ ‫ﻳﻜﻮن‬ ‫ﻋﻨﺪﻣﺎ‬ ‫اﻟﻤﻌﺰوﻟﺔ‬ ‫ﻏﻴﺮ‬...

  • Page 188: System Specifications

    System Specifications Appendix C: System Specifications Processor ® ® Single Intel Xeon 6900-series processor with P-cores (in Socket BR LGA7529) and a thermal design power (TDP) of up to 500 W Chipset System on Chip BIOS AMI 64 MB SPI Flash Memory 12 DIMM slots Max Memory (1DPC): 3 TB 8800 MT/s ECC DDR5 MRDIMM...
  • Page 189 System Specifications System Cooling Eight counter-rotating 40x40x56 mm fans One CPU air shroud Power Supply Two 1200 W Redundant (1 + 1) Titanium Level (96%) power supplies or Two 1300 W DC Redundant (1 + 1) Gold Level power supplies or Two 1600 W Redundant (1 + 1) Titanium Level (96%) power supplies or Two 2000 W Redundant (1 + 1) Titanium Level (96%) power supplies Input 800 W: 100-127 Vac...
  • Page 190 System Specifications Applied Directives, Standards EMC/EMI: 2014/30/EU (EMC Directive) Electromagnetic Compatibility Regulations 2016 FCC Part 15 ICES-003 VCCI-CISPR 32 AS/NZS CISPR 32 BS/EN55032 BS/EN55035 CISPR 32 CISPR 35 BS/EN 61000-3-2 BS/EN 61000-3-3 BS/EN 61000-4-2 BS/EN 61000-4-3 BS/EN 61000-4-4 BS/EN 61000-4-5 BS/EN 61000-4-6 BS/EN 61000-4-8 BS/EN 61000-4-11...

Table of Contents