Draper FlexStyle UpLift Instructions Manual
Draper FlexStyle UpLift Instructions Manual

Draper FlexStyle UpLift Instructions Manual

Cordless operated open roll shade

Advertisement

Quick Links

FlexStyle
UpLift
®
Cordless operated open roll shade

Overview - Components

FLSTYLE UPLIFT
Please Note:
Your UpLift FlexShade operator has
been pre-rotated to optimize spring
tension. See roller label for number of
pre-rotations. If shade tension requires
additional adjustment, see Page 7.
B R A
O P E
R A T
B R A
O R
C K E
T
B R A
C K E
C O V
T
E R
IMPORTANT:
Retaining Clip
must be removed
from shade prior
to operation.
TOOLS
REQUIRED
PENCIL
Contents
Overview - Components .......................................................................................1
Section 1 - Installing Mounting Brackets ..........................................................3
Section 2 - Mounting Shade ................................................................................4
O P E
R A T
C K E
O R
T
C A P
E N D
R E T
A I N
C L I
I N G
P
TAPE MEASURE
LEVEL
POWER DRILL
PLIERS
Section 3 - Shade Operation ...............................................................................6
Section 5 - Adjusting Shade Tension .................................................................7
Section 6 - Bracket Dimensions .........................................................................8
Section 7 - Shade Dimensions ............................................................................8
INSTRUCTIONS
INSTALLATION & OPERATION
B R A
C K E
T
C A P
S P A
C E R
I D L
E R
E N D
IMPORTANT:
Spacer is included
for use for possible
tension adjustments.
Install only if needed
(See P.7)
discard!
CAUTION
Read and understand
all warnings before
beginning installation.
HARDWARE
(by others)
(Removal Tool must be ordered separately.)
If you have any difficulties installing or servicing your
FlexStyle UpLift, call your dealer or Draper, Inc.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
|
FORM: FlexStyle_Uplift_Inst25
© 2025 All Rights Reserved
B R A
C K E
C O V
T
E R
I D L
E R
B R A
C K E
T
. Do not
6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FlexStyle UpLift and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Draper FlexStyle UpLift

  • Page 1: Table Of Contents

    Section 7 - Shade Dimensions ................8 If you have any difficulties installing or servicing your FlexStyle UpLift, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 FORM: FlexStyle_Uplift_Inst25...
  • Page 2: Before Beginning Installation

    Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy If the shade is telescoping, place a piece of shimming water.
  • Page 3: Section 1 - Installing Mounting Brackets

    Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions. WARNING: UpLift operator should not be used with products or pockets having a bottom closure without written permission from Draper. Mark wall or ceiling Drill small starter hole...
  • Page 4: Section 2 - Mounting Shade

    FlexStyle UpLift ® page 4 of 8 Section 2 - Mounting Shade Place spring-loaded pin Please Note: into idler end bracket. ALWAYS START AT THE IDLER END OF SHADE. This varies from left to right, depending on whether installation is standard roll or reverse roll.
  • Page 5 FlexStyle UpLift ® page 5 of 8 Slide Bracket Covers over brackets. Ensure that Bracket Cover SNAPS into place. (Idler Bracket shown.) Attach hem bar handle onto the Depending upon hem bar type , handle will (shown at left) desired placement on hem bar. either snap or adhere onto hem bar.
  • Page 6: Section 3 - Shade Operation

    FlexStyle UpLift ® page 6 of 8 Section 3 - Shade Operation Pull-Down Wand To lower window shade The Pull-Down Wand (Part Number Grasp center of hem bar, can be ordered C061.051) or hem bar clip. separately to assist in raising Pull shade down and lowering shades installed to desired position.
  • Page 7: Section 4 - Removing Bracket Covers

    FlexStyle UpLift ® page 7 of 8 Section 4 - Removing Bracket Covers Please Note: The Cover Removal Tool is available if bracket covers need to be detached for any reason. Grasp the flat end of the bracket. Pull off Bracket Cover.
  • Page 8: Section 6 - Bracket Dimensions

    FlexStyle UpLift ® page 8 of 8 Section 6 - Bracket Dimensions C002.1820 (Motor End, Extended) C002.1822 (Idler End, Extended) " " (5mm) (5mm) " (5mm) " " (17.5mm) (15mm) 2 " 2 " (58.8mm) " (58.8mm) " (15mm) (17.5mm) "...

Table of Contents