Summary of Contents for Kichler Lighting Decor 54 Link 300168
Page 1
Model: 300168 READ AND SAVE THESE INSTRUCTIONS...
Page 2
1. SAFETY RULES 8. To operate the reverse function on this 1. CAUTION - To reduce the risk of electric fan, press the reverse button while the fan shock, insure electricity has been is running. turned off at the circuit breaker or fuse box before beginning.
Page 3
54"Link 1. SAFETY RULES (continued) WARNING • INGESTION HAZARD: This product contains a button cell or coin battery. • DEATH or serious injury can occur if ingested. • A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours. •...
Page 4
1. NORMAS DE SEGURIDAD (continuación) AVERTISSEMENT • RISQUE D’INGESTION : Ce produit contient une pile bouton. • La MORT ou des blessures graves peuvent survenir en cas d’ingestion. • Une pile bouton avalée peut provoquer des brûlures chimiques internes en 2 heures seulement. •...
Page 5
54” Lehr 1. RÈGLES DE SÉCURITÉ (suite) ADVERTENCIA • PELIGRO DE INGESTIÓN: Este producto contiene una pila tipo botón o tipo moneda. • En caso de ingestión puede producirse la MUERTE o lesiones graves. • La ingestión de una pila tipo botón o tipo moneda puede provocar Quemaduras Químicas Internas en tan sólo 2 horas.
2. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: Fan blades (2) Fan motor assembly CoolTouch™...
54"Link 4. MOUNTING OPTIONS If there isn't an existing ETL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and Outlet box building materials.
5. REMOVE THE MOUNTING PLATE Mounting plate REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Step 1. Remove the mounting plate from the fan motor by removing the nuts. (Fig. 4) Fan motor Fig.
54"Link 7. ELECTRICAL CONNECTIONS WARNING: To avoid possible electrical shock, be sure you have turned off the power at the Outlet box main circuit panel. White ("AC IN N") Follow the steps below to connect the fan to Black ("AC IN L") Green or bare copper (ground) your household wiring.
8. FINISHING THE INSTALLATION Step 1. Move fan into position over the four mounting studs and secure with the provided Screws nuts. (Fig. 8) Step 2. Raise the motor housing up against the mounting plate, the four supports inside Nuts the housing should be placed against the four studs on mounting plate, twist the housing clockwise until snug.
54"Link 9. ATTACHING THE FAN BLADES Step 1. Attach a blade to a blade bracket with the Allen screws (with lock washers) and filat washers and fasten using the Allen wranch provided. (Fig. 10) Place the gasket into blade bracket. Make sure the blade is straight when set on the blade bracket.
10. CONTROL SYSTEM SET-UP WARNING: Chemical Burn Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause Set screw severe internal burns and can lead to death in as little as 2 hours.
Page 13
54"Link System Programing: Read all of these steps Blue Light BEFORE proceeding. Each step must be followed exactly to properly program the control system. 1. You can leave the frequency switches at the factory setting or move them to any combination of up or down.
Page 14
Speed Buttons 11. OPERATING INSTRUCTIONS: Figure 15 1. Buttons 1, 2, 3, 4, 5 and 6 are used to set the blade speed as follows: 1 = Low Speed 2 = Medium Low Speed 3 = Medium Speed 4 = Medium High Speed 5 = High Speed 6 = Extra High Speed Figure 16...
Page 15
54"Link NOTE: Please remember your control system is an RF (Radio Frequency) control system. You may occasionally experience control problems because of other radio frequency interference, i.e. fan turns off, light turns off or won't turn on, speed changes, etc. If this should happen, just change the “Control Frequency”...
Page 16
SENSOR DC CONTROL PAIRING PROCEDURES IMPORTANT: Ceiling fan blades MUST be installed before pairing procedure can begin. Step 1. Program the wall control and/or the handset control separately. Once the following pairing is successfully done, both the wall control and the handset control can be used for the fan.
54"Link ™ 12. INSTALLING THE COOLTOUCH Outlet box CONTROL SYSTEM WALL PLATE Switch NOTE: All wiring must be in accordance with the Wall plate National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. Select a location to install your CoolTouch™...
14. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. 3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.
Page 19
54” Lehr FCC INFORMATION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the Decor 54 Link 300168 and is the answer not in the manual?
Questions and answers