Table of Contents
Advertisement
Quick Links
Instructions manual
Automatic mini turntable with the multifunction
bottling, pumping and creaming machine
Przedsiębiorstwo Pszczelarskie Tomasz Łysoń
Spółka z o.o. Spółka Komandytowa
34-125 Sułkowice, ul. Racławicka 162, Polska
www.lyson.com.pl, email:
lyson@lyson.com.pl tel.33/875-99-40, 33/870-
64-02
Headquarters: Klecza Dolna 148, 34-124 Klecza Górna
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for LYSON W204013PZ
Summary of Contents for LYSON W204013PZ
- Page 1 Instructions manual Automatic mini turntable with the multifunction bottling, pumping and creaming machine Przedsiębiorstwo Pszczelarskie Tomasz Łysoń Spółka z o.o. Spółka Komandytowa 34-125 Sułkowice, ul. Racławicka 162, Polska www.lyson.com.pl, email: lyson@lyson.com.pl tel.33/875-99-40, 33/870- 64-02 Headquarters: Klecza Dolna 148, 34-124 Klecza Górna...
-
Page 2: Table Of Contents
The manual covers following devices (codes): W204013PZ Table of contents 1. General safety instructions 1.1. Intended use 1.2. Electrical safety 1.3. Operation safety 2. Instructions for use 2.1. General instructions – preparation for use 2.2. Operation instructions 3. Product description 3.1. -
Page 3: General Safety Instructions
1. General safety instructions 1.3. Operation safety Before first use read the manual carefully and follow 1. The device is not intended for use by persons the instructions contained therein. The manufacturer (including children) with limited physical, sensory or is not liable for damage caused by equipment used mental abilities, or by inexperienced users, unless inappropriately or by incorrect handling. -
Page 4: Operation Instructions
2.2 Operation instructions Elements: 1. The device is designed to automatically fill the Turntable’s controller unit honey into the jars. Emergency „STOP” button 2. The device has to be cleaned before the first Table base use and after finishing work according to the instructions in the "Cleaning and Maintenance"... -
Page 5: Buttons And Dials
Buttons and dials: Fig.4 speed control dial service mode START button bottling process indicator STOP button power indicator bottling mode START button Back panel – Fig.3 Emergency „STOP” limit switch 3.3 Error codes Elements: main switch 0-1 power cord socket 230V 10A fuse Internal CONTROLLER fault position (limit) switch socket... -
Page 6: Bottling Machine
6. When the honey poured earlier into the pipe is pumped, stop the pump by pressing the button „STOP”. 7. Once this has been done, insert the hose into the honey barrel and start bottling or pumping 8. Run a small amount of honey through to remove any air left in the tube. -
Page 7: Bottling Mode
4.3. Bottling mode Basic mode parameters Presented FM-02 controller is a device that Programming the dispensing mode of the controller is done controls the operation of the dosing pump and controls the by modifying a set of parameters that configure the execution of the creaming cycle. -
Page 8: Creaming/Pumping Mode
4.4. CREAMING / PUMPING MODE The process of creaming using a dispenser is based on the principle of pumping honey from one container to another. The process consists in cyclical pumping of the honey over several days until the appropriate consistency is achieved. -
Page 9: Controller Diagnostics
Section Description Indication ERROR Reduces the timer time after which the pump will stop automatically. The display The display of a 00:00:00 deactivates the automatic pump Lower stop function. Change of setting possible value other than „minus” in start mode button 1E9705 indicates... -
Page 10: Error Codes
Testing button 0 / 1 operation 7. Measure the temperature inside the Testing button controller box. 0 / 1 operation 8. The readings should not TEMP [ o C] 5 - 65 exceed the 4.6. Error Codes specified range. The FM-02 controller is equipped with advanced error detection mechanisms. -
Page 11: Controller Configuration
STATUS OK / ---- The ERROR indication signals the detection of a controller RAM The ERROR indication means data consistency error. This that the button was pressed situation is possible when the immediately after the power controller operates in an was switched on. -
Page 12: Bottling Settings
Then pour approximately 1 kg of honey into the other end of the tube. hold the hose up until the honey flows into the toothed module. the tube is transparent so you can see when the honey flows into the module. when the honey flows into the module place the hose in the honey container press and hold the "No8"... - Page 13 – v1 honey pouring speed - e.g. 100%. If the honey is Adjustment range 0-50 pumped too quickly and aerates too much, then we The parameter setting does not disappear after switching off the power supply. decrease the filling speed, e.g. to 70%. - p4 - Negative weight calibration (1g) The range of adjustment is 50[%] - 100[%].
-
Page 14: Creaming/Pumping Settings
4.9. Creaming/Pumping settings The honey creaming mode involves pumping the honey, i.e. running the pump in continuous mode. The controller gives the option to set pumping/creaming for a specific time. Fot. 10 Switch off pumping mode button nr7 (STOP) 4.10. Pumping timer and speed settings - To set pumping for a specific period of time, e.g.: for 20min. -
Page 15: Storage
Fot. The top button "plus" (No.1) or Step 1-unscrew the 4 knobs from the dosing module (from the front of the machine). "minus"(no2) is used to increase or decrease the pumping/creaming speed 5. Storage Clean and dry the unit thoroughly after use. If the device has been moved from a cold room to a room with a higher temperature, before switching on wait until it reaches the ambient temperature and all condensation... -
Page 16: Optional Accessories
9. Warranty The product purchased from the Lyson Company is covered by a manufacturer's warranty. The warranty period is 24 months from the date of purchase. All purchased products come with receipts or VAT invoices.
Need help?
Do you have a question about the W204013PZ and is the answer not in the manual?
Questions and answers