Siruba DL7200S Parameter Manual
  1. Manuals
  2. Brands
  3. Siruba Manuals
  4. Sewing Machine
  5. DL7200S
  6. Parameter manual
Siruba DL7200S Parameter Manual

Siruba DL7200S Parameter Manual

Electronic control
Hide thumbs

Advertisement

Table of Contents

電控參數說明書
ELECTRONIC CONTROL PARAMETER MANUAL
DL7200S

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DL7200S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Siruba DL7200S

Summary of Contents for Siruba DL7200S

  • Page 1 電控參數說明書 ELECTRONIC CONTROL PARAMETER MANUAL DL7200S...
  • Page 2 1） 2） 3） 4） 5） 6） 7） 8） 9） 10） 11） 12） 13） 14） 15） 16）...
  • Page 16 Safety Instruction 1. Users are required to read the operation manual completely and carefully before installation or operation. 2. The product should be installed and pre-operated by well-trained persons. All power supplies must be turned off during the installation work, remember not to operate with power on. 3.

  • Page 17: Key Description

    1 Key displays and operating instructions 1.1 Key description Name Indicate If click, enter or exit the user parameter setting interface. Function If long-press, it will switch to the password input interface. Enter the correct parameter edit password, press S key to confirm, you can enter the advanced parameter setting interface.

  • Page 18: Auxiliary Function

    If click, switch starting tight seam, ending tight seam, full function and Tight seam function off successively. setting If long-press, switch to tight seam mode editing interface. Pattern backing- If click, set used or cancelled pattern backing-tacking function. tacking setting If long-press, switch to pattern backing-tacking mode editing interface.

  • Page 19: User Parameter

    On the main interface long-press to shift pattern freedom sewing mode editing interface“n-01 01”，short-press the 4th column to adjust n01-n09, short-press adjust 01-10 segment number, adjust to setting pattern number, segment number, short-press S key to confirm, shift to corresponding pattern number editing interface “01 1 3.0”， short press 1st column or 2nd column to adjust 00-99 stitches, short-press 4th column 1-9 repeat times, short-press adjust stitch length, after finished setting short-press S key to confirm.
  • Page 20 Items Range Default Description ON: After executing the constant-stitch sewing, the back-tacking sewing will be executed automatically. In any sewing mode, mending stitch Automatic end back-tacking function cannot be used. sewing after constant-stitch ON/OFF OFF: After executing the last constant-stitch sewing sewing, the back-tacking sewing function will not be automatically executed, and the front step or full...
  • Page 21 Items Range Default Description selection 1: ON Automatic piece counting 0: Incremental piecework mode P17-N13 mode selection 1: Diminishing piecework mode Stitch compensation for start back-tacking A section, 0~200 action gradually delay; The large Start back-tacking 0-200 compensation 1 value, the longer of the A section last stitch, and the shorter of the B section first stitch.
  • Page 22 Items Range Default Description Thread tension releasing 0: OFF 1: ON function selection 0 : OFF Thread wiping function / 1: Thread wiping function Thread clamping function 0-11 2-11: Thread clamping Function and the strength of selection automatic thread clamping. Automatic thread trimming ON/OFF function selection...
  • Page 23 Items Range Default Description pattern sewing action Motor stop with a reverse ON/OFF angle after trimming function Start from the upper needle position and adjust the Adjust the reverse angle when 10-300 angle of the needle lift in reverse operation after motor stop after trimming trimming.
  • Page 24 Items Range Default Description position (value) as up needle position. Adjust lower needle stop position, the displayed value will change with the position of the Lower positioning quick 0-359 adjustment handwheel, press "S" key to save the current position (value) as down needle position. Tacking stitch length -100~100 compensation...
  • Page 25 Items Range Default Description random change it will result the control box and motor abnormal or damaged). The starting time of the half 10-900 back pedaling function (ms) Thread tension releasing 1-10 protection time (s) Starting tight seam stitch 0-5.0 length Direction of starting tight P100...
  • Page 26 Items Range Default Description The suction time for clamp P116 0-5000 function without any thrum Duty cycle for thread pushing 0-100 P117 with clamp function without any thrum Function selection of manual P118 back-tacking button in pattern mode Electromagnet overcurrent P119 protection detection switch Kneeling device starting AD...
  • Page 27 Items Range Default Description Tacking stitch length P144 -100~100 compensation in high speed Back-tacking stitch length P145 -100~100 compensation in high speed P146 Presser foot speed 50-800 When sewing, the highest P148 presser foot lift height of 0-4799 2000 electric knee-control P153 Ending tight seam stitch length 0-5.0...
  • Page 28 Items Range Default Description 0: OFF 1: Half stitch 2: One stitch P175 Manual Switch C 3: Continuous half stitch 4: Continuous one stitch 5: Back-tacking when machine stop or pause 6: Tight seam function 0: OFF 1: Half stitch 2: One stitch P176 Manual Switch D...
  • Page 29 Items Range Default Description Periodic signal of the first P211 1-100 thread tension release output action (%) Thread tension release the first P212 1-100 output action time The main shaft angle when returning to normal stitch P226 0-359 length when starting a stitch or cranking the handwheel by hand Stepping first stroke when...

  • Page 30: Error Code List

    Items Range Default Description Stepping motor zero-point P252 0-4799 position of the thread trimming adjustment Stepping motor zero-point P253 0-4799 position of the presser foot adjustment 7mm tacking stitch length P254 -100~100 compensation in high speed 7mm back-tacking stitch P255 length compensation in high -100~100 speed...
  • Page 31 2. If there is no alarm after removing the solenoid connector, please plug it back in 1) Step on the front pedal to let the sewing machine perform thread clamping and back-tacking. If alarms, please turn off start back-tacking and end back-tacking, restart the control box, and then step forward.
  • Page 32 clear and re-count.) Insufficient bobbin thread Please add bobbin thread. warning Abnormal communication between main chip and drive Please replace the control box and notify the after-sales service. chip 1. Turn off the system power and observe whether back-tacking stepping motor is stuck.

  • Page 33: Port Diagram

    tacking motor and the encoder connector are loose or fall off, restore them to normal and restart the system. 2. If it still does not work normally, please replace the control box or back- tacking stepping motor and notify the after-sales service. 4 Port diagram 8P function port description 1.
  • Page 34 由於對產品的改良及更新，本產品使用說明書中與零件圖之產品及外觀的修改恕不事先通知 ! The specification and/or appearances of the equipment described in this instruction book & parts list are subject to change because of modification which will without previous notice. BYL-13S62.AUG.2024...

Table of Contents