Connecting The Subwoofer - Yamaha RX-A2000 Owner's Manual

1 1
Connect the speakers
Subwoofer
HDMI HDMI
AV A A 1 AV 1 AV 2 AV A A 2 AV A A 3 AV 3 A A 4 AV 4 AV AV 5 AV A A 5
(1 BD/DVD) (1 BD/DVD)
COMPONENT VIDEO COMPONENT VIDEO
P P P P Y Y P P P P
B B R R AV AV 3 A A 3 B B C C R R
MONITOR OUT/ZONE OUT MONITOR OUT/ T T Z / / ONE OUT
Y Y P P P P
B B R R
D D
AV 4 AV A A 4
MULT MULTI CH INPUT L L I CH INPUT
ZONE OUT ZONE OUT PRE OUT PRE OUT
CENTER CENTER
FRONT/ T T FRONT/
FRONT FRONT SURROUND SURROUND SUR. BACK SUR. BACK SUBWOOFER SUBWOOFER ZONE 2 ZONE 2 ZONE 3 ZONE 3 SURROUND SURROUND
F. F F PRESENCE F. PRESENCE
SPEAKERS
NE3 NE3 SURROUND SURROUND BACK/
BI-AMP
SINGLE
7.1 7.1
R L
Surround 6.1
speaker
R L
Surround back
speaker
Connecting speakers
2 2
1
Remove approximately 10 mm (0.4 in) of
insulation from the ends of the speaker cables,
and twist the bare wires of the cables together
fi rmly so that they will not cause short circuits.
2
Loosen the speaker terminals.
3
Insert the bare wire of the speaker cable into the
gap on the side of the terminal.
4
Tighten the terminal.

Connecting the subwoofer

1
Connect the subwoofer input jack to the SUBWOOFER
1 jack on this unit with an audio pin cable.
Front speaker
R L
RS-232C RS-232C
AV 6 AV A A 6 AV 7 AV A A 7
TRIGGER TRIGGER
OUT OUT
1 1
REMOTE REMOTE
1 1 2 2
IN IN OUT OUT IN IN OUT OUT
2 2
+12V 0.1A MAX. +12V 0.1A MAX.
(SINGLE) (SINGLE) (FRONT)
1
2 2
(REAR) (REAR) ( ( ) ) ) )
SUR. BACK SUR. BACK CENTER CENTER
SUBWOOFER SUB WOOF E R
CENTER FRONT ZONE2/ZONE3/ ZONE2/Z / / ONE3/
F.PRESENCE F. F F PRESENCE
EXTRA SP1 EXTRA SP1
Center speaker
3
F R
O N
T
1
4 4
7.1
Connect when using with 7.1-channel speaker layout.
6.1
Connect when using with 6.1-channel speaker layout.
Caution:
• Remove the power cable of this unit from the power outlet before
connecting the speakers.
• Generally speaker cables consist of two parallel insulated
cables. One of these cables is a different color, or has a line
running along it, to indicate different polarity. Insert the different
colored (or lined) cable into the "+" (positive, red) terminal
on this unit and the speakers, and the other cable into the "-"
(minus, black) terminal.
• Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this unit.
This may damage this unit or the speakers. If the speaker cables
short circuit, "CHECK SP WIRES!" will appear on the front panel
display when this unit is switched on.
• This unit is confi gured for 8 Ω speakers at the factory setting.
When connecting 6 Ω speakers, confi gure the speaker
impedance setting of this unit to 6 Ω. When this unit is
confi gured for 6 Ω speakers, 4 Ω speakers can also be used as
the front speakers. For more information on setting the speaker
impedance, refer to "Changing speaker impedance" in the
Owner's Manual.
• When connecting the presence speakers, refer to "Presence speaker
connection" in the Owner's Manual.
• This unit can connect speakers that support Bi-amp connection for front
speakers. Refer to "Bi-amp connection" in the Owner's Manual.
Connecting the banana plug
Tighten the knob, and then insert the banana plug
into the end of the terminal.
Banana plug
2
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than half).
Crossover frequency (if available): Set to maximum.
VOLUME
MIN
Subwoofer examples
- 3 -
F R
O N
T
CROSSOVER/
HIGH CUT
MAX MIN MAX