Rohde & Schwarz HAMEG OITek HZO51 English Manual
Rohde & Schwarz HAMEG OITek HZO51 English Manual

Rohde & Schwarz HAMEG OITek HZO51 English Manual

Ac/dc current probe
Hide thumbs Also See for HAMEG OITek HZO51:

Advertisement

Quick Links

V202503
AC/DC Current Probe
Oscilloscopes
HZO51
Spectrum Analyzer
Manual
English
Power Supplies
Modular System
Series 8000
Programmable Instruments
Series 8100
authorized dealer
w w w . h a m e g . c o m
HAMEG Instruments GmbH
Industriestraße 6
D-63533 Mainhausen
Tel +49 (0) 61 82 800-0
Fax +49 (0) 61 82 800-100

Änderungen vorbehalten
sales@hameg.de
北京海洋兴业科技股份有限公司(股票代码:839145) | 电话:010-62178811 传真:010-62176619 | 网址:www.hyxyyq.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HAMEG OITek HZO51 and is the answer not in the manual?

Questions and answers

Summary of Contents for Rohde & Schwarz HAMEG OITek HZO51

  • Page 1 V202503 AC/DC Current Probe Oscilloscopes HZO51 Spectrum Analyzer Manual English Power Supplies Modular System Series 8000 Programmable Instruments Series 8100 authorized dealer w w w . h a m e g . c o m ut notice HAMEG Instruments GmbH GmbH Industriestraße 6 mpany...
  • Page 2: Table Of Contents

    Content Deutsch Français Español English Introduction Safety Specifications HZO5 Operating Instructions 4. Switch On 4. Zero Adjustment 4. Current Measurement 4.4 Auto Power OFF 4.5 Battery Replacement 4.6 Maintenance Warranty and Repair Subject to change without notice 北京海洋兴业科技股份有限公司(股票代码:839145) | 电话:010-62178811 传真:010-62176619 | 网址:www.hyxyyq.com...
  • Page 3: Introduction 4

    ® i30s/i30 ® 1 Introduction i30s/i30 AC/DC Current Clamps The HZO5 current probe has been designed for use with multimeters and oscilloscopes respectively for accurate, Instruction Sheet AC/DC Current Clamps non-intrusive measurement of AC, DC and complex wave- form currents. Introduction Instruction Sheet The i30s AC/DC Current Clamp has been designed for use with...
  • Page 4 – Do not use the product if damaged. Always connect pro- be to display device before it is installed around the con- ductor. – Always ensure the probe is removed from any live elec- tric circuit, and leads are disconnected before removing the battery cover.
  • Page 5 Safety Standards EN 600-:00 EN 600--0:00 EN 600-0:00 00 V Cat III, Pollution Degree  EMC Standards EN 66--:006 ROHS and WEEE compliant This product is designed to be safe under the following con- ditions: – indoor use – altitude up to 000 m –...
  • Page 6: Specifications Hzo5 7

    3 Specifications HZO51 Electrical Characteristics (all accuracies stated at °C ±°C) Nominal current In 000 AC or DC Measuring range 00 / 000 A Overload capacity  00 A Overall DC accuracy ±% of reading ±0. / 0.5 A Resolution ±00 / ±500 mA Typical output noise level 600 µV / 0µV...
  • Page 7: Operating Instructions 8

    4 Operating Instructions Figure   Jaws 6 Jaw trigger  Conventional current 7 ON/OFF direction and range switch  Tactile Barrier 8 Auto zero button 4 Battery cover 9 LED 5 Battery cover screw Warning To avoid injury, when using the probe ensure that your fingers are behind the protective barrier as shown in Figure 1.
  • Page 8: Switch

    (CP1000) 2 m long coax terminated with a safety BNC connector Typical performance Plots 50 Ohms (CP 1005) CP1005 Frequency Response Gain dB 1000A Gain dB 100A 1000 10000 100000 -0.5 -1.5 -2.5 Frequency (Hz) CP1005 Phase Response phase 100A phase 1000A 0.00 1000...
  • Page 9: Current Measurement 0

    the required measuring range and to null the output voltage depress the Auto Zero button. Ensure that the probe is away from the current carrying conductor whilst the probe is being nulled. 4.3 Current Measurement – Switch on the probe by selecting the required measuring range and check that the green LED is lit.
  • Page 10: Maintenance

    body as shown in Fig . Replace the battery and re-fit the battery cover and fasten the screw . Note: Replacement with other than the specified type of battery will invalidate the warranty. Fit only the type 9 V PP3 Alkaline (MN 1604). STOP 4.6 Maintenance Clean the case periodically by wiping it with a damp cloth and...

Table of Contents