Function Settings - Kenwood KDC-348U Instruction Manual

Function settings

1 Press SRC to select a source other than "STANDBY".
Press the volume knob to enter [FUNCTION] mode.
2
Turn the volume knob to select [AUDIO CONTROL] or [SETTINGS], then press to enter.
3
Turn the volume knob to make a selection, then press to confirm.
4
■
See table below for selection.
■
Repeat step 3 until the desired item is selected/activated.
■
Press to return to the previous item.
Hold to finish the procedure.
5
[AUDIO CONTROL] : While listening to any source except in STANDBY state or Bluetooth mode.
Item
SUB-W LEVEL –15 — 0 * — +15: Adjusts the subwoofer output level.
BASS BOOST B.BOOST LV1 */ B.BOOST LV2: Selects your preferred bass boost level. ; OFF: Cancels.
SYSTEM Q NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME: Selects a preset sound mode suitable to the
music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)
BASS ADJUST KDC-X695/ KDC-X395 only:
BASS CTR FRQ 40/ 50/ 60/ 70/ 80/ 100 */ 120/ 150: Selects the center frequency.
BASS LEVEL –8 — 0 * — +8: Adjusts the level.
BASS Q FACTOR 1.00 */ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXTEND ON: Turns on the extended bass. ; OFF *: Cancels.
MID ADJUST KDC-X695/ KDC-X395 only:
MID CTR FRQ 0.5K/ 1.0K/ 1.5K/ 2.0K *: Selects the center frequency.
MID LEVEL –8 — 0 * — +8: Adjusts the level.
MID Q FACTOR 1.00 */ 2.00: Adjusts the quality factor.
TRE ADJUST KDC-X695/ KDC-X395 only:
TRE CTR FRQ 10.0K/ 12.5K */ 15.0K/ 17.5K: Selects the center frequency.
TRE LEVEL –8 — 0 * — +8: Adjusts the level.
BASS LEVEL KDC-BT648U/ KDC-348U only:
–8 — 0 * — +8: Source tone memory: Adjusts the level to memorize in each source. (Before making an
MID LEVEL
adjustment, select the source you want to adjust.)
TRE LEVEL
BALANCE L15 — 0 * — R15: Adjusts the left and right speaker output balance.
FADER R15 — 0 * — F15: Adjusts the rear and front speaker output balance.
SUBWOOFER SET ON *: Turns on the subwoofer output. ; OFF: Cancels.
DETAILED SET
HPF FRONT THROUGH *: All signals are sent to the front speaker. ; 40/60/80/100/ 120/150/180/220 (HZ): Frequencies
lower than the specified value are cut off. (Underlined: KDC-X695/ KDC-X395 only)
HPF REAR THROUGH *: All signals are sent to the rear speaker. ; 40/60/80/100/ 120/150/180/220 (HZ): Frequencies
lower than the specified value are cut off. (Underlined: KDC-X695/ KDC-X395 only)
LPF THROUGH *: All signals are sent to the subwoofer. ; 50/60/80/100/120 (HZ): Frequencies higher than the
SUBWOOFER specified value are cut off. (Underlined: KDC-X695/ KDC-X395 only)
28
English
Selectable setting (Preset: *)