Subsidiary Settings; Mode Set - JVC DR-M100S Instructions Manual

Mode Set

●
Turn on the unit.
●
Turn on the TV and select an input mode such as EXT1.
Various modes of this unit are categorised into menus nested in
2 levels shown in the following table. To change the settings of
these modes, find the desired mode in the menu, then follow the
procedure below. (For details on each menu, see pages 61 - 62)
DVD SET UP
FUNCTION SET UP
INITIAL SET UP
●
The procedure below shows how to set the desired option of the
AAUDIO RECB mode as an example.
1
Press SET UP to access the Main Menu screen.
2
Press selection keys to select AFUNCTION SET UPB, then
press ENTER.
3
Press selection keys to
select ARECORDING
SETB, then press
ENTER.
4
Press selection keys to
select AAUDIO RECB,
then press ENTER.
5
Press selection keys to
select the desired
setting, then press
ENTER.
6
Press SET UP to complete the setting.
Selection Keys
(FGDE)
ENTER
SET UP
AUDIO
LANGUAGE SET (A pg. 21)
AUDIO OUTPUT (A pg. 61)
UTILITY (A pg. 70, 71)
VIDEO IN/OUT (A pg. 22, 58)
RECORDING SET (A pg. 62)
DISPLAY SET (A pg. 62)
OTHERS (A pg. 63)
AUTO CH SET (A pg. 19, 66)
MANUAL CH SET (A pg. 67)
GUIDE PR (A pg. 65)
CLOCK SET (A pg. 69)
DVD SET UP FUNCTION SET UP INITIAL SET UP
VIDEO IN/OUT RECORDING SET DISPLAY SET
SAVE AS LIBRARY ON
XP MODE REC AUDIO DOLBY DIGITAL
AUDIO REC NICAM1/MAIN
NICAM1/MAIN
DIRECT REC
NICAM2/SUB
MONO
SET UP OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
EXIT
* The boldface settings below indicate the settings at your purchase.
AUDIO OUTPUT
DIGITAL AUDIO OUT
8
PCM
/ PCM ONLY
Set to the appropriate mode according to the type of the device
connected to [DIGITAL AUDIO OUT] connector.
DOLBY DIGITAL/PCM
Select this when you connect the digital input connector of a
Dolby Digital Decoder or an amplifier with a built-in Dolby Digital
Decoder.
STREAM/PCM
Select this when you connect the digital input connector of an
amplifier with a built-in DTS, Dolby Digital, or MPEG
multichannel decoder.
PCM ONLY
:
Select this when you connect the linear PCM digital input of
other audio equipment (amplifier, MD or DAT deck, etc.).
NOTE:
If you watch or play back a programme recorded on a DVD-RAM
or DVD-RW (VR mode only) disc which contains multiple audio
languages, select APCM ONLYB in advance and choose main or
sub audio with AUDIO.
ANALOG AUDIO OUT
8
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
STEREO
:
Select this when listening to conventional two-channel stereo
audio with the unit's [AUDIO OUT] connectors connected to a
stereo amplifier/receiver or TV set, or in case you want to
record the audio from a DVD VIDEO disc to a Mini Disc, etc.
DOLBY SURROUND
Select this when listening to audio with the unit's [AUDIO OUT]
connectors connected to an amplifier/receiver with a built-in
surround decoder or a surround decoder.
D. RANGE CONTROL
8
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a
programme encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
NORMAL
:
Normally select this setting to activate this function.
WIDE RANGE
Select this to deactivate this function when you enjoy wide
dynamic range programme.
TV MODE
:
Select this when connecting to a TV. Even soft sound can be
well heard.
NOTES:
●
This function has no effect on programmes other than those
recorded in Dolby Digital format.
●
The effect of ANORMALB and AWIDE RANGEB may not be
OTHERS
different depending on discs.
OUTPUT LEVEL
8
You can lower the output level of analogue audio to accommodate
the unit to the connected A/V equipment.
STANDARD
Normally select this setting.
LOW
:
The output level of analogue audio is lowered.

SUBSIDIARY SETTINGS

DOLBY DIGITAL/PCM /
^
:
:
STEREO
^ / DOLBY SURROUND
:
NORMAL
^
/
:
STANDARD / LOW
^
:
61
EN
STREAM/
WIDE RANGE / TV MODE