Table of Contents
Advertisement
Quick Links
1
Powermatic Scissor 17ft Telescopic Crane
(JB-SCSR-00)
A s s e m b l y M a n u a l
What's In The Box
Please inspect the contents of your shipped package to ensure you have received everything
listed below.
3 x Guide Rods
Weight Rod
Hub Locking Knob
Ronin
2 x Weight Closers
Controller
17ft Powermatic Scissor Jib with
Monitor Arm
Bracket
Gimbal Fluid Head
Jib Controller
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permitted by the applicable copyright
statutes or in writing by the Publisher.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PROAIM JB-SCSR-00
Summary of Contents for PROAIM JB-SCSR-00
- Page 1 Powermatic Scissor 17ft Telescopic Crane (JB-SCSR-00) A s s e m b l y M a n u a l What’s In The Box Please inspect the contents of your shipped package to ensure you have received everything listed below.
- Page 2 BNC Wire HDMI Male to Male Wire 15V AC Adapter Female to Female Connector 3 x T-Type Allen Keys 3/16 “ (2.5mm , 3mm & 4mm) Allen Key Female to Female Connector Wrench 18mm Cable Tie Flight Case...
-
Page 3: Table Of Contents
INDEX Sr. No Particulars Page No. Safety Hints Scissor Telescopic Camera Jib Crane Weight Rod Setup LCD Monitor Arm Setup Gimbal Fluid Head Attaching The Cable Tie Tri-Way Dampener Setup Remove Gimbal fluid Head from Jib’s head Tri-Way Dampener System Assembly Tri-Way Dampener Mounting Gimbal Mounting Balancing Tips... -
Page 4: Safety Hints
Safety Hints ATTENTION: PLEASE READ BEFORE USING TO PREVENT DAMAGE TO THE CRANE! BE HIGHLY VIGILANT WHILE ASSEMBLING Lack of attention while attaching Dolly, Tripod & Crane together can cause substantial damage to equip- ment. BE WATCHFUL OF YOUR HANDS Cautiously operate to avoid pinching your hand/fingers between the arms. -
Page 5: Scissor Telescopic Camera Jib Crane
Scissor Telescopic Crane Setup • Insert the bolt into the hub mounting hole of the Scissor Crane. • Now, secure the bolt using a 18mm wrench. • Place Scissor Jib with the Hub Mounting on top of the Jib Stand. •... -
Page 6: Weight Rod Setup
• Insert the cable guide rod into the boom lock bracket and secure the rod by tightening the bolt. Feature: -Pan Lock enables locking the jib’s pan move- ment for achieving high/low angle shots. -Tilt Lock allows you to fix the jib’s tilt angle to get linear tracking shots. - Page 7 • Loosen the knob of the Jib Controller and slide it into the weight rod. • Tighten the Jib controller's knob to secure it. NOTE: Telescope / Retract the length of Scissor Jib using Jib Controller. • Connect the Jib Controller cable to the 6-pin cable connector (Remote Out).
-
Page 8: Lcd Monitor Arm Setup
LCD Monitor Arm Setup • Connect the Monitor Arm to the Hub Mounting of the jib and tighten it using the provided screws. Feature: The LCD Mounting Arm that attaches to either side of the hub mounting, helps to attach an LCD monitor for better viewing of shots. -
Page 9: Attaching The Cable Tie
• To adjust the tension on the Fluid Head, loosen or tighten the Gimbal Fluid Head's knob per your requirement. • Now, slide the Ronin (Not Included) on the Gimbal Fluid Head and tighten the knob to lock it in its position. NOTE: Without any camera setup this jib gets balanced at 24kg weight. -
Page 10: Tri-Way Dampener Setup
Tri-Way Dampener System Setup Remove Gimbal Fluid head from Jib’s Head • Loosen the knob of the Gimbal Fluid Head and press the push button. • Then, remove the Gimbal fluid head. • Loosen and remove both the screws from the mounting plate using... -
Page 11: Tri-Way Dampener System Assembly
Tri-Way Dampener System Assembly The Proaim Tri-Way Damper is your key to achieving the most creative, stable, and smooth shots possible. It's designed to minimize roll & tilt errors, especially when shooting on moving platforms at varying speeds. • Loosen and remove the bolt using a 4mm Allen key. -
Page 12: Tri-Way Dampener Mounting
Tri-Way Dampener Mounting • Attach the Dampener with the L-plate of the jib’s Head. • Align the holes of the Tri-way Dampener and insert the bolt. • Tighten the bolt securely using a 5/16” Allen key, as shown in the image. •... -
Page 13: Gimbal Mounting
Gimbal Mounting • Loosen the ratchet knob of the Tri way dampener slide Gimbal (Not Included) on it. • After sliding the Gimbal, re-tighten the knob to secure it. • The gimbal is securely attached to the Triway Dampener. • You can set the Left &... -
Page 14: Maintenance
If the camera weight is 2kg, the jib is balanced with 24+7= 31kg If the camera weight is 10kg, the jib is balanced with 24+35= 59kg YOUR PROAIM POWERMATIC SCISSOR 17FT CAMERA JIB CRANE ALL DRESSED UP AND READY TO GO! - Page 15 Warranty: We offer one year warranty for our products from date of purchase. Within this period of time, we will repair it without charge for labor or parts. Warranty doesn’t cover transportation costs nor does it cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspection and evaluation by us.
Need help?
Do you have a question about the JB-SCSR-00 and is the answer not in the manual?
Questions and answers