SGS SC24Q Owner's Manual

24 litre oil-less air compressor

Advertisement

Quick Links

SC24Q 24 LITRE OIL-LESS
AIR COMPRESSOR
OWNER'S MANUAL
FOR YOUR SAFETY
PLEASE READ THESE INSTRUCTIONS CAREFULLY
AND RETAIN THEM FOR FUTURE USE.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SC24Q and is the answer not in the manual?

Questions and answers

Summary of Contents for SGS SC24Q

  • Page 1 SC24Q 24 LITRE OIL-LESS AIR COMPRESSOR OWNER’S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE.
  • Page 2: Safety Guidelines

    fitted with suitable in-line stopped. safety and alarm equipment. 9. Keep fingers away from a running compressor. Fast moving and hot parts will cause injury and/or burns. WWW.SGS-ENGINEERING.COM PAGE 2 PAGE 3...
  • Page 3: Main Technical Data

    WARNING Drain liquid from tank daily. 13. Tanks rust from moisture build-up, which weakens the tank. Make sure Model SC24Q to drain tank regularly and inspect periodically for unsafe conditions Power 0.75kW / 1 HP such as rust formation and corrosion.
  • Page 4: Operation

    Reduce tank pressure below 10 psi, and then drain moisture from tank daily to avoid tank corrosion. Drain moisture from tank by opening the drain valve located underneath the tank. LUBRICATION This is an oilless air compressor and DOES NOT require lubrication to operate. WWW.SGS-ENGINEERING.COM PAGE 6 PAGE 7...
  • Page 5: Break-In Procedure

    In the OFF position, the pressure switch cannot function and the compressor will not operate. Make sure switch is in OFF position when connecting or disconnecting power cord from electrical outlet. WWW.SGS-ENGINEERING.COM PAGE 8 PAGE 9...
  • Page 6: Tank Pressure Gauge

    THERMAL OVERLOAD PROTECTOR CAUTION This compressor is equipped with an automatic reset thermal overload protector, which will shut off motor if it becomes overheated. If thermal overload protector shuts motor OFF frequently, look for the following causes: WWW.SGS-ENGINEERING.COM PAGE 10 PAGE 11...
  • Page 7: Troubleshooting Chart

    3. Replace leaking components or normal/low discharge 4. Broken inlet valves tighten as necessary pressure 5. Piston ring worn 4. Replace compressor valves 5. Replace piston and cylinder WWW.SGS-ENGINEERING.COM PAGE 12 PAGE 13...
  • Page 8: Parts Diagram

    (auto start) Remove and replace check valve Air leaking from Check valve stuck in an open DANGER! Do not disassemble unloader on pressure position check valve with air in tank; bleed switch tank first. WWW.SGS-ENGINEERING.COM PAGE 14 PAGE 15...
  • Page 9 SGS Engineering (UK) Ltd PARTS LIST Unit 1 West Side Park Raynesway Part Part No Part Part No Derby, DE21 7AZ Bolt M5×25 908128 Bolt M4x8 908155 Plain cushion Ø5 908129 O circle Ø13.8 x Ø1.9 908156 EC Declaration of Conformity...
  • Page 10 Specification Table for Tightening Force and Destructive Torque of Screws Scope of application: 1、 The general specification 3-10mm in outer diameter and meets the strength grade of ISO898-1 4.8/8.8; 2、 Screws that are shorter than 3 times in outer diameter are not suitable for the destructive torque tests.
  • Page 11 Standard Component Specification: Min. Tightening Force Description Specification (N.m) Quick connector 1∕4 ≥6 High pressure pipe G3/8 ≥18 ( nut ) Back cover of ≥12 check valve(48) Back cover of ≥15 check valve (55) Note: 1. The fixed head and foot pad screws (M8) shall be controlled according to a strength level of 6.8, and their Min.

Table of Contents