Table of Contents
Advertisement
GEAppliances.com
Cleaning the Radiant Module (continued)
Burned-On
Residue
WARNING:
DAMAGE
to your glass surface
may
occur if you use scrub pads other than BLUE
Scotch-Brite
® Multi-Purpose
No Scratch scrub
pads by 3M.
1. Allow the radiant
module to cool.
2. Spread a few drops
of Cerama Bryte ®to
the entire burned
residue area.
3. Using the Scotch-Brite
®
blue pad, rub the
residue area, applying
pressure
as needed.
Scotch-Brite _ Multi-Purpose
No Scratch blue scrub pad
4. If any residue remains, repeat the steps listed above
as needed.
5. For additional
protection,
after all residue has been
removed,
polish the entire surface with Cerama
Bryte ® and a paper towel.
Heavy, Burned-On
Residue
1. Allow the radiant
module to cool.
2. Spread a few drops of
Cerama Bryte ®to the
entire burned residue
area.
3. Hold the razor scraper
at approximately
a 45 °
angle against the glass
surface and scrape the
soil. It will be necessary
to apply pressure
to the
razor scraper in order to
remove the residue.
4. Keep a small amount of
cream on the residue as
you scrape.
The RAZOR SCRAPER is
available through our Parts
Center. See instructions
under "To Order Parts"
section at right.
NOTE: Razor blade is
packed inverted for safety
reasons. Prior to use, the
blade must be rotated and
reinserted into slot. Do not
use a dull or nicked blade.
5. After scraping
with the razor scraper, use the
Scotch-Brite
®blue pad to remove any remaining
residue.
6. For additional
protection,
after all residue has been
removed,
polish the entire surface with Cerama
Bryte ® and a paper towel.
Metal Marks and Scratches
1. Be careful not to slide pots and pans across your
radiant module. It will leave metal markings
on
the surface.
These marks are removable
using the cleaning
cream with a Scotch-Brite
® blue pad and/or
razor
scraper.
2. If pots with a thin overlay of aluminum
or copper
are allowed to boil dry, the overlay may leave
black discoloration
on the surface.
This should be removed
immediately
before
heating
again or the discoloration
may
be permanent.
WARNING:
Carefully
check the bottom
of
pans for roughness
that would
scratch the
radiant
module.
Glass Surface - Potential for
Permanent Damage
Our testing shows that if you are cooking
high sugar
mixtures such as jelly or fudge
and have a spillovel.
it can cause permanent
damage
to the glass smface
unless the spillover
is immediately
removed.
Damage from Sugary
Spills and Melted Plastic
1. Turn off all surface units. Remove
hot pans.
2. Wearing an oven mitt:
a. Use the razor scraper to move the spill to a cool
area on the radiant module.
b. Remove
the spill with paper towels.
3. Any remaining
spillover
should be left until the
surface has cooled.
4. Don't use the radiant module again until all of the
residue has been completely
removed.
NOTE:
If pitting or indentation
in the glass
surface has already occurred,
the radiant module
glass will have to be replaced.
In this case, service
will be necessary.
To Order Parts
To order Cerama
Bryte ® and the razor scraper, please
call our toll-free number:
National
Parts Center
800.626.2002.
Cerama
Bryte ® Cream
......
# WX 10X300
Razor Scraper
..............
# WXSX1614
Kit .........................
# WB64X5027
(Kit includes
cream and razor scraper)
27
Advertisement
Table of Contents
