Advertisement
Quick Links
JUTM-1834 Servo
DRO
Original:
GB
Operating Instructions
Milling Machine
JPW Tool Group Hong Kong Limited
98 Granville Road, Tsimshatsui East, Kowloon, Hong Kong, PRC
www.jettools.com
Импортёр в РФ: ООО «ИТА Технолоджи»
105082, Москва, Переведеновский пер., д. 17
www.jettools.ru
Made in PRC / Сделано в KHP
M/P– 50000853T
2022-09
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Jet JUTM-1834 Servo DRO
Summary of Contents for Jet JUTM-1834 Servo DRO
- Page 1 JUTM-1834 Servo Milling Machine Original: Operating Instructions JPW Tool Group Hong Kong Limited 98 Granville Road, Tsimshatsui East, Kowloon, Hong Kong, PRC www.jettools.com Импортёр в РФ: ООО «ИТА Технолоджи» 105082, Москва, Переведеновский пер., д. 17 www.jettools.ru Made in PRC / Сделано в KHP M/P–...
- Page 2 Dear Customer, Many thanks for the confidence you have shown in us with the purchase of your new JET-machine. This manual has been prepared for the owner and operators of a JET JUTM-1834 Servo DRO Milling Machine to promote safety during installation, operation and maintenance procedures.
- Page 3 Give your work undivided attention. Use common sense. Do Maintenance and repair work may only be carried out after not operate the machine when you are tired. the machine is protected against accidental starting by pulling the mains plug. Do not operate the machine under the influence of drugs, alcohol or any medication.
- Page 4 complied with the safety standard. the main power on electric cabinet too. 2.2 Requirements to operator and maintenance 2.7 Check, maintenance and service Clarify the fault condition of machine tool according personnel The machine operators should be trained and to the information provided by the operator.
- Page 5 ） Machine tool lifting diagram is as follows: Distance from vertical 75-525 spindle end surface to horizontal worktable Distance from horizontal 1475-625 spindle end surface to horizontal worktable Distance from vertical spindle axis to column 170-620 guide surface Main motor power X-axis feed servo motor torque Y-axis feed servo motor...
- Page 6 screw seat. There is a coolant tank in base cavity; and the coolant pump is equipped on the base. Base parts effect picture: Fig. 3：Base effect picture Fig. 5：Sliding block effect picture 6.2 Bed: The bed is mounted on the base, and securely connected 6.4 Horizontal worktable: through high strength bolts;...
- Page 7 Fig. 8：Ram effect picture 6.7 Vertical milling head: The vertical milling head is mounted on the front end face of ram, inside is equipped with a vertical spindle to realize the vertical milling process. The vertical milling head rotate clockwise or counterclockwise by 45°around the Fig.
- Page 8 2)X-axis drive（see Fig 10，Fig. 11） Gear X-axis drive is shown in block chart 2 in Fig. 10; for transmission parts, see Fig. 11，and the transmission Multi-wedge pulley principle is as follows: X-axis feed motor is the servo motor, together with timing Multi-wedge belt 20-PJ-700 pulley and timing belt are mounted on the left side of vertical...
- Page 9 ball bearing Bearing NJ205E GB/T283 Deep groove 6007-2Z GB/T276 ball bearing Deep groove 6205-2LS GB/T276 ball bearing Deep Cooling System groove 6007-2Z GB/T276 ball Machine coolant tank is installed in the base. And the bearing coolant pump is on the base. The cutting fluid is supplied Deep from coolant pump, through cooling pipe, flows to machine groove...
- Page 10 1. Z-axis electric handwheel; 2, Z-axis lock bolt 3. X-axis electric handwheel; 4. Y-axis electric handwheel; 5. Y-axis lock bolt; 6, Horizontal axis tool unclamp handle; 7. Spindle speed change handle; 8. Sleeve lifting handle; 9. Sleeve locking handle; 10. Operation panel The operation panel is as follows: Fig.
- Page 11 13. Common trouble and trouble shooting Trouble Cause Touble Shooting power while input power is not correct Input the correct power machine starts incorrect connection Connect correctly terminal is loose Press terminals Spindle temperature Bearing damage Replace the bearing rise out of limit Lack of grease Add grease Bearing is too tight...
- Page 12 Certificate of Quality 1 copy Packing List 1 copy 15. Environmental protection Protect the environment. Your appliance contains valuable materials which can be recovered or recycled. Please leave it at a specialized institution. 16. Available accessories Refer to the JET-Price-list...
Need help?
Do you have a question about the JUTM-1834 Servo DRO and is the answer not in the manual?
Questions and answers