Advertisement
Advertisement
Table of Contents
Related Manuals for Ranger design S2-RS36-2
Summary of Contents for Ranger design S2-RS36-2
- Page 1 INSTALLATION GUIDE S2-RS36-2 Shelving steel Ram C/V Box Truck / Trailer...
-
Page 2: Required Items
QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup............................... 3 - 4 q 1.2 Shelf Assembly..........................5 - 6 Phase 2 - Installation q 2.1 Attach Wall Brackets To The End Panels..................q 2.2 Mark Holes For Plus Nuts....................... q 2.3 Attach Plus Nut.......................... -
Page 3: Phase 1 - Assembly
PHASE 1 – ASSEMBLY 1.1 SETUP 1.1.1 Unpack components; compare with the bill of materials. 40 - 716 40 - 715 60 - 13.875 × 36 40 - 7270 40 - 7271 1.1.2 Verify all parts are present. BILL OF MATERIALS Item No. - Page 4 1.1.3 Fastener kits. 94 - 4029 Fastener Kit Fastener Assembly Hex Bolt 8× 8× 8× 8× # 90-204 5/16"-18 × 3/4" GR-5 ZINC #90-204 Hex Bolt 5/16" × 3/4" Screw HWH #98-116 Flat Washer 16× 16× # 92-102 #14 × 1" #94-116 Serrated Nut ZINC Serrated Nut...
-
Page 5: Shelf Assembly
PHASE 1 – ASSEMBLY 1.2 SHELF ASSEMBLY 1.2.1 Attach both panels to the shelf trays. NOTE: You can adjust the bottom shelf location to maximize or minimize your space over the wheel. IMPORTANT: Always handle panels on a smooth, protected and clean surface to avoid unnecessary scratching. 40 - 7270 14"... - Page 6 1.2.2 Attach the bracket head to the bracket arm. NOTE: Hand-tighten the bolts for adjustment. 2× 40 - 715 40 - 716 TOOLS q Cordless Impact q 1/2" Socket HARDWARE USED 4× hand tighten the bolts #90-204 Hex Bolt 5/16" × 3/4" #98-116 Flat Washer #94-116 Serrated Nut S2-RA36-2 Installation Guide | REV.
-
Page 7: Phase 2 - Installation
PHASE 2 – INSTALLATION 2.1 ATTACH WALL BRACKETS TO THE END PANELS 2.1.1 • Lift the assembled shelf to the vehicle with care, then put it in place. • Attach the bracket arm to the panels aligning the brackets head to the structure of the van or truck. IMPORTANT: For Box Trucks and Ram C/V, make sure that the shelving is securely fastened to the structure of the truck or van. - Page 8 PHASE 2 – INSTALLATION 2.2 MARK HOLES FOR PLUS NUTS 2.2.1 After attaching the brackets mark the holes on the brackets and end panels to the structure of the truck or van. Structure of the truck or van. Mark 2 holes of the brackets head on the vehicle horizontal rim.
- Page 9 PHASE 2 – INSTALLATION 2.3 ATTACH PLUS NUTS 2.3.1 • Lift the assembled shelf on the side. • Drill all the marks using 1/2" drill bit w/ drill collar, then attach plus nuts to the holes. NOTE: Use 1/2" drill bit with drill collar to stop drill at 1/2" depth. WARNING: Before drilling, ensure that you will not hit any critical parts of the vehicle like the Gas tank, Wiring Harness and Hose.
- Page 10 2.3.2 How to attach plus nut. • using plusnut gun STEP: Put the plusnut on the plusnut gun, then attach the plus nut in the hole by turning the gun forward until the plus nut locks, then remove the gun by turning in reverse. FORWARD REVERSE •...
- Page 11 PHASE 2 – INSTALLATION 2.4 ATTACH SHELF UNIT TO THE FLOOR 2.4.1 Put the assembled shelf back in place aligning the holes to the plusnuts, then install the end panels to the plus nuts. TOOLS q Cordless Impact q 1/2" Socket HARDWARE USED 4×...
-
Page 12: Attach Wall Brackets
PHASE 2 – INSTALLATION 2.5 ATTACH WALL BRACKETS 2.5.1 Aligned the wall brackets to the plus nuts, then install the wall brackets to the structure of the truck or van. OTE: Tightened the bolts that used to attached the wall bracket to the structure of the truck or van 1 before the bolts that used to attached the wall bracket to the end panel. - Page 13 “You have successfully installed your S2-RS36-2 Thank you for doing business with us.” cs@rangerdesign.com For any feedback or suggestions you may have, please contact: S2-RA36-2 Installation Guide | REV. B1 | Page 13 For technical support, contact us at 1-800-565-5321...
Need help?
Do you have a question about the S2-RS36-2 and is the answer not in the manual?
Questions and answers