Download Print this page

Front Runner SLIMLINE II FATT012 Read Me First

Toyota tundra 3rd gen shorty footrail for over cab camper roof rack kit

Advertisement

Quick Links

front runner
START HERE!
Don't be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
FATT012_REV_A00
Toyota Tundra 3rd Gen Shorty
Footrail for Over Cab Camper
Slimline II Roof Rack kit
READ ME FIRST
IMPORTANT WARNING!
Please call us if you have any questions about the installation of this product.
1
FATT012
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
ENG

Advertisement

loading
Need help?

Need help?

Do you have a question about the SLIMLINE II FATT012 and is the answer not in the manual?

Questions and answers

Summary of Contents for Front Runner SLIMLINE II FATT012

  • Page 1 Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain aspects of your warranty. Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components. A complete kit will contain: 1.
  • Page 2 M8 x 20 Hex Head Bolt M8 x 16 x 1.6 Flat Washer Cordless Denatured M8 Nyloc Nut Driver Alcohol M8 Nut Cap M6 Jack Nut Tool M6 x 30 Button Head Bolt FATT012_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 3 2.2 while holding the Jack Nut Tool, to prevent the Jack Nut from turning. Make sure the Jack Nut is properly pulled up. Cordless Driver FATT012_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 4 This will keep the rack centered. Fully tighten all remaining bolts. Finish off by placing the M8 nut caps over all 13mm the nuts. Tightening Torque: M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb FATT012_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 5 IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.

This manual is also suitable for:

Slimline ii krtt012t