Download Print this page
Front Runner FAJK007 Manual

Front Runner FAJK007 Manual

Inner brackets and foot rail jeep wrangler jku 4 door (2007-current)

Advertisement

Quick Links

START HERE!
Don't be a hero and muscle through this without first reading these fitting instructions! Improper installation of this gear may void certain aspects of
your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
FRONT RUNNER CAN NOT RECOMMEND A MAXIMUM LOAD CARRYING CAPACITY. PLEASE REFER TO YOUR VEHICLE MANUFACTURER'S RECOMMENDATIONS. IT IS CRITICAL
THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN
AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS
TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU
DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE
INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
FAJK007 / FAJK008_REV_A00
inner brackets and Foot Rail
Jeep Wrangler JKU 4 Door (2007-Current)
READ ME FIRST
IMPORTANT WARNING!
1
FAJK007 / FAJK008
© 2020 FRONT RUNNER VEHICLE OUTFITTERS
ENG

Advertisement

loading
Need help?

Need help?

Do you have a question about the FAJK007 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Front Runner FAJK007

  • Page 1 Don’t be a hero and muscle through this without first reading these fitting instructions! Improper installation of this gear may void certain aspects of your warranty. Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components. A complete kit will contain: 1.
  • Page 2: Tools Needed

    M6 x 20 Hex Bolt 20 X M6 Nyloc Nut M6 x 12 x 1SS Flat Washer M8 Cage Nut M8 Large Washer M8 x 75 Hex Bolt Sealing Plug Assembly FIGURE 1.1 FAJK007 / FAJK008_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 3 M8 X 16 Hex Bolt Foot Rail - 1LH + 1RH 14 X M8 x 16 x 1.6SS Flat Washer 14 X M8 Nyloc Nut 14 X M8 Nut Cap FIGURE 1.2 FAJK007 / FAJK008_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 4 Mark the position of the holes in the foot onto the roof. Once the holes have been marked 10mm remove the Rear Support Arms. Drill 4mm pilot holes on the marks you have made. 13mm FAJK007 / FAJK008_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 5 After drilling, clean the area around all the 22mm holes in the roof with a rag and methylated spirits/denatured alcohol. 13mm FAJK007 / FAJK008_REV_C00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 6 Pull back the padding around the roll bar above the rear seats and insert an M8 x 75 Hex Bolt and M8 Large Washer (Items 14 & 15 from FAJK007 box) through the hole as shown. From the inside of the vehicle, in the same position as where you just inserted the bolt in 3.4, push the Middle...
  • Page 7 NOTE: Before fitting the Wind Deflector, insert two M8 x 16 Hex Bolts (Item 16 from FAJK008) or (Item 1 from FAJK007) into the first slat (Combined Slat), using the Machined slots. Slide a bolt to each of the outer corners.
  • Page 8 Leave the Foam Washer and the Aluminum Spacers in place. Screw in the Sealing Plugs reusing the M6 Nyloc Nuts and Washers that held the Foot Rail 13mm in position. FAJK007 / FAJK008_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 9 IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.

This manual is also suitable for:

Fajk008Fajk002Fajk006