Table of Contents
Advertisement
Quick Links
Technical Support and E-Warranty Certificate
www.vevor.com/support
MILL POWER TABLE FEED
MODEL:AL-450
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and does not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
Advertisement
Table of Contents
Related Manuals for VEVOR AL-450
Summary of Contents for VEVOR AL-450
- Page 1 Technical Support and E-Warranty Certificate www.vevor.com/support MILL POWER TABLE FEED MODEL:AL-450 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
- Page 2 This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
-
Page 3: Brief Introduction
BRIEF INTRODUCTION Welcome to use this power feed.It will make your job convenient and make you happy. Please read this manual carefully for your assembly and use of this machine. Suitable for any vertical turret milling machine feeders,including but not limited to Bridgeport, precision Matthews,grizzly,enco,jet,sharp,Webb,GMC, Clark,supermax,turn pro,vectrax,acra,Birmingham,accu,first and more,If you mill with the same installation mode and 5/8"diameter shaft at the... -
Page 4: Specifications
5mm) 277RPM 110V(220V-240 AL-310 0~200 1385mm/min (external 450in-lb V)50/60Hz screw lead 5mm) 277RPM 110V(220V-240 AL-450 0~200 1385mm/min (external 450in-lb V)50/60Hz screw lead 5mm) OPEN THE BOX Project description Quantity Copper gear gasket Install the retainer plate Flat key... - Page 5 Step 3: Slide the inner ring (007) onto the lead screw of the bench, and then slide into the hole of the power feed needle roller bearing. Finally, the inner ring should contact the shoulder of the lead screPlease return to Figure 1(027007) Step 4: Insert the key into the keyway on the lead screw Step 5: Apply graphite base grease to the teeth of the bevel gear (004).
- Page 6 RESTRICTED ASSEMBLY INSTALLATION The power feeder is equipped with a limit switch assembly (051) and a transmission stop assembly (095). It is assembled as follows (please refer to Figure 2): Step 1: Remove the original travel limiter assembly from the workbench and assemble the supplied travel limiter assembly (B18).
-
Page 7: Periodic Maintenance
Step 2: Connect the power cable of the power station to the specific socket Step 3: Turn the switch to the "ON" position, then the optical transmitter (011) should light up Step 4: Turn the control handle (078) from the middle position to one direction, then the table will move in the same direction. - Page 8 BRUSH POSITION Step 1: Remove brush cap (053) (see Figure 4). Then the brush (050) may pop up. Don't let go of the brush. If the brush does not pop, gently remove it with the tip of a screwdriver. Step 2: Check the concave of the brush. The surface should be smooth and clean.
-
Page 9: Parts List
PARTS LIST - 8 -... - Page 10 - 9 -...
- Page 11 - 10 -...
- Page 12 - 11 -...
-
Page 13: Troubleshooting
TROUBLESHOOTING problem Causes and solutions 1.The power supply or cable connection is faulty 2.The circuit breaker is damaged The light emitter does 3.Switch(034)is not in the"On"position or is not emit light damaged. 4.If the motor can be moved,the optical transmitter is damaged 1.The motor rotates when the fast button (012)is pressed... -
Page 14: Circuit Diagram
CIRCUIT DIAGRAM - 13 -... - Page 15 INSTRUCTIONS FOR INSTALLING CROSS FEEDS Transverse stroke lead screws should not be modified for ideal installation INSTALL T-SLOTS FOR TRANSVERSE FEED - 14 -...
- Page 16 HOW TO INSTALL KNEE LIFT FEED Remove the hand crank, dial, dial bearing flange and ·..· Etc. Mounting extension shaft Important Matters: (1) The shaft end must be close to the bearing inner ring (2) The inner shaft is 16 or 18 thread unc.
- Page 17 After step (4) is completed, remove the bevel gear, then install the key, replace the gear, install the dial, tighten the dial nut (add a few small pieces of dial grinding gear). Pack the gear with grease before installing it (do not use silicone grease).
- Page 18 INSTALL T - RAIL LIFT FEED ASSEMBLY - LIMIT ASSEMBLY INSTRUCTIONS - 17 -...
- Page 19 LONGITUDINAL FEED - HORIZONTAL ARRANGEMENT assembly 1. Move the catwalk to the far left 2. Remove the hand crank, dial and bearing flange from the runway. 3. If necessary, install extension shaft for T-table and assemble drive gear. 4. Remove the two screws (M8 x 25) from the small adapter. 5.
- Page 20 Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the AL-450 and is the answer not in the manual?
Questions and answers