Table of Contents
Advertisement
Quick Links
PSoC
6 CY8CPROTO-063-BLE with AIROC
™
®
Bluetooth
LE Prototyping Board user guide
About this document
Scope and purpose
Thank you for your interest in the CY8CPROTO-063-BLE PSoC
The CY8CPROTO-063-BLE PSoC
inexpensive prototyping platform. The CY8CPROTO-063-BLE Prototyping Board includes the AIROC
CYBLE-416045-02 Bluetooth
applications at a very low cost.
In addition, the board includes the following features:
•
Two LEDs to provide feedback
•
A push button to provide a simple user input
•
Footprint for external ECO (2.0 mm × 1.6 mm, 24 MHz)
•
External WCO (32.768 kHz)
•
1.8 V to 3.3 V operation
Intended audience
This document is intended for users interested in the PSoC
Evaluation board
This board is to be used during the design-in process for evaluating and measuring characteristic curves, and
for checking datasheet specifications.
Note:
PCB and auxiliary circuits are NOT optimized for final customer design.
User guide
Please read the sections "Important notice" and "Warnings" at the end of this document
www.infineon.com
®
6 Bluetooth
LE Prototyping Board is designed as an easy-to-use and
™
®
LE module, delivering a complete system solution for a wide range of embedded
®
6 Bluetooth
LE Prototyping Board.
™
®
6 Bluetooth
LE Prototyping Board.
™
™
™
002-24993 Rev. *B
2024-09-27
Advertisement
Table of Contents
Related Manuals for Infineon CY8CPROTO-063-BLE
Summary of Contents for Infineon CY8CPROTO-063-BLE
-
Page 1: About This Document
The CY8CPROTO-063-BLE PSoC 6 Bluetooth LE Prototyping Board is designed as an easy-to-use and ™ inexpensive prototyping platform. The CY8CPROTO-063-BLE Prototyping Board includes the AIROC ™ ® CYBLE-416045-02 Bluetooth LE module, delivering a complete system solution for a wide range of embedded applications at a very low cost. -
Page 2: Important Notice
Boards provided by Infineon Technologies. The design of the Evaluation Boards and Reference Boards has been tested by Infineon Technologies only as described in this document. The design is not qualified in terms of safety requirements, manufacturing and operation over the entire operating temperature range or lifetime. -
Page 3: Safety Precautions
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide Safety precautions Safety precautions Note: Please note the following warnings regarding the hazards associated with development systems. Table 1 Safety precautions Caution: The evaluation or reference board contains parts and assemblies sensitive to electrostatic discharge (ESD). -
Page 4: Table Of Contents
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide Table of contents Table of contents About this document ..............1 Important notice . - Page 5 ® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide Table of contents A.2.5 Header connections ..............24 A.2.5.1...
-
Page 6: Introduction
6 MCU into your end-system. ™ ® The CY8CPROTO-063-BLE PSoC 6 Bluetooth LE Prototyping Board also integrates Infineon KitProg3 that ™ enables onboard programming, debugging, and bridging functionalities, such as USB-UART and USB-I2C. ® KitProg3 is used to program and debug the target PSoC... -
Page 7: Modustoolbox
® core 5.4 host protocol stack. ™ ® The stack is hosted as a library on Infineon’s GitHub. The stack library includes both Bluetooth BR/EDR and Bluetooth ® Low Energy hosts and provides APIs for them. The application can choose to use Bluetooth ®... -
Page 8: Create A New Modustoolbox ™ Application
Select PSoC 63 MCU-based target hardware ™ ModusToolbox presents the list of Infineon kits to start your application development. In this case, we want to ™ develop an application on the CY8CPROTO-063-BLE evaluation board that uses the PSoC 63-line device. Select ™... -
Page 9: Create The Bluetooth ® Le Find Me Code Example
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide 2 ModusToolbox ™ Figure 5 Choose target hardware ® 2.1.1.4 Create the Bluetooth LE Find Me code example (applicable only for the “Using CE directly” flow) Here, you Create an existing code example into Eclipse IDE for ModusToolbox . -
Page 10: Select A Starter Application And Create The Application
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide 2 ModusToolbox ™ ® Figure 6 Create Bluetooth LE Find Me code example You have successfully created a new ModusToolbox application for CY8CPROTO-063-BLE. ™ 2.1.1.5 Select a starter application and create the application (Applicable only for “Working from Scratch”... -
Page 11: Programming And Debugging Using Modustoolbox
. In the project explorer, select the <App Name> ™ project. In the Quick Panel, scroll to the Launches section, and click the <App Name> Program (KitProg3_MiniProg4) configuration as shown in Figure Figure 8 Programming the CY8CPROTO-063-BLE device using ModusToolbox ™ User guide 002-24993 Rev. *B 2024-09-27... -
Page 12: Related Code Examples
™ ™ guide. This is a comprehensive guide for creating, building, and programming ModusToolbox applications ™ Getting started ® This guide will help you get acquainted with the CY8CPROTO-063-BLE PSoC 6 Bluetooth LE Prototyping ™ Board: ® • Kit operation... -
Page 13: Technical Support
™ MiniProg4 device provides an interface for flash programming and debug Note: MiniProg4 is not required to use kits such as CY8CPROTO-063-BLE that have KitProg3 provided on-board • Knowledge Base Articles (KBA): Provide design and application tips from experts on using the device •... -
Page 14: Kit Operation
™ Prototyping Board user guide 3 Kit operation Kit operation ® This chapter introduces you to different features of the CY8CPROTO-063-BLE PSoC 6 Bluetooth LE Prototyping ™ Kit. This primarily includes the programming and debugging functionalities, KitProg3 USB-UART and USB-I2C bridges, and the procedure to update the KitProg3 firmware. -
Page 15: Usb-Uart Bridge
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide 3 Kit operation • ECO Crystal footprint: A footprint for an external crystal is provided so that you may attach a crystal with your choice of frequency. -
Page 16: Usb-I2C Bridge
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide 3 Kit operation KitProg3 PSoC™ 6 P12[6] P5[0] P12[7] P5[1] ® Figure 10 UART Connection between KitProg3 and Bluetooth LE module USB-I2C Bridge KitProg3 can function as a USB-I2C bridge and communicate with the software utility Bridge Control Panel ®... -
Page 17: Code Examples
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide 4 Code examples Code examples This chapter explains the code example to be adapted to the PSoC 6 Prototyping Board. Most existing PSoC ™ ™ MCU code examples only require the device to be changed and GPIOs to be reassigned to match the board. -
Page 18: A Appendix
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Appendix Board details ® The PSoC 6 Bluetooth LE Prototyping Board consists of the following blocks: ™ ® • Bluetooth LE module (CYBLE-416045-02) • PSoC 6 MCU I/O headers J1 and J2 ™... - Page 19 ® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Figure 12 PSoC 6 Bluetooth ® LE Prototyping Board pin details ™ User guide 002-24993 Rev. *B 2024-09-27...
-
Page 20: Hardware Details
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Hardware details A.2.1 Target board ® The target board uses the AIROC CYBLE-416045-02 Bluetooth LE module, which contains a PSoC 6 MCU, ™ ™ CY8C6347BZI-BLD53. PSoC 6 MCU is a scalable and reconfigurable platform architecture for a family of ™... -
Page 21: Kitprog3 Board
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix A.2.2 KitProg3 board A PSoC 5LP device on the KitProg3 board is used to program and debug the target PSoC 6 MCU. The PSoC ™ ™... -
Page 22: Optional Psoc ™ 6 Mcu Voltage Regulator
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Figure 15 Target power supply A.2.3.1 Optional PSoC 6 MCU voltage regulator ™ If the PSoC 6 MCU section of the board is disconnected from the KitProg3 side by breaking the board between ™... -
Page 23: Measure Bluetooth ® Le Module Current Consumption
LE Prototyping Board is broken into two, the two halves can be reconnected for ™ programming and debugging by adding connectors at J5 and J6. Also, a Infineon MiniProg4 device can be connected to a connector at J5 to perform programming and debug. -
Page 24: Header Connections
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Caution: Once the boards are separated, direct UART and I2C connections between the ® Bluetooth LE module and KitProg3 are lost. This is because the traces connecting the UART and I2C lines are cut off during the separation. - Page 25 ® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Figure 18 J1 and J2 headers Table 3 Pin Details of J1 and J2 headers ® ® PSoC 6 Bluetooth LE Prototyping Board GPIO header (J2) PSoC...
-
Page 26: Functionality Of J4 And J5 Headers
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Table 3 (continued) Pin Details of J1 and J2 headers ® ® PSoC 6 Bluetooth LE Prototyping Board GPIO header (J2) PSoC 6 Bluetooth LE Prototyping Board ™... -
Page 27: Functionality Of J6 And J7 Headers (Kitprog3)
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Table 4 Pin Details of J4 and J5 headers KitProg3 header (J4) PSoC 6 MCU header (J5) ™ Signal Description Signal Description J4_1 VTARG Power J5_1... -
Page 28: Le Prototyping Board Features
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Table 5 Pin Details of J6 and J7 Headers PSoC 5LP KitProg3 Header (J6) PSoC 5LP KitProg3 Header (J7) ™ ™ Signal Description Signal Description J6_01... -
Page 29: User Button
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix ® Figure 21 PSoC 6 Bluetooth LE Prototyping Board features ™ A.2.6.1 User button The target PSoC 6 MCU board contains a button connected to the P0.4 pin on the PSoC 6 MCU. -
Page 30: User Leds
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Figure 22 User button on the board A.2.6.2 User LEDs There are two user LEDs on the board connected to pins P6.3 (red) and P7.1 (green) to allow the user to indicate an event or mode. -
Page 31: Capacitors
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix A.2.6.4 CAPSENSE capacitors ™ There are footprints for three CAPSENSE capacitors - one for self-capacitance and one for mutual Capacitance ™ sensing modes, but only the CMOD capacitor used for self-capacitance mode is loaded. If CAPSENSE is not ™... -
Page 32: Le Module
LE module ® CYBLE-416045-02 is a fully certified and qualified module supporting Bluetooth Low Energy wireless communication. CYBLE-416045-02 is a turnkey solution and includes onboard crystal oscillators, trace antenna, passive components, and the Infineon PSoC 6 MCU. ™ ® The Bluetooth LE module is a scalable and reconfigurable platform architecture. - Page 33 PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide A Appendix Figure 26 Connecting the CY8CPROTO-063-BLE to a MiniProg4 Note: CY8CKIT-005-A MiniProg4 is not part of the PSoC 6 Bluetooth ® LE Prototyping Board contents and can ™...
-
Page 34: Acronyms
® PSoC 6 CY8CPROTO-063-BLE with AIROC Bluetooth ™ ™ Prototyping Board user guide Acronyms Acronyms Table 7 Acronyms Used in this Document Acronym Definition Analog-to-Digital Converter Bridge Control Panel ® Bluetooth Low Energy Bill of Materials Code Example Modulator Capacitor... -
Page 35: Revision History
Updated CYBLE-416045-02 EZ-BLE Creator Module to AIROC ™ ® CYBLE-416045-02 Bluetooth LE module ® Updated EZ-BLE Module to Bluetooth LE module Updated all diagrams to Infineon branding Updated CapSense to CAPSENSE ™ Updated KitProg2 to KitProg3 Updated MiniProg3 to MiniProg4 Added About this document section... - Page 36 ™ ™ Prototyping Board user guide Trademarks Trademarks ® The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Infineon is under license. User guide 002-24993 Rev. *B 2024-09-27...
- Page 37 Infineon Technologies, Email: erratum@infineon.com Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be Document reference expected to result in personal injury.
Need help?
Do you have a question about the CY8CPROTO-063-BLE and is the answer not in the manual?
Questions and answers