Directed DIRECTECHS DS4+ MA1 Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. DIRECTECHS DS4+ MA1
  6. Installation manual
Directed DIRECTECHS DS4+ MA1 Installation Manual

Directed DIRECTECHS DS4+ MA1 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
MA1
Designed by Installers for Installers
© 2018 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2018-01-11
DS4+

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DIRECTECHS DS4+ MA1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Directed DIRECTECHS DS4+ MA1

Summary of Contents for Directed DIRECTECHS DS4+ MA1

  • Page 1 INSTALLATION GUIDE Designed by Installers for Installers © 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main harness (H1), 12-pin black connector .................. 6 Relay harness (H2), 10-pin white connector .................. 6 Data harness (H3), 8-pin white connector ..................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    Connection required with manual transmission vehicles. Additional parts required (maximum required): Resistor 100Ω Fuse 7.5A Diode 6A 0 x 1A Diodes 0 x Resistor 0 x Fuse 0 x Relay DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 5: Vehicle Application Guide

    Legend: CC: Comfort & Convenience Controls DL: OE Door Lock & Alarm Controls PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 6: Wiring Connections

    (MUX) Door Lock Output H3/7 Orange/Black Data RX H3/8 Yellow/Black Data TX If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 7: Analog Input/Output Harness (H4), 22-Pin White Connector

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 8: Installation (Wiring Diagrams, Fuse Selection & Vehicle Wiring Reference Charts)

    Junction connector pin 3 Brake Switch (white conn. behind BCM) Relay Block (white conn. at brake switch) (white conn. right of OBDII) It is important to check that the fuses are positioned correctly. DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 9: Vehicle Wiring Reference Chart

    Push button start. White Clutch Gray Clutch switch. White S-Comm White 15 or 16 Behind BCM. White G or H Brake Green Brake switch. White Orange Relay block right of OBDII. White DS4+ MA1 © 2018-01-11 Directed. All rights reserved.
  • Page 10 Solder the wire to secure it on the metal pin. Empty pin Diode This part can be removed because only the metal pin is needed to secure the contact in the empty pin. SComm wire from Directed Digital System DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 11: Type 2

    6 14 driver kick side of the BCM) 7 15 panel) 8 16 It is important to check that the fuses are positioned correctly. Relay Block (white conn. right of OBDII) DS4+ MA1 © 2018-01-11 Directed. All rights reserved.
  • Page 12 BCM above driver kick. White Driver Door Trigger Black/Yellow BCM above driver kick. White Red/Blue Relay block, right of OBDII. White Upper Clutch Black/Yellow Clutch switch. Gray Lower Clutch Black/Yellow Clutch switch. Gray DS4+ MA1 © 2018-01-11 Directed. All rights reserved.
  • Page 13 For vehicle equipped with a manual transmission, do the following connection: Upper (+) Brake Output: White 5 & 11 Clutch Switch (-) Ground (Gray 2-pin Connector) Clutch: Black/Yellow, pin 1 Lower Clutch Switch (-) Ground (White 2-pin Connector) Clutch: Black/Yellow, pin 1 DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 14: Key2Go

    Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO is compatible with XKLoader2, the online web tool, and the DirectLink Mobile application.

  • Page 15: When Used In Conjunction With Smartstart

    SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming of the DirectLink application or via the online web tool. Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor. DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 16: Module Programming

    Key Blade IN Key Bla Press the Push-to-Start (PTS) button again to turn ignition OFF. Key Blade IN Key Blade OUT Remove the second key blade from the key port. Clutch Clutch DS4+ MA1 © 2018-01-11 Directed. All rights reserved.
  • Page 17 Flashes green. Green Key Blade IN Key Blade Press the PTS button again to turn ignition OFF. Press & Release Press and release the brake pedal or clutch pedal (manual transmission). Clutch DS4+ MA1 © 2018-01-11 Directed. All rights reserved.
  • Page 18 By default, the tachometer is preprogrammed for the vehicle. For instructions on how to Initialize tachometer program tach, see page 22. * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 19: Led Diagnostics And Troubleshooting

    External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 DS4+ MA1 © 2018-01-11 Directed. All rights reserved.
  • Page 20 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 21: Soft Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Release Solid DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 22: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature using the DirectLink application for mobile devices to adjust the starter output time in 50mS increments to compensate for such an occurrence. DS4+ MA1 © 2018-01-11 Directed. All rights reserved.

  • Page 23: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 24: Quick Reference Guide

    Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode.
  • Page 25 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

Table of Contents