BETRIEBSANLEITUNG
OPERATING INSTRUCTIONS
SPECK-TRIPLEX-PLUNGERPUMPE
SPECK TRIPLEX PLUNGER PUMP
Leistungsbereich - Performance
Type
Best.-Nr. Leistungs-
Type
Code No.
P81/215-260G 00.6010
P81/215-260G 00.5849
P81/215-260G
--
P81/215-260G
--
Die angegebenen max. Drücke und Drehzahlen gelten für Aussetzbetrieb
mit Kaltwasser.
NPSH erf. ist gültig für Wasser (spez. Gewicht 1kg/dm3, Viskosität
=1°E) bei max. zulässiger Pumpendrehzahl.
Fördermedium: Sauberes Wasser gefiltert, Filtergröße 100µm.
* höhere Wassertemperaturen bei separater Getriebekühlung möglich.
Bitte Rücksprache mit dem Hersteller halten.
Inbetriebnahme und Wartung
Vor Inbetriebnahme Ölstand prüfen und für störungsfreien Wasserzu-
lauf sorgen.
Bei Frostgefahr muss das Wasser aus der Pumpe und den
angrenzenden Anlagenteilen (insbesondere auch das UL-Ventil) entleert
werden. Zum Entleeren kann der zweite, unbenutzte Druckanschluß ver-
wendet werden. Hierzu kann die Pumpe ca. 1-2 Minuten „trocken" laufen.
Ölfüllmenge 16,0 l. Nur Industriegetriebeöl ISO VG 220 (z.B. Aral De-
gol BG220), oder KFZ- Getriebeöl SAE 90 GL4 verwenden. Erster
Ölwechsel nach 50 Betriebsstunden; dann alle 1000 Betriebsstunden,
spätestens 1x jährlich.
Bei Betrieb in feuchten Räumen bzw. bei hohen Tempera-
turschwankungen. Bei Kondenswasserbildung im Getrieberaum (Auf-
schäumen des Öles) sofort Ölwechsel durchführen.
NPSH-Wert beachten.
Getriebe- Ölkühlung:
Der Wasserzulaufdruck bei Nutzung des integrierten
Getriebeöl-Kühlsystems (Standardmäßige Ausführung) darf 2bar nicht
überschreiten.
Bei separatem Getriebeöl-Kühlkreislauf (maximaler Druck 2bar) kann
der pumpen-saugseitige Wasserzulaufdruck bis max. 10bar betragen.
Darauf achten, dass die Saugpulsation ausreichend gedämpft wird –
Resonanz der starren Wassersäule muss unbedingt vermieden
werden.
Überdruck
Eingangs-
aufnahme
drehzahl
max.
Power
Pressure
Input
Consump.
RPM
max.
kW
bar
min
106
260
1500
106
260
1800
106
260
2200
106
260
2600
Pumpen-
Förder-
Wasser
drehzahl
menge
temp.
max.
max.
max.*
Pump
Output
Water-
RPM
Temp.
max.
max.
max.*
-1
-1
min
l/min
580
213
580
213
580
213
580
213
The stated figures are for max. pressure and max. speed (rpm) and apply
for interval operation with cold water.
Required NPSH refers to water (specific weight 1kg/dm3, viscosity 1°E)
at max. permissible pump revolutions.
Fluid medium: Clean water filtered with 100µm.
* higher temperatures possible with separate crankcase cooling sys-
tem; the manufacturer is to be contacted in this case.
Operation and Maintenance
Check oil level prior to starting and ensure trouble-free water supply.
If there is a danger of frost, the water in the pump and
in the pump fittings (particularly the unloader valve) must be emptied.
The second discharge port can also be used and the pump run "dry" for
1-2 minutes for this purpose.
Oil amount: 16,0 litres. Only use ISO VG 220 industrial gear oil (e.g.
Aral Degol BG220) or automobile gear oil SAE 90 GL4. Initial change
after 50 operating hours and then every 1000 operating hours after one
year latest.
when operating in damp places or with high tempera-
ture fluctuations. Oil must be changed immediately should condensate
(frothy oil) occur in the gear box.
NPSH values must be observed.
Cooling the Gear Oil
The water input pressure must not exceed 2 bar when
using the integrated system for cooling the gear oil (standard version).
If a separate cooling circuit (max. 2 bar) is installed, it is then possible
to have an input pressure of up to max. 10 bar on the suction side of
the pump.
Make sure that suction pulsation is sufficiently dampened – water col-
umn resonance must be avoided.
P81/215-260G
Plunger
Hub
Gewicht
-Ø
Plunger
Stroke Weight
dia.
approx.
°C
mm
mm
30
48
72
348
30
48
72
348
30
48
72
348
30
48
72
348
NPSHR
ca.
NPSH
Required
kg
mWs
--
--
--
--
D1777 1017S
Need help?
Do you have a question about the P81/215-260G and is the answer not in the manual?
Questions and answers