Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Amylior aceKare Yomper+ Mounting bracket for foldable frame wheelchairs
Summary of Contents for Amylior aceKare Yomper+ Mounting bracket for foldable frame wheelchairs
- Page 1 Installation of the mounting bracket for foldable frame wheelchairs...
-
Page 2: Table Of Contents
Choice of the drawbar position A . Position verification page 3 B . Position change page 4 Installation of left side A . Installation on the wheel axle page 5 B . Height adjustment and tightening page 7 C . Positioning the clamp page 8 Installation of right side... - Page 3 BEFORE STARTING TO ASSEMBLE THE BRACKET • Installation of the Yomper must be done by a healthcare profes- sional and not by the user. • The work surface must be perfectly level and clean. • The wheelchair must be fully unfolded and locked. •...
-
Page 4: Position Verification
Choice of the drawbar position Position verification The default setting is position 1, which is its most frequent position. The following is how to check its position before starting bracket assembly, and how to change it if necessary. The different positions are to avoid the Yomper from colliding with the wheelchair’s folding system. -
Page 5: Position Change
Position change Indexing Plunger If the position needs to be changed, the indexing plunger needs to be removed. To move screw , the indexing finger plunger must be removed. When reassembling, allow 0.8 in (2 mm) to protrude from screw thread Then tighten nut to maintain your setting. -
Page 6: Installation Of The Left Side
Installation of the left side Installation on the wheel axle. • Make sure that the > 0.15’’ (4 mm) > 0.15’’ (4 mm) wheelchair is correctly unfolded and that the work surface is perfectly horizontal. • Check that the available sleeve length is >... - Page 7 Insert or move (doubles) spacers to ensure that the side mounting plate clears all obstacles. Screw the socket nut loosely.
-
Page 8: Height Adjustment And Tightening
Height adjustment and tightening Install the bubble level on the bracket and rotate until the bubble is perfectly centered. Tighten the nut to keep this setting. -
Page 9: Positioning The Clamp
Positioning the clamp. Install the clamp on the tube Slide the clamp on the tube without tightening the screws. until one of the holes is aligned with one of the grooves. If the clamp is too far, see special case N ° 3 on page 13. Fill the gap between the clamp and the bracket with spacers, if necessary. -
Page 10: Installation Of The Right Side
Installation of the right side Installation on the wheel axle. Refer to pages 5-6 and repeat the same steps for the right side. Height adjustment and tightening. Refer to page 7 and repeat the same steps for the right side. Positioning the clamp Refer to page 8 and repeat the same... -
Page 11: Adjustment Of The Central Part
Adjustment of the central part Width adjustment. • To adjust length, loosen all eight grub screws. • Apply medium strength threadlocker to screws. • Adjust length. • Lock the bar. • Adjust the symmetry. • Lightly tighten the 4 grub screws under the sliding bracket ( 1 ). •... -
Page 12: Height Control
Height control. Check the height of the bar : 7½’’ (190 mm) from the ground. (Tolerance: 7½’’ to 8¼’’ (190 mm to 210 mm) 7½’’ to 8¼’’ (190 mm to 210 mm) If the height of the bar is not within tolerance, adjust the settings by loosening the clamp screws and the socket nut. -
Page 13: Before Use
Before use Verify that the Yomper is properly attached and the support bar is secured solidly. Special case n° 1 If the available sleeve length is < (0.15’’ (4 mm) Remove a spacer (or two) to obtain the desired length. - Page 14 Special case n° 2 If the ring is not properly placed or risks being warped when tightening Add a spacer. Special case n° 3 If the clamp is too far from one of the groove Use the extender. Always put two screws in the groove.
- Page 15 Before using the Yomper Check the adjustment of the Yomper stopper. The stopper prevents the Yomper from tipping the wheelchair backwards. The Yomper stopper and the mounting bracket stopper must connect when the front wheels of the chair are raised 4¾ in (120 mm).
- Page 16 Distributed by : 3190 F.-X.-Tessier Vaudreuil-Dorion QC J7V 5V5, CANADA www.amylior.com Manufactured by : SARL Acekare 7 rue de Mireport 33310 LORMONT, France www.acekare.com This medical device is a regulated healthcare product and, in compliance with these regulations, bears the CE mark.
Need help?
Do you have a question about the aceKare Yomper+ Mounting bracket for foldable frame wheelchairs and is the answer not in the manual?
Questions and answers