Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Holzstar TKS 316 PRO
Summary of Contents for Holzstar TKS 316 PRO
- Page 1 Instruction Manual Table Saw TKS 316 PRO 230 V TKS 316 PRO 400 V TKS 316 PRO...
-
Page 2: Table Of Contents
Passing on as well as copying of this document, the use 15 EC-Declaration of Conformity .... 27 and distribution of its content are prohibited if not explic- itly permitted. Contraventions are liable to compensa- tion. Subject to technical modifications and error. TKS 316 PRO | Version 1.07... -
Page 3: Introduction
This combination of symbol and signal term indica- knowledge gained from using the application, whichthen tes a directly dangerous situation which may cause could be shared and be valuable to develop ourproducts death or serious injury if not averted. even further. TKS 316 PRO | Version 1.07... -
Page 4: Tips And Recommendations
TKS 316 PRO | Version 1.07... -
Page 5: Requirements To Staff
Certain works may only be performed by specialist per- drugs, alcohol or medication. sonnel of the manufacturer. Other personnel is not au- thorized to perform these works. Please contact our cus- tomer service for the execution of all arising work. TKS 316 PRO | Version 1.07... -
Page 6: Safety Labels On The Table Saw
- Always work with a properly set splitting knife. - Cut thin or thin-walled workpieces only with fine- toothed saw blades. Always use sharp saw blades. TKS 316 PRO | Version 1.07... -
Page 7: Intended Use
Intended Use Intended Use The Table Saw TKS 316 PRO is intended for longitudinal and transverse cutting of solid wood, coated wood, chip- board, blockboard and similar wooden materials. Round workpieces may only be sawn with a suitable holding fix- ture as they can be rotated by the rotating saw blade. -
Page 8: Residual Risks
800 mm Work height 850 mm 850 mm Drive motor output 1,6 kW 2,1 kW Absorbed power 2,2 kW 2,8 kW drive motor 5.1 Type plate Fig. 4: Type plate TKS 316 PRO (230 V) TKS 316 PRO | Version 1.07... -
Page 9: Transport, Packaging, Storage
The device may be lifted unsecured by a maximum of 2cm. Employees must be outside the danger zone, the reach of loads. Warn employees and, if necessary, advise employ- ees of the hazard. TKS 316 PRO | Version 1.07... -
Page 10: Description Of The Device
- There must be sufficient space for the operating personnel, for material transport and for adjust- ment and maintenance work. Fig. 5: Table Saw TKS 316 PRO - The place of installation must have good lighting. 1. Suction hose - There must be an extraction device with min. 690 m3/h extraction capacity, min. - Page 11 Fig. 10: Mounting On / Off - Switch NOTE! The switch must be mounted on the left stand. Step 7: Mount the transport rollers as well as the trans- port handles to the machine. Fig. 7: Folding out the feet TKS 316 PRO | Version 1.07...
-
Page 12: Sliding Rail
Check whether the sliding carriage is stopped by the end stop screw. Front mounting bracket Step 11: Screw the hexagon bolt into the sliding carriage from below. Fig. 13: Mounting mounting bracket TKS 316 PRO | Version 1.07... - Page 13 With spacers, the position of the saw blade is adju- sted to the riving knife. The position of the saw blade has been determined at the factory. One or more spacers are already on the motor shaft. TKS 316 PRO | Version 1.07...
- Page 14 (Otherwise, the splitting wedge can no longer be locked. CAUTION! Fig. 19: Mounting riving knife part 1 Risk of cutting on the saw blade. Wear safety gloves. Use protective gloves! TKS 316 PRO | Version 1.07...
- Page 15 Step 2: Attach the table extension (Pos.200) to the back of the table. Step 3: Insert the screw (Pos.203) into the hole from the outside. Step 4: Mount the wing nut M6 (pos.204) on the screw (pos.203) and tighten it slightly. TKS 316 PRO | Version 1.07...
-
Page 16: Electrical Connection
Only use the table saw in a dry environment. Operate the table saw only on an electrical supply that meets the following requi- rements: TKS 316 PRO | Version 1.07... -
Page 17: Operation Of The Table Saw
- outdoors. CAUTION! - when only few chips are produced with narrow work- Danger of crushing! piece thicknesses. Improper work on the machine may result in injury to - with dust mask. the upper limbs TKS 316 PRO | Version 1.07... -
Page 18: Adjusting The Cutting Height
Adjust the cutting height by turning the hand- wheel. Wear a Dust mask in dust genera- ting work! Wear safety shoes! Handwheel for Wear protective clothing! cutting height adjustment Fig. 29: Adjusting the cutting height TKS 316 PRO | Version 1.07... -
Page 19: Adjusting The Saw Blade Angle Of Inclination
Step 5: Switch off the table saw if you do not continue wor- king immediately. In order to use the full adjustment range of 45°, the cutting height must be reduced accordingly. - For sawing thick workpieces. - For sawing thin workpieces with swiveled saw blade. TKS 316 PRO | Version 1.07... -
Page 20: Care, Maintenance And Repair
Step 5: Check the machine for damage to the safety de- vices and the saw blade. If necessary, carry out or arrange for the repair to be carried out in ac- cordance with the safety instructions. TKS 316 PRO | Version 1.07... -
Page 21: Saw Blade Change
There is also a risk of cuts on the stationary saw blade. Wear protective gloves. When reassembling, always pay attention to the direction of rotation and the arrangement of the flan- ges. Fig. 33: Saw blade change Use protective gloves! TKS 316 PRO | Version 1.07... -
Page 22: Troubleshooting
Step 3: Guide the machine components and operating materials to the appropriate disposal routes. 12.2 Disposal of electrical equipment Note that electrical equipment contains a variety of recy- cling-capable materials and also environmentally hazar- dous components. TKS 316 PRO | Version 1.07... -
Page 23: Disposal Via Municipal Collection Points
The symbol on the product or its packaging indi- cates that this product should not be treated as normal The engine for the Table Saw TKS 316 PRO 400V must household waste, but must be returned to a collection be ordered. The engine has the number 68 in the spare point for the recycling of electrical and electronic equip- parts drawing 2. -
Page 24: Spare Parts Drawings
The following spare parts drawings are intended to help identify the necessary spare parts. To order, please send a copy of the list of spare parts with the marked components to your dealer. Spare parts drawing 1 Fig. 34: Spare parts drawing 1 Table Saw TKS 316 PRO TKS 316 PRO | Version 1.07... - Page 25 Spare parts Spare parts drawing 2 Fig. 35: Spare parts drawing 2 - Table Saw TKS 316 PRO Spare parts drawing 3 Fig. 36: Spare parts drawing 3 - Table Saw TKS 316 PRO TKS 316 PRO | Version 1.07...
-
Page 26: Electrical Circuit Diagrams
Electrical circuit diagram TKS 316 PRO (230V) Fig. 37: Electrical circuit diagram TKS 316 PRO 230V Model Electrical circuit diagram TKS 316 PRO (400V) Fig. 38: Electrical circuit diagram TKS 316 PRO 400 V Model TKS 316 PRO | Version 1.07... -
Page 27: Ec-Declaration Of Conformity
≤ 16 A per phase and not subject to conditional connection Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 09.03.2023 ______________________ Kilian Stürmer General Manager TKS 316 PRO | Version 1.07... - Page 28 www.holzstar.de...
Need help?
Do you have a question about the TKS 316 PRO and is the answer not in the manual?
Questions and answers