PAIRING THE REMOTE CONTROL
You must pair the Bed Frame to a Remote Control before operation. Ensure the Bed Frame has been unplugged
for at least 10 seconds, then proceed as follows:
1. Plug the Bed Frame into the mains. This will automatically switch it to Pairing Mode for 30 minutes. In this
time, the Bed Frame will search for Remote Controls to be paired with.
2. During Pairing Mode, press and release any Button. This will pair the Remote Control to the Bed Frame.
UNPAIRING THE REMOTE CONTROL
1. Press and hold the Head UP and Foot DOWN Buttons for at least 10 seconds.
2. The Remote Control will flash 3 times.
3. Test the Remote Control to check that it has been safely unpaired.
REFERENCE DRIVE
Before using the Bed Frame for the first time, you must perform a reference drive.When the drive is initiated,
the lower section of the bed will move first, followed by the upper section.
1. Press and hold the Head UP/DOWN, Foot UP/DOWN or Sleeping Position Button. The lower part of the
Bed Frame will begin the reference drive. It will reach a lower limit and then move up slightly. Do not release
the button.
2. Continuing to hold the button, wait for the upper part of the frame to complete the drive.
3. Release the button and use the Bed Frame according to the instructions.
If the drive is interrupted, pressing any movement button restarts downward movement.
MOVING THE BED FRAME UP AND DOWN
1. Press and hold the UP/DOWN Button for the Platform you wish to adjust
2. Wait until the Bed Frame has reached the desired position
3. Release the UP/DOWN Button
The Bed Frame will move until the Button is released or the highest / lowest position is reached.
SAVING A MEMORY POSITION
There are two pre-saved Memory Positions: Anti-Snore (Position 1) and Zero Gravity (Position 2). Press the
Memory Position Buttons on the Remote Control to move to these positions. You can change saved Memory
Positions to new Memory Positions. To do this, proceed as follows:
1. Press and hold the UP/DOWN Button for the Platform you wish to adjust
2. Wait until the Bed Frame has reached the desired position
3. Release the UP/DOWN Button
4. Press and hold the Button for the new Memory Position for at least 3 seconds to save the
position. The Control Box will click twice to confim.
5. Release the Memory Position Button.
20 // COSMO VIENNA ADJUSTABLE BED FRAME – OWNER'S MANUAL
FACTORY RESET
A Factory Reset restores the Bed Frame to the same state as before first use. Any memory positions you have
stored will be deleted and replaced with the pre-set memory positions. To perform a Factory Reset:
1. Press and hold the Foot DOWN and Head DOWN buttons for 10 seconds.
2. When the reset is complete, the Control Box will click twice.
3. Release the buttons.
To perform a Reference Drive after the Factory Reset, only release one of the DOWN buttons. This will start
the Drive automatically.
MOVING THE BED FRAME TO A SAVED MEMORY POSITION
Proceed as follows to move the Bed Frame to a saved Memory Position:
1. Press the Memory Position Button for the Memory Position you wish to move to, then
release.
2. Wait for the Bed Frame to move to the saved Memory Position
MOVING THE BED FRAME TO THE SLEEPING POSITION
The Sleeping Position is the Bed Frame's lowest position. While in the Sleeping Position, all Platforms are
horizontal. Proceed as follows to move the Bed Frame to the Sleeping Position:
1. Press and release the Sleeping Position Button (do not hold the Button)
2. Wait for the Bed Frame to move to the Sleeping Position
ACTIVATING THE CHILD LOCK
Always activate the Child Lock when children are near the Bed Frame. Proceed as follows:
1. Press and hold the Head UP and Foot UP Buttons for at least 6 seconds.
2. The LED will flash 3 times to confirm. Test the Remote Control to check that Child Lock
has been activated.
To disable Child Lock, repeat the steps above.
If you remove the batteries from the Remote Control, the Child Lock will be deactivated automatically If you try
to operate the Bed Frame while the Child Lock is activated, the LED will flash 6 times.
COSMO VIENNA ADJUSTABLE BED FRAME – OWNER'S MANUAL // 21
Need help?
Do you have a question about the COSMO VIENNA LUXE and is the answer not in the manual?