Page 1
IBG-8 BENCH GRINDER IBG-10 IBG-12 Original: Operating Instructions JPW Tool Group Hong Kong Limited 98 Granville Road, Tsimshatsui East, Kowloon, Hong Kong, PRC www.jettools.com Импортёр в РФ: ООО «ИТА Технолоджи» 105082, Москва, Переведеновский пер., д. 17 www.jettools.ru Made in Taiwan / Сделано на Тайване...
Do not use this bench grinder for other than its 19. Provide for adequate space surrounding work intended use. If used for other purposes, JET area and non-glare, overhead lighting. disclaims any real or implied warranty and holds itself harmless from any injury that may result from 20.
The operator is encouraged to familiarize himself/herself with ANSI B7.1 – Safety Requirements for Use, Care and Protection of Abrasive Wheels. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com.
5.0 Specifications Model ..............IBG-8 ........IBG-10 ........IBG-12 Stock Number ..........578008M ....578010-RU/3RU ......578012-3RU Motor and electricals: Motor type ....................induction ..........Horsepower (true output) ........0.75kW ........1.1kW ........1.5kW Phase .............. single ......single/three ........three Voltage .............
Shipping............31.73 kg ........ 56.60 kg ........74 kg The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.
Chipped or cracked wheels can An optional pedestal stand (not included) is break up and cause serious damage to the available from JET for your grinder. See sect. 12.0. grinder and/or severe injury to the operator. Regularly inspect wheels for damage.
6.5 Assembling eye shield brackets washers (L), through the tool rest (M), into the to spark guards wheel housing. 3. Install the right tool rest in the same manner. Refer to Figure 5. 4. The tool rests should be adjusted to within 1/16” Note: Spark guards (A) and eye shield brackets (D) of the grinding wheel or other accessories being are marked L for left side assembly and R for right...
A Fine Grain Abrasive Grinding Wheel should be 7.0 Electrical connections used for sharpening tools or grinding to close size tolerances because it removes metal more gradually for precision grinding and achieves a smoother finish. 7.1 Grounding instructions 1. All Grounded, Cord-connected Tools: Always use approved safety glasses or face shield while operating grinder.
New wheels sometimes require dressing to make them round. See sect. 10.5. 10.3 Changing Wheels Figure 10: eye shield adjustment The JET Series bench grinders come equipped with Spark Guard 25.4 general purpose grinding wheels. Wheels vary according to types of abrasive, hardness, grit size, As the wheel wears down, the spark guards must be and structure.
3. Remove wheel guard using a cross-point or The operator who takes time to patiently perform needed adjustments will be rewarded by wheels flathead screwdriver. running true, and accurate grinding of work pieces. 4. Stabilize wheel by holding opposite wheel firmly, or placing a wood wedge between wheel and 10.4.1 Adjusting concentricity tool rest.
10.5 Dressing the wheels 10.6 Wire wheel brushes Below is a general procedure for dressing a grinding Wire brushing provides a fast way to remove rust wheel. Always consult wheel dresser scale, burrs, and paint from metal. Use coarse wire manufacturer’s instructions for specific information brushes for hard cleaning jobs.
Replace capacitor. Open circuit in motor or loose Inspect all lead connections on motor for connection. loose or open connections. Motor faulty. Contact JET technical service. Motor will not start; many electrical machines Turn off other machines and try again.
* WARNING: Some corrections may required a qualified electrician. 12.0 Optional accessories These accessory items, purchased separately, are available for your JET bench grinder. Contact your dealer to order, or call JET at the phone number on the cover. 578172 578173...
Page 15
12.1.2 IBG-8 Grinder – Parts List Index No Part No Description Size 1 ....IBG8-01 ..... Truss Head Screw ........... 3/16”-24 x 1/4”....4 2 ....IBG8-02 ..... Rubber Pad....................4 3 ....IBG8-03 ..... Base Plate ..................... 1 4 ....
Page 16
Index No Part No Description Size 54-5 ... IBG8-54-5....Pin................6mm ......1 54-6 ... TS-1503051 ....Socket Head Cap Screw.......... M6 x 20 ......1 54-7 ... IBG8-54-7....Square Nut............... M6 ......... 1 55 ....TS-0680041 ....Flat Washer ............. 3/8” ........ 2 56 ....
Page 18
13.2.2 IBG-10 Grinder – Parts List Index No Part No Description Size 1 ....IBG8-01 ..... Truss Head Screw ........... 3/16”-24 x 1/4”....4 2 ....IBG10-02 ....Rubber Pad....................4 3 ....IBG10-03 ....Base Plate ..................... 1 4 ....
Page 21
13.3.2 IBG-12 Grinder – Parts List Index No Part No Description Size 1 ....IBG8-04 ..... Truss Head Screw ........... 3/16”-24 x 3/8”..... 13 2 ....IBG10-03 ....Base Plate ..................... 1 3 ....IBG10-06 ....Start Capacitor ............400MFD, 125VAC ..1 4 ....
Page 22
Index No Part No Description Size 54-4 ... IBG8-54-4....Cutter Washer....................2 54-5 ... IBG8-54-5....Pin................6mm ......1 54-6 ... TS-1503051 ....Socket Head Cap Screw.......... M6 x 20 ......1 54-7 ... IBG8-54-7....Square Nut............... M6 ......... 1 55 ....
Need help?
Do you have a question about the IBG-8 and is the answer not in the manual?
Questions and answers