Table of Contents
Related Manuals for Jet JAT-464
Summary of Contents for Jet JAT-464
- Page 1 Pneumatic Angle Grinder #505464, JAT-464 #505465, JAT-465 #505467, JAT-467 Operation & Parts Manual M-505464 Edition 1 05/2019 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2019 JET...
-
Page 2: Safety Warnings
15. Excessive air pressure and too much free Do not use this tool for other than its intended rotation may decrease life of the tool and may use. If used for other purposes, JET disclaims cause a hazardous situation. any real or implied warranty and holds itself 16. - Page 3 32. Do not lubricate the tool with combustible Your risk of exposure varies, depending on liquids, such as kerosene, diesel or jet fuel. how often you do this type of work. To reduce 33. Do not dispose of this tool with normal your exposure to these chemicals, work in a household waste.
-
Page 4: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 5: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 6: Setup And Assembly
Disconnect air hose from tool. Place 4 or 5 drops of air tool oil into air inlet. Make sure spindle screw is tight before operating grinder. JAT-464,-465,-467 Pneumatic Angle Grinder ... - Page 7 Tool Pressure Use proper air hose size (refer to tool specifications). The hose should be just long JET Air Tools operate on 70-to-100 psi (pounds enough to serve the working area. Excessive per square inch) air pressure measured at the tool hose length will cause pressure drop.
- Page 8 Use a light oil containing rust inhibitors, such as When its useful life has expired, please leave tool SAE #10. Many JET air tools have integral oil at a specialized facility. reservoirs, which should be kept filled when in-line oilers are not used.
- Page 9 Troubleshooting JAT-464/465/467 Angle Grinders Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
-
Page 10: Replacement Parts
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually. #505464, JAT-464, 4-inch Angle Grinder – exploded view ... - Page 11 #505464, JAT-464, 4-inch Angle Grinder – parts list # Part No. Description # Part No. Description 1 JAT464-01 Housing 43 JAT464-43 Outer Flange 16mm 2 JAT464-02 Inlet Guide 44 JAT464-44 Wheel Lock Bolt M8x21.3L mm 3 JAT464-03 Air Inlet * 45 JAT464-45 Guard 4 in.
- Page 12 #505465, JAT-465, 5-inch Angle Grinder – exploded view JAT-464,-465,-467 Pneumatic Angle Grinder ...
- Page 13 #505465, JAT-465, 5-inch Angle Grinder – parts list # Part No. Description # Part No. Description 1 JAT464-01 Housing 44 JAT464-44 Wheel Lock Bolt M8x21.3L mm 2 JAT464-02 Inlet Guide 45 JAT465-45 Guard 5 in. * 3 JAT464-03 Air Inlet * 46 JAT464-46 Side Handle * 4 JAT464-04...
- Page 14 #505467, JAT-467, 7-inch Angle Grinder – exploded view JAT-464,-465,-467 Pneumatic Angle Grinder ...
- Page 15 #505467, JAT-467, 7-inch Angle Grinder – parts list # Part No. Description # Part No. Description 1 JAT467-01 Housing 43 JAT467-43 Outer Flange 2 JAT467-02 Inlet Guide 44 JAT467-44 Wheel Lock Bolt M8x21.3L mm 3 JAT464-03 Air Inlet * 45 JAT467-45 Guard 7 in.
-
Page 16: Warranty And Service
Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist Accessories; Shop Tools; Warehouse & Dock products; Hand Tools: Air Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of ...