Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Vivo STAND-V004Y
Summary of Contents for Vivo STAND-V004Y
- Page 1 Quad Monitor Desk Mount STAND-V004Y Assembly Manual...
- Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Failure to report missing parts within 30 days may result in denial of free replacement.
-
Page 3: Package Contents
Package Contents A (x1) B (x1) C (x1) Dual Arm Lower Pole Upper Pole E (x1) F (x1) G (x1) D (x2) Clamp Pole Connector Pole Cover VESA Bracket H (x2) I (x6) J (x5) K (x1) L (x1) Pole Cable Clip Arm Cable Clip Grommet Plate Grommet... - Page 4 Assembly Steps STEP 1 Option 1: Clamp Installation Remove adhesive backing from Pads (J) and apply them evenly to the inside of Clamp (E). Thread Lower Pole (A) into Clamp and secure by tightening the set screws using 3mm Allen Wrench (T-A).
- Page 5 Option 2: Grommet Installation Use a Phillips screwdriver to remove the screw from Clamp Bolt (E1). Remove adhesive backing from Pads (J) and apply them evenly to the bottom of Grommet Plate (K). Thread Lower Pole (A) into Grommet Plate (K) and secure by tightening the set screws using 3mm Allen Wrench (T-A).
- Page 6 STEP 2 Slide Dual Arm (C) and a VESA Bracket (D) onto Lower Pole (A). Secure at the desired height by tightening the back screw using 5mm Allen Wrench (T-B). Ensure the open holes on VESA Brackets are on the top. The back screws may need to be loosened before sliding onto Pole.
- Page 7 STEP 3 Thread Pole Connector (F) onto Lower Pole (A), then thread Upper Pole (B) into Pole Connector. Secure by tightening the set screws on Pole Connector using 3mm Allen Wrench (T-A). Slide on the remaining Pole Cable Clip (H). Poles Won’t Thread Into Connector? If Poles (A,B) are difficult to thread into Pole...
- Page 8 STEP 4 Slide the remaining VESA Bracket (D) onto Upper Pole (B) at the desired height and secure by tightening the back screw using 5mm Allen Wrench (T-B). Ensure the open holes on VESA Bracket is on the top. The back screw may need to be loosened before sliding onto Pole.
- Page 9 STEP 6 Thread two appropriate Screws (M-A or M-B) with M5 Washers (M-C) into the top two holes of each monitor leaving 3mm of threading exposed. Place monitors onto the heads of Dual Arm (C) and VESA Brackets (D). Secure monitors using additional Screws (M-A or M-B) with M5 Washers (M-C). Tighten all screws using a Phillips screwdriver.
- Page 10 Adjustments Adjust the vertical tilt tension using 6mm Allen Wrench (T-C) as shown. +45 ° -45 ° If monitors are uneven, they can be shifted up or down by adjusting the top screw behind each monitor using 5mm Allen Wrench (T-B). Rotate monitors as desired. Manage cables using Pole Cable Clips (H) and Arm Cable Clips (I).
- Page 11 Assembly Complete Store Allen Wrenches (T-A, T-B, T-C) in Pole Cable Clips (H) for future adjustments.
- Page 12 Need Help? We’re Here For You Monday-Friday from 7am-7pm CST Saturday 8am-4pm CST Email Us Chat with Live Agent Give Us a Call help@vivo-us.com www.vivo-us.com 309-278-5303 ext. 1 FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us @VIVOus VIVO...
Need help?
Do you have a question about the STAND-V004Y and is the answer not in the manual?
Questions and answers