Subscribe to Our Youtube Channel
Related Manuals for Planet IGS-504PT
Summary of Contents for Planet IGS-504PT
- Page 1 Compact Industrial 4-Port 10/100/1000T 802.3at PoE + 1-Port 10/100/1000T Ethernet Switch IGS-504PT Compact Industrial 4-Port 10/100/1000T 802.3at PoE + 1-Port 100/1000X SFP Ethernet Switch IGS-514PT User's Manual...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Product Specifications ..................4 3. Hardware Introduction ................... 7 3.1 Three-View Diagram ................7 3.2 Switch Front Panel .................. 9 3.3 LED Indicators ..................9 3.4 Switch Upper Panel ................10 3.5 Wiring the Power Inputs ................ 10 3.6 Grounding the Device ................ -
Page 3: Package Contents
Ethernet Switch with 4 PoE+ ports. The interfaces of these models are shown below: In the following sections, the term “Industrial PoE+ Switch” means the IGS-504PT or IGS-514PT. Open the box of the Industrial PoE+ Switch and carefully unpack it. The box should contain the following items:... -
Page 4: Product Specifications
2. Product Specifications Model IGS-504PT IGS-514PT Hardware Specifications 5 10/100/1000BASET RJ45 4 10/100/1000BASET RJ45 Copper Ports twisted-pair auto-MDI/MDI-X twisted-pair auto-MDI/MDI-X ports, up to 100 meters ports, up to 100 meters 1 1000BASE-SX/LX/BX SFP SFP Port interface, compatible with 100BASE-FX SFP PoE Injector Ports 4 ports with 802.3at PoE+ injector function (Ports 1 to 4) - Page 5 Switch Specifications Switch Architecture Store-and-Forward Switch Fabric 10Gbps Throughput 7.4Mpps@64bytes (packet per second) Address Table 2K entries Buffer Memory 4M bits on-chip buffer memory Jumbo Frame 9Kbytes Back pressure for half duplex Flow Control IEEE 802.3x pause frame for full duplex Power over Ethernet IEEE 802.3at Power over Ethernet Plus/PSE PoE Standard Backward compatible with IEEE 802.3af Power over Ethernet/ PoE Power Supply...
- Page 6 Standards Conformance Regulatory FCC Part 15 Class A, CE Compliance IEC 60068-2-32 (free fall) Stability Testing IEC 60068-2-27 (shock) IEC 60068-2-6 (vibration) IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3ab Gigabit Ethernet IEEE 802.3z Gigabit Ethernet over Fiber Optic Standards (IGS-514PT only) Compliance...
-
Page 7: Hardware Introduction
4-pin terminal block. The LED indicators are also located on the front panel. Top View Mounting Kit Side View Front View Side View Rear View DIN-Rail Kit PoE-in-Use IGS-504PT Bottom View Mounting Kit Unit: mm Figure 3-1: IGS-504PT Three-View Diagram... - Page 8 Top View Mounting Kit Side View Front View Side View Rear View PoE-in-Use DIN-Rail Kit IGS-514PT Bottom View Mounting Kit Dimensions (W x D x H): 30 x 70 x 104 mm Figure 3-2: IGS-514PT Three-View Diagram...
-
Page 9: Switch Front Panel
3.2 Switch Front Panel PoE-in-Use PoE-in-Use IGS-504PT IGS-514PT Figure 3-3: IGS-504PT/IGS-514PT Front View 3.3 LED Indicators System Color Function Green Lights to indicate power 1 has power. Green Lights to indicate power 2 has power. 802.3at PoE+ 10/100/1000BASE-T Interfaces (Port 1 to Port 4) -
Page 10: Switch Upper Panel
10/100/1000BASE-T Interfaces (Port 5 of IGS-504PT) Color Function Lights to indicate the port is successfully established at 10/100/1000Mbps. LNK/ACT Green Blinks to indicate that the Switch is actively sending or receiving data over that port. 100/1000X SFP Interfaces (Port 5 of IGS-514PT) -
Page 11: Grounding The Device
1. The DC power input range is 48V ~ 54V DC. Please insert positive and negative DC power wires into contacts 1 and 2 for POWER 1, or 3 and 4 for POWER 2. 1 2 3 4 DC Input Range: 48-54V , 3A max. -
Page 12: Installation
DIN-rail and wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. This following pictures show how to install the device. However, the device in the picture is not IGS-504PT/IGS-514PT. 4.1 DIN-rail Installation Figure 4-1: DIN-rail Mounting Place the bracket on the back of the device and with the given 3 screws, tighten them. Slide the device with the bracket mounted through the DIN-rail to finish the... -
Page 13: Wall Mounting
4.2 Wall Mounting Figure 4-2: Wall Mounting Place both mounting plates on the back of the device, and tighten them with the given screws. Then put the device with the plates mounted on the wall, and screw them to finish the installation. 4.3 Side Wall Mounting Figure 4-3: Side Wall Mounting Place the two mounting plates on the bottom of the device, and tighten them with the given screws. -
Page 14: Customer Support
5. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource at the PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. - Page 15 FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Need help?
Do you have a question about the IGS-504PT and is the answer not in the manual?
Questions and answers